Sample NVS from machine C147. These values are a starting point for production start up only. >> nvs dump NVS Dump File - MPE Firmware Version 2.23 NVS drum calibration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- pgv prop_gain_vel 12000 12000 12000 igv integ_gain_vel 6250 6250 6250 dgv deriv_gain_vel 468 468 468 pgp prop_gain_posn 6250 6250 6250 igp integ_gain_posn 250 250 250 dgp deriv_gain_posn 5625 5625 5625 vgp vel_gain_posn 0 0 0 pgs prop_gain_soft 6250 6250 6250 igs integ_gain_soft 0 0 0 dgs deriv_gain_soft 3000 3000 3000 pgh prop_gain_hall 2000 2000 2000 igh integ_gain_hall 500 500 500 dgh deriv_gain_hall 0 0 0 epos edge_position 340 340 450 tach ticks NVS drum configuration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- vacc velocity_accel 10.000 10.000 10.000 rad/s/s pacc position_accel 6.000 6.000 6.000 rad/s/s diam nominal_diameter 286.000 286.000 286.000 mm chkfly check_flyoff 1 1 1 gear drum_gear_ratio 6 6 6 mtol move_tolerance 5 5 5 tach ticks iner drum_inertia 0.866 0.866 0.866 kg-meter^2 mtcn motor_torque_const 0.403 0.403 0.403 newton-m/A hppr hall_pulses_per_rot 6 6 6 maxdiff max_hall_vs_enc_diff 200 200 200 tach ticks doff drive_offset 34 34 0 tach ticks dfrict drum_friction 20 20 20 tach ticks tpr tach_pulses_per_rot 9000 9000 9000 tach ticks ted tach_encoder_direction 0 0 0 NVS carriage calibration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- pgain driver_plot_gain 192 192 192 mgain driver_move_gain 254 254 254 soff sine_offset 0 0 0 coff cos_offset 0 0 0 cph centre_plate_to_home 569 569 580 mm again driver_accel_gain 254 254 254 hgain driver_hold_gain 60 60 60 NVS carriage configuration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- mspeed max_speed 1500 1500 2500 mil/sec accel max_accel 1500 1500 1500 mil/s/s period accel_period 10 10 10 millisecs gearing srot_per_lrot 3 3 3 pitch mil_per_lrot 200 200 200 steps steps_per_srot 200 200 200 scyc steps_per_scyc 4 4 4 psteps plot_accel_steps 32 32 32 ispeed init_speed 500 500 500 mil/sec espeed edge_speed 250 250 250 mil/sec esearch edge_narrow_search 300 300 300 mils eatt edge_attempts 3 3 3 wsearch edge_wide_search 1000 1000 1000 mils mtravel max_travel 1162 1162 1162 mm kspeed knee_speed 0 0 0 mil/sec eaccel edge_search_accel 1500 1500 1500 mil/s/s NVS al (Autoloader) calibration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- nts no_table_sensor 0 0 0 nms no_mag_sensor 0 0 0 nlps no_load_plate_sensor 0 0 0 nps no_proximity_sensor 0 0 0 nrs no_roller_sensor 0 0 0 nus no_unload_sensor 0 0 0 ntl no_te_lock_sensor 0 0 0 nte no_te_sensor 0 0 0 nle no_le_sensor 0 0 0 nlr no_load_ramp_sensor 1 1 1 nss no_shutter_sensor 0 0 0 nds no_drawer_sensor 0 0 0 nls no_lid_sensor 0 0 0 nes no_exit_sensor 0 0 0 nbs no_bridge_sensor 1 1 1 npc no_plate_conveyor 0 0 0 nups no_unload_plate_sensor 0 0 0 npm no_picker_microsw 0 0 0 xx1 not_used1 0 0 0 nsd no_stall_detect 0 0 0 npg no_le_plate_guide 1 1 1 bte bad_te_sensor 0 0 0 turbo turbo_unload_load 0 0 0 NVS al (Autoloader) configuration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- coff clamp_offset 14350 14350 14250 tach ticks lepos le_pos 16616 16616 16465 tach ticks ppos park_pos 11887 11887 11895 tach ticks bays num_bays 4 4 2 ldvel load_vel 100.000 100.000 100.000 rpm uldvel unload_vel -100.000 -100.000 -100.000 rpm soff sensor_offset 95.000 95.000 95.000 mm low plates_low 10 10 10 test al_test_fixture 0 0 0 ssr slip_sheet_retries 2 2 2 ssd slip_sheet_detect 0 0 0 prm plate_reject_method 1 1 1 stamps number_of_stamps 10 10 10 NVS alpos (Autoloader positions) calibration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- pjy plate_jog_y 20.000 20.000 20.000 mm psy plate_search_y 71.000 71.000 70.000 mm cup cup_clear_y 1.000 1.000 1.000 mm pgy plate_get_y 10.000 10.000 9.000 mm vjy velcro_jog_y 10.000 10.000 10.000 mm try tissue_release_y 10.000 10.000 9.000 mm u1y unload_pos1_y 35.000 35.000 35.000 mm u2y unload_pos2_y 7.000 7.000 7.000 mm qpy queue_pos_y 65.000 65.000 55.000 mm lmin load_min_y 35.000 35.000 35.000 mm lmax load_max_y 55.000 55.000 55.000 mm ccy cassette_clear_y 100.000 100.000 100.000 mm scy shutter_contact_y 30.000 30.000 30.000 mm p1y process_pos1_y 0.000 0.000 0.000 mm ppz plate_pick_z 966.000 966.000 970.000 mm l1z le_move1_z 140.000 140.000 140.000 mm l2z le_move2_z 18.000 18.000 19.000 mm p1z process_pos1_z 400.000 400.000 400.000 mm qmz queue_max_z 966.000 966.000 960.000 mm qjz queue_jog_z 70.000 70.000 70.000 mm ccz cassette_clear_z 670.000 670.000 670.000 mm pcz plate_calc_z 985.000 985.000 985.000 mm vpz velcro_pos_z 890.000 890.000 890.000 mm sspz sheet_sensor_pos_z 360.000 360.000 360.000 mm qjz3 queue_jog3_z 40.000 40.000 40.000 mm qjz2 queue_jog2_z 10.000 10.000 10.000 mm trz tissue_release_z 950.000 950.000 950.000 mm cjy cassette_jog_y 0.000 0.000 0.000 mm btsy bay_tab_search_y 50.000 50.000 50.000 mm NVS aldly (Autoloader delays) calibration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- sssd slip_sheet_sensor_delay 1.000 1.000 1.000 seconds tes te_sensor_delay 0.300 0.300 0.300 seconds wp wiper_delay 3.000 3.000 3.000 seconds rot rotate_delay 1.500 1.500 1.500 seconds untilt untilt_delay 2.000 2.000 2.000 seconds queue queue_delay 2.000 2.000 2.000 seconds air airblast_delay 3.000 3.000 3.000 seconds air2 airblast2_delay 2.000 2.000 2.000 seconds vac vac_delay 2.500 2.500 2.500 seconds release release_delay 1.000 1.000 1.000 seconds le le_delay 4.000 4.000 4.000 seconds roller roller_delay 4.000 4.000 4.000 seconds te te_delay 4.000 4.000 4.000 seconds ttilt t_tilt_delay 5.000 5.000 5.000 seconds tuntilt t_untilt_delay 5.000 5.000 5.000 seconds uvac uvac_delay 1.500 1.500 1.500 seconds uldly unload_delay 10.000 10.000 10.000 seconds teul te_ulock_delay 1.000 1.000 1.000 seconds exit exit_door_delay 4.000 4.000 2.000 seconds sensor sensor_delay 0.500 0.500 0.500 seconds shut shutter_delay 4.000 4.000 4.000 seconds lid cassette_lid_delay 5.000 5.000 5.000 seconds lr load_ramp_delay 0.100 0.100 0.100 seconds pid processor_infeed_delay 30.000 30.000 30.000 seconds tbs time_between_stamps 2.000 2.000 3.000 seconds tps time_per_stamp 0.300 0.300 0.300 seconds NVS aldrv (Autoloader drive) configuration [1]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- limit travel_limit 2635.000 2635.000 0.000 mm sf slow_f 1 1 0 sr slow_r 1 1 0 ss slow_s 10 10 0 mf med_f 2 2 0 mr med_r 8 8 0 ms med_s 3 3 0 ff fast_f 5 5 0 fr fast_r 50 50 0 fs fast_s 100 100 0 half half_step 2 2 1 dia pulley_dia 60 60 10 mm ratio ratio 27 27 1 steps steps_per_rev 200 200 200 NVS aldrv (Autoloader drive) configuration [2]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- limit travel_limit 966.000 966.000 0.000 mm sf slow_f 10 10 0 sr slow_r 12 12 0 ss slow_s 250 250 0 mf med_f 15 15 0 mr med_r 44 44 0 ms med_s 200 200 0 ff fast_f 20 20 0 fr fast_r 52 52 0 fs fast_s 200 200 0 half half_step 2 2 1 dia pulley_dia 55 55 10 mm ratio ratio 125 125 1 steps steps_per_rev 200 200 200 NVS altim (Autoloader timeouts) configuration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- cmd cmd_timeout 0.100 0.100 0.100 seconds leave leave_timeout 0.500 0.500 0.500 seconds suspend suspend_timeout 5 5 5 seconds move move_timeout 200 200 200 seconds yhome y_home_timeout 180 180 180 seconds pick pick_timeout 180 180 180 seconds load load_timeout 100 100 100 seconds unload unload_timeout 100 100 100 seconds process process_timeout 100 100 100 seconds cb_load load_drawer 4 4 4 seconds plate plate_process 100 100 100 seconds zhome z_home_timeout 30 30 30 seconds eject eject_timeout 10 10 10 seconds stall tissue_stall_timeout 10 10 10 seconds NVS dpe (Data Path) calibration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- dly old_data_delay 100 100 100 pixels NVS dpe (Data Path) configuration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- pbw mode1_spot_width 3 3 3 pixels pbi profile_bit_inc 10 10 10 pixels mzs mscan_zone_size 200 200 200 mils scs scorr_sample_count 1 1 1 NVS head (Exposure Head) calibration: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- sn serial_number 1947 1947 0 fshift fs_mod_shift 62 62 55 wpwrcal wr_laser_cal 239.400 239.400 0.000 r0 reserved0 0.000 0.000 0.000 swidth stroke_width 192 192 240 soffset stroke_offset 24 24 0 lvbias lv_bias 4 4 4 onthresh on_plate_thresh 988 988 1000 offthresh off_plate_thresh 4 4 0 r1 reserved1 0 0 0 r2 reserved2 0 0 0 fpowercal fs_laser_pwr_cal 0.000 0.000 0.000 ferrcal fs_error_cal 3.130 3.130 3.000 fmod fs_laser_mod 0.000 0.000 -0.020 lposcal lens_position_cal 2.633 2.633 3.000 r6 reserved6 0.000 0.000 0.000 fsphase fs_phase_offset 45 45 0 scanscale scan_corr_scale 160 160 0 fheadcal focus_head_cal 7.800 7.800 5.000 fmodcal fmod_cal 100 100 100 hpslope head_power_slope 300.000 300.000 300.000 hpoffset head_power_offset 0.000 0.000 0.000 nomlsrcur nom_laser_current 27.700 27.700 27.300 amps swidthn stroke_width_nrw 120 120 120 soffsetn stroke_offset_nrw 56 56 56 casehigh case_high_warning 0.000 0.000 32.000 degrees C caselow case_low_warning 0.000 0.000 28.000 degrees C humidity humidity_alarm 30.000 30.000 30.000 % NVS head (Exposure Head) configuration: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- fkp focus_Kp 0.200 0.200 0.250 fki focus_Ki 0.035 0.035 0.090 fkd focus_Kd 1.200 1.200 1.200 lkp fs_learn_Kp 0.500 0.500 0.500 r3 reserved3 0 0 0 padvance fs_phase_advance 12 12 6 lpkp lens_posn_Kp 3.100 3.100 6.000 lpki lens_posn_Ki 0.020 0.020 0.120 lpkd lens_posn_Kd 15.000 15.000 32.000 lpos lens_position 0 0 0 microns r4 reserved4 0 0 0 foffset fs_offset 50 50 0 acurrent fs_act_current 0 0 0 fsample fs_sample_rate 1 1 1 fthresh focus_error_thresh 150 150 150 ferrdur focus_error_duration 50 50 50 fsettle focus_settle_time 6 6 6 fpower fs_laser_pwr 0.000 0.000 1.000 milliwatts r5 reserved5 0 0 0 bkp bm_posn_Kp 5.000 5.000 1.000 bki bm_posn_Ki 0.200 0.200 0.050 bkd bm_posn_Kd 0.000 0.000 0.000 bposn bm_position 0 0 0 bsample bm_sample_rate 24 24 24 wkp wr_laser_Kp 0.350 0.350 0.350 wki wr_laser_Ki 0.110 0.110 0.110 wkd wr_laser_Kd 0.000 0.000 0.000 wenable wr_laser_enable 1 1 1 wsample wr_sample_rate 49 49 49 bpgain us_gain 45 45 40 bpoffset us_offset 40 40 0 bpmaxerr us_maxerr 3.000 3.000 2.000 % scanlpos scan_lens_position 200 200 200 microns scands scan_drum_speed 14.000 14.000 10.000 rpm nlpwm non_linear_pwm 0 0 0 vb verbose 0 0 0 hpwrgain head_power_gain 9 9 50 lsrmode laser_mode 0 0 0 flpos focus_init_lpos -100 -100 0 microns diag0 diag0 0 0 0 diag1 diag1 0 0 0 diag2 diag2 0 0 0 diag3 diag3 0 0 0 diag4 diag4 0 0 0 diag5 diag5 0 0 0 r7 reserved7 0 0 0 type head_type 0 0 0 NVS sys (System) calibration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- sn serial_number 147 147 0 m1 macro1 "" "" m2 macro2 "" "" m3 macro3 "" "" NVS sys (System) configuration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- ntau nco_filter_tau 3 3 3 pgain pll_gain 32 32 32 tstatus status_filter_length 4 4 4 tstate state_filter_length 4 4 4 wd ws_watchdog_timeout 2 2 2 minutes eis extra_invert_stroke 0 0 0 cpy chars_per_yield 100 100 100 ews echo_ws_status 1 1 1 ewc echo_ws_commands 1 1 1 tstk stroke_update_interval 540 540 540 minutes track report_tracking 1 1 1 mb1 must_be_1 1 1 1 maxis max_image_size 31.200 31.200 32.200 inches load load_plate 1 1 1 bench bench_mode 0 0 0 wsb ws_baud_rate 2400 2400 2400 sig display_signatures 0 0 0 ewd echo_watchdog 0 0 0 asr abort_on_scsi_reset 0 0 0 r2 reserved2 0 0 0 sid scsi_id 5 5 5 ntu nco_tach_update 60 60 60 s1 stroke_stats1_mode 1 1 1 s2 stroke_stats2_mode 2 2 2 ism image_size_margin 0 0 0 "/10 hi head_installed 1 1 1 res default_res_mode 0 0 0 asp asynch_series_period 1.000 1.000 1.000 inches ast asynch_series_pause 0 0 0 seconds es enable_sensitivity 0 0 0 newd new_drum_speed 0 0 0 dlys delay_scsi_start 1 1 1 scanntu scan_nco_tach_update 0 0 0 dhi display_head_incoming 0 0 0 dho display_head_outgoing 0 0 0 NVS hdp (Head Dependant Parameters) calibration: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- fmsl f_m_series_length 20 20 20 steps fmsw f_m_series_width 1.000 1.000 1.000 inches r0 reserved0 0.000 0.000 0.000 sssa sscan_shift_adjust -52.604 -52.604 0.000 mils rt recalibration_time 1 1 1 minutes dpi head_dpi 2400 2400 2400 NVS hdp (Head Dependant Parameters) configuration: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- lrt laser_ready_time 180 180 180 seconds brt beam_balance_ready 20 20 20 seconds r1 reserved1 0 0 0 r2 reserved2 0 0 0 r3 reserved3 0 0 0 fnm force_narrow_mode 0 0 0 NVS gc (Geom Correction) calibration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- mssa mscan_shift_adjust 23.058 23.058 0.000 mils msca mscan_scale_adjust -275 -275 0 ppm ssca sscan_scale_adjust -46 -46 0 ppm prot plate_rotate -28 -28 0 microrads ortho orthog_adjust 14 14 0 microrads tinc track_profile_inc 8 8 0 inches trk[ 0] track_profile -0.392 -0.392 0 mils trk[ 1] track_profile 0.123 0.123 0 mils trk[ 2] track_profile 0.326 0.326 0 mils trk[ 3] track_profile 0.278 0.278 0 mils trk[ 4] track_profile 0.014 0.014 0 mils trk[ 5] track_profile -0.350 -0.350 0 mils trk[ 6] track_profile 0.000 0.000 0 mils trk[ 7] track_profile 0.000 0.000 0 mils trk[ 8] track_profile 0.000 0.000 0 mils trk[ 9] track_profile 0.000 0.000 0 mils trk[10] track_profile 0.000 0.000 0 mils trk[11] track_profile 0.000 0.000 0 mils trk[12] track_profile 0.000 0.000 0 mils trk[13] track_profile 0.000 0.000 0 mils trk[14] track_profile 0.000 0.000 0 mils trk[15] track_profile 0.000 0.000 0 mils trk[16] track_profile 0.000 0.000 0 mils trk[17] track_profile 0.000 0.000 0 mils trk[18] track_profile 0.000 0.000 0 mils trk[19] track_profile 0.000 0.000 0 mils trk[20] track_profile 0.000 0.000 0 mils trk[21] track_profile 0.000 0.000 0 mils trk[22] track_profile 0.000 0.000 0 mils NVS gc (Geom Correction) configuration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- mss mscan_shift 300.000 300.000 300.000 mils sss sscan_shift 0.000 0.000 0.000 mils eno enable_orthog 1 1 1 ftc frame_temp_coef 24 24 24 ppm/C lstc leadscrew_temp_coef 12 12 12 ppm/C engc enable_gc 1 1 1 mbp measure_beam_pos 0 0 0 cbp cal_beam_pos 0 0 0 NVS bay (Cassette Bay) calibration [1]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- loc bay_location 1029.000 1029.000 0.000 mm NVS bay (Cassette Bay) calibration [2]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- loc bay_location 1562.000 1562.000 0.000 mm NVS bay (Cassette Bay) calibration [3]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- loc bay_location 2097.000 2097.000 0.000 mm NVS bay (Cassette Bay) calibration [4]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- loc bay_location 2630.000 2630.000 0.000 mm NVS bay (Cassette Bay) calibration [5]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- loc bay_location 0.000 0.000 0.000 mm NVS bay (Cassette Bay) calibration [6]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- loc bay_location 0.000 0.000 0.000 mm NVS bay (Cassette Bay) calibration [7]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- loc bay_location 0.000 0.000 0.000 mm NVS bay (Cassette Bay) calibration [8]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- loc bay_location 0.000 0.000 0.000 mm NVS bay (Cassette Bay) calibration [9]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- loc bay_location 0.000 0.000 0.000 mm NVS bay (Cassette Bay) calibration [10]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- loc bay_location 0.000 0.000 0.000 mm NVS mode (Plot Modes) calibration [1]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- mssa mscan_shift_adjust 0.000 0.000 0.000 mils sssa sscan_shift_adjust 0.000 0.000 0.000 mils msa mscan_scale_adjust 0 0 0 ppm ssa sscan_scale_adjust 0 0 0 ppm exp exposure_adjust 0 0 0 ppm mis mscan_image_size 77280 77280 77280 pixels ess exp_series_start 150.000 150.000 150.000 mJ/cm^2 esi exp_series_step 10.000 10.000 10.000 % edge find_edge 1 1 1 skr skip_rotations 0 0 0 inv invert 0 0 0 mir mirror 0 0 0 is image_side 0 0 0 sl series_length 15 15 15 steps ikb ink_key_bits 0 0 0 ikt ink_key_transitions 0 0 0 ikms mscan_sample_size 0.000 0.000 0.000 inches ikss sscan_sample_size 0.000 0.000 0.000 inches sw series_strip_width 1.500 1.500 1.500 inches iw image_width 0 0 0 mils ss stroke_shift_pixels 0 0 0 pixels rbo rip_byte_order 4 4 4 nm narrow_mode 0 0 0 NVS mode (Plot Modes) configuration [1]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- dpi rip_dpi 2400 2400 2400 pps pixels_per_stroke 192 192 240 pcd pixel_clock_divisor 8 8 8 msd mscan_duplicate 1 1 1 ssd sscan_duplicate 1 1 1 NVS mode (Plot Modes) calibration [3]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- mssa mscan_shift_adjust 0.000 0.000 0.000 mils sssa sscan_shift_adjust 0.000 0.000 0.000 mils msa mscan_scale_adjust 0 0 0 ppm ssa sscan_scale_adjust 0 0 0 ppm exp exposure_adjust 0 0 0 ppm mis mscan_image_size 38640 38640 77280 pixels ess exp_series_start 150.000 150.000 150.000 mJ/cm^2 esi exp_series_step 10.000 10.000 10.000 % edge find_edge 1 1 1 skr skip_rotations 0 0 0 inv invert 0 0 0 mir mirror 0 0 0 is image_side 0 0 0 sl series_length 15 15 15 steps ikb ink_key_bits 0 0 0 ikt ink_key_transitions 0 0 0 ikms mscan_sample_size 0.000 0.000 0.000 inches ikss sscan_sample_size 0.000 0.000 0.000 inches sw series_strip_width 1.500 1.500 1.500 inches iw image_width 0 0 0 mils ss stroke_shift_pixels 0 0 0 pixels rbo rip_byte_order 4 4 4 nm narrow_mode 0 0 0 NVS mode (Plot Modes) configuration [3]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- dpi rip_dpi 1200 1200 2400 pps pixels_per_stroke 192 192 240 pcd pixel_clock_divisor 8 8 8 msd mscan_duplicate 2 2 1 ssd sscan_duplicate 2 2 1 NVS status (Status Flag Masks) calibration [1]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- mask status_mask 8 8 0 NVS status (Status Flag Masks) calibration [2]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- mask status_mask 4293919232 4293919232 0 NVS status (Status Flag Masks) calibration [3]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- mask status_mask 0 0 0 NVS status (Status Flag Masks) calibration [4]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- mask status_mask 0 0 0 NVS status (Status Flag Masks) calibration [5]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- mask status_mask 0 0 0 NVS oldmedia (obsolete) calibration [1]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" mcode media_code 0 0 0 fpos filter_position 1 1 1 stol stroke_tolerance 0.300 0.300 0.300 % ltol tolerance_limit 1.000 1.000 1.000 % sens default_sensitivity 170.000 170.000 170.000 uJ/cm^2 sm sensitivity_slope 0.000 0.000 0.000 uJ/cm^2/C srt sens_recal_thresh 10 10 10 % inv invert 0 0 0 rexp reject_exp_time 7000 7000 7000 millisecs proc processor 2 2 2 pcode processor_code 0 0 0 cspd conveyor_speed 4095 4095 4095 tc temp_coef 0 0 0 ppm/C escan extra_scanlines 0 0 0 esp exp_series_pattern 4 4 4 thk default_thickness 305 305 305 microns NVS oldmedia (obsolete) calibration [2]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" mcode media_code 0 0 0 fpos filter_position 1 1 1 stol stroke_tolerance 0.300 0.300 0.300 % ltol tolerance_limit 1.000 1.000 1.000 % sens default_sensitivity 170.000 170.000 170.000 uJ/cm^2 sm sensitivity_slope 0.000 0.000 0.000 uJ/cm^2/C srt sens_recal_thresh 10 10 10 % inv invert 0 0 0 rexp reject_exp_time 7000 7000 7000 millisecs proc processor 2 2 2 pcode processor_code 0 0 0 cspd conveyor_speed 4095 4095 4095 tc temp_coef 0 0 0 ppm/C escan extra_scanlines 0 0 0 esp exp_series_pattern 4 4 4 thk default_thickness 305 305 305 microns NVS media (Media Types) calibration [1]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "Kodak IR" "Kodak IR" colour proofer_colour "" "" mcode media_code 0 0 0 abl ablative 0 0 0 0=No,1=Yes cthk carrier_thickness 0 0 0 microns sens default_sensitivity 170.000 170.000 170.000 mJ/cm^2 inv invert 0 0 0 rexp reject_exp_time 7000 7000 7000 millisecs proc processor 2 2 2 pcode processor_code 0 0 0 cspd conveyor_speed 255 255 4095 escan extra_scanlines 1 1 0 esp exp_series_pattern 50 50 50 thk default_thickness 305 305 305 microns mdt max_door_time 45 45 0 seconds sr surface_reflectivity 0.160 0.160 0.100 sd surface_depth 0 0 0 microns dr debris_removal 1 1 1 ow overwriting 0 0 0 mlc media_load_clean 0 0 0 NVS media (Media Types) calibration [2]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "Drytech" "Drytech" colour proofer_colour "" "" mcode media_code 1 1 0 abl ablative 0 0 0 0=No,1=Yes cthk carrier_thickness 0 0 0 microns sens default_sensitivity 120.000 120.000 170.000 mJ/cm^2 inv invert 0 0 0 rexp reject_exp_time 7000 7000 7000 millisecs proc processor 2 2 2 pcode processor_code 0 0 0 cspd conveyor_speed 255 255 4095 escan extra_scanlines 0 0 0 esp exp_series_pattern 50 50 50 thk default_thickness 152 152 305 microns mdt max_door_time 300 300 0 seconds sr surface_reflectivity 0.500 0.500 0.100 sd surface_depth 30 30 0 microns dr debris_removal 0 0 1 ow overwriting 0 0 0 mlc media_load_clean 0 0 0 NVS media (Media Types) calibration [3]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "Prisma" "Prisma" colour proofer_colour "" "" mcode media_code 0 0 0 abl ablative 0 0 0 0=No,1=Yes cthk carrier_thickness 0 0 0 microns sens default_sensitivity 180.000 180.000 170.000 mJ/cm^2 inv invert 1 1 0 rexp reject_exp_time 7000 7000 7000 millisecs proc processor 2 2 2 pcode processor_code 0 0 0 cspd conveyor_speed 255 255 4095 escan extra_scanlines 1 1 0 esp exp_series_pattern 50 50 50 thk default_thickness 305 305 305 microns mdt max_door_time 300 300 0 seconds sr surface_reflectivity 0.210 0.210 0.100 sd surface_depth 0 0 0 microns dr debris_removal 1 1 1 ow overwriting 0 0 0 mlc media_load_clean 0 0 0 NVS media (Media Types) calibration [4]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "Electra" "Electra" colour proofer_colour "" "" mcode media_code 0 0 0 abl ablative 0 0 0 0=No,1=Yes cthk carrier_thickness 0 0 0 microns sens default_sensitivity 200.000 200.000 170.000 mJ/cm^2 inv invert 1 1 0 rexp reject_exp_time 7000 7000 7000 millisecs proc processor 2 2 2 pcode processor_code 0 0 0 cspd conveyor_speed 255 255 4095 escan extra_scanlines 1 1 0 esp exp_series_pattern 50 50 50 thk default_thickness 305 305 305 microns mdt max_door_time 300 300 0 seconds sr surface_reflectivity 0.210 0.210 0.100 sd surface_depth 0 0 0 microns dr debris_removal 1 1 1 ow overwriting 0 0 0 mlc media_load_clean 0 0 0 NVS media (Media Types) calibration [5]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "LH-PI" "LH-PI" colour proofer_colour "" "" mcode media_code 0 0 0 abl ablative 0 0 0 0=No,1=Yes cthk carrier_thickness 0 0 0 microns sens default_sensitivity 180.000 180.000 170.000 mJ/cm^2 inv invert 1 1 0 rexp reject_exp_time 7000 7000 7000 millisecs proc processor 1 1 2 pcode processor_code 0 0 0 cspd conveyor_speed 255 255 4095 escan extra_scanlines 1 1 0 esp exp_series_pattern 12 12 50 thk default_thickness 240 240 305 microns mdt max_door_time 300 300 0 seconds sr surface_reflectivity 0.120 0.120 0.100 sd surface_depth 0 0 0 microns dr debris_removal 1 1 1 ow overwriting 0 0 0 mlc media_load_clean 0 0 0 NVS media (Media Types) calibration [6]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" colour proofer_colour "" "" mcode media_code 0 0 0 abl ablative 0 0 0 0=No,1=Yes cthk carrier_thickness 0 0 0 microns sens default_sensitivity 170.000 170.000 170.000 mJ/cm^2 inv invert 0 0 0 rexp reject_exp_time 7000 7000 7000 millisecs proc processor 2 2 2 pcode processor_code 0 0 0 cspd conveyor_speed 255 255 4095 escan extra_scanlines 0 0 0 esp exp_series_pattern 50 50 50 thk default_thickness 305 305 305 microns mdt max_door_time 0 0 0 seconds sr surface_reflectivity 0.100 0.100 0.100 sd surface_depth 0 0 0 microns dr debris_removal 1 1 1 ow overwriting 0 0 0 mlc media_load_clean 0 0 0 NVS media (Media Types) calibration [7]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" colour proofer_colour "" "" mcode media_code 0 0 0 abl ablative 0 0 0 0=No,1=Yes cthk carrier_thickness 0 0 0 microns sens default_sensitivity 170.000 170.000 170.000 mJ/cm^2 inv invert 0 0 0 rexp reject_exp_time 7000 7000 7000 millisecs proc processor 2 2 2 pcode processor_code 0 0 0 cspd conveyor_speed 255 255 4095 escan extra_scanlines 0 0 0 esp exp_series_pattern 50 50 50 thk default_thickness 305 305 305 microns mdt max_door_time 0 0 0 seconds sr surface_reflectivity 0.100 0.100 0.100 sd surface_depth 0 0 0 microns dr debris_removal 1 1 1 ow overwriting 0 0 0 mlc media_load_clean 0 0 0 NVS media (Media Types) calibration [8]: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" colour proofer_colour "" "" mcode media_code 0 0 0 abl ablative 0 0 0 0=No,1=Yes cthk carrier_thickness 0 0 0 microns sens default_sensitivity 170.000 170.000 170.000 mJ/cm^2 inv invert 0 0 0 rexp reject_exp_time 7000 7000 7000 millisecs proc processor 2 2 2 pcode processor_code 0 0 0 cspd conveyor_speed 255 255 4095 escan extra_scanlines 0 0 0 esp exp_series_pattern 50 50 50 thk default_thickness 305 305 305 microns mdt max_door_time 0 0 0 seconds sr surface_reflectivity 0.100 0.100 0.100 sd surface_depth 0 0 0 microns dr debris_removal 1 1 1 ow overwriting 0 0 0 mlc media_load_clean 0 0 0 NVS sat (Satellite Boards) calibration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- pvg pkr_vac_gain 102 102 102 pvo pkr_vac_offset 42 42 42 uvg unld_vac_gain 102 102 102 uvo unld_vac_offset 42 42 42 tr0 ThermistorRef0 4990 4990 4990 ohms tr1 ThermistorRef1 4990 4990 4990 ohms tr2 ThermistorRef2 4990 4990 4990 ohms tr3 ThermistorRef3 4990 4990 4990 ohms fsc0 FullScaleCal0 4095 4095 4095 zsc0 ZeroScaleCal0 0 0 0 fsc1 FullScaleCal1 4095 4095 4095 zsc1 ZeroScaleCal1 0 0 0 fsc2 FullScaleCal2 4095 4095 4095 zsc2 ZeroScaleCal2 0 0 0 fsc3 FullScaleCal3 4095 4095 4095 zsc3 ZeroScaleCal3 0 0 0 pvt pvac_threshold 88 88 60 uvt uvac_threshold 96 96 50 ltpmax ldr_testpoint_max 4095 4095 4095 ltpmin ldr_testpoint_min 0 0 0 ptpmax pkr_testpoint_max 4095 4095 4095 ptpmin pkr_testpoint_min 0 0 0 NVS sat (Satellite Boards) configuration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- state state 0 0 0 et engine_temp 1 1 1 lst leadscrew_temp 1 1 1 st0 spare_temp0 0 0 0 st1 spare_temp1 0 0 0 luec lu_err_chk 1 1 1 cbec cb_err_chk 1 1 1 ppec pp_err_chk 1 1 1 pdec pd_err_chk 1 1 1 zbrake z_brake_err_chk 1 1 1 NVS temp (Temp Parameters) calibration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- b1 byte1 0 0 0 b2 byte2 0 0 0 b3 byte3 0 0 0 b4 byte4 0 0 0 w1 word1 0 0 0 w2 word2 0 0 0 w3 word3 0 0 0 w4 word4 0 0 0 l1 lword1 0 0 0 l2 lword2 0 0 0 l3 lword3 0 0 0 l4 lword4 0 0 0 NVS hdm (Head Media Parameters) calibration [1]: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "Kodak IR" "Kodak IR" colour proofer_colour "" "" bmcurve beam_curvature 1 1 0 % bmslope beam_slope 1 1 0 % fmode focus_mode 4 4 0 fspeed fast_carriage_speed 198.200 198.200 198.200 mil/sec sspeed stnd_carriage_speed 133.300 133.300 133.300 mil/sec ds drum_speed 185.000 185.000 150.000 rpm wpower wr_laser_power 7.750 7.750 10.000 watts bmcurven beam_curvature_nrw 0 0 0 % bmslopen beam_slope_nrw 0 0 0 % dsn drum_speed_nrw 185.000 185.000 150.000 rpm wpowern wr_laser_power_nrw 7.750 7.750 10.000 watts r0 reserved0 0 0 0 r1 reserved1 0 0 0 r2 reserved2 0 0 0 r3 reserved3 0 0 0 wpowers wr_laser_power_std 0.000 0.000 0.000 watts NVS hdm (Head Media Parameters) calibration [2]: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" colour proofer_colour "" "" bmcurve beam_curvature 0 0 0 % bmslope beam_slope 0 0 0 % fmode focus_mode 0 0 0 fspeed fast_carriage_speed 198.200 198.200 198.200 mil/sec sspeed stnd_carriage_speed 133.300 133.300 133.300 mil/sec ds drum_speed 150.000 150.000 150.000 rpm wpower wr_laser_power 10.000 10.000 10.000 watts bmcurven beam_curvature_nrw 0 0 0 % bmslopen beam_slope_nrw 0 0 0 % dsn drum_speed_nrw 150.000 150.000 150.000 rpm wpowern wr_laser_power_nrw 10.000 10.000 10.000 watts r0 reserved0 0 0 0 r1 reserved1 0 0 0 r2 reserved2 0 0 0 r3 reserved3 0 0 0 wpowers wr_laser_power_std 0.000 0.000 0.000 watts NVS hdm (Head Media Parameters) calibration [3]: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" colour proofer_colour "" "" bmcurve beam_curvature 0 0 0 % bmslope beam_slope 0 0 0 % fmode focus_mode 0 0 0 fspeed fast_carriage_speed 198.200 198.200 198.200 mil/sec sspeed stnd_carriage_speed 133.300 133.300 133.300 mil/sec ds drum_speed 150.000 150.000 150.000 rpm wpower wr_laser_power 10.000 10.000 10.000 watts bmcurven beam_curvature_nrw 0 0 0 % bmslopen beam_slope_nrw 0 0 0 % dsn drum_speed_nrw 150.000 150.000 150.000 rpm wpowern wr_laser_power_nrw 10.000 10.000 10.000 watts r0 reserved0 0 0 0 r1 reserved1 0 0 0 r2 reserved2 0 0 0 r3 reserved3 0 0 0 wpowers wr_laser_power_std 0.000 0.000 0.000 watts NVS hdm (Head Media Parameters) calibration [4]: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" colour proofer_colour "" "" bmcurve beam_curvature 0 0 0 % bmslope beam_slope 0 0 0 % fmode focus_mode 0 0 0 fspeed fast_carriage_speed 198.200 198.200 198.200 mil/sec sspeed stnd_carriage_speed 133.300 133.300 133.300 mil/sec ds drum_speed 150.000 150.000 150.000 rpm wpower wr_laser_power 10.000 10.000 10.000 watts bmcurven beam_curvature_nrw 0 0 0 % bmslopen beam_slope_nrw 0 0 0 % dsn drum_speed_nrw 150.000 150.000 150.000 rpm wpowern wr_laser_power_nrw 10.000 10.000 10.000 watts r0 reserved0 0 0 0 r1 reserved1 0 0 0 r2 reserved2 0 0 0 r3 reserved3 0 0 0 wpowers wr_laser_power_std 0.000 0.000 0.000 watts NVS hdm (Head Media Parameters) calibration [5]: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" colour proofer_colour "" "" bmcurve beam_curvature 0 0 0 % bmslope beam_slope 0 0 0 % fmode focus_mode 0 0 0 fspeed fast_carriage_speed 198.200 198.200 198.200 mil/sec sspeed stnd_carriage_speed 133.300 133.300 133.300 mil/sec ds drum_speed 150.000 150.000 150.000 rpm wpower wr_laser_power 10.000 10.000 10.000 watts bmcurven beam_curvature_nrw 0 0 0 % bmslopen beam_slope_nrw 0 0 0 % dsn drum_speed_nrw 150.000 150.000 150.000 rpm wpowern wr_laser_power_nrw 10.000 10.000 10.000 watts r0 reserved0 0 0 0 r1 reserved1 0 0 0 r2 reserved2 0 0 0 r3 reserved3 0 0 0 wpowers wr_laser_power_std 0.000 0.000 0.000 watts NVS hdm (Head Media Parameters) calibration [6]: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" colour proofer_colour "" "" bmcurve beam_curvature 0 0 0 % bmslope beam_slope 0 0 0 % fmode focus_mode 0 0 0 fspeed fast_carriage_speed 198.200 198.200 198.200 mil/sec sspeed stnd_carriage_speed 133.300 133.300 133.300 mil/sec ds drum_speed 150.000 150.000 150.000 rpm wpower wr_laser_power 10.000 10.000 10.000 watts bmcurven beam_curvature_nrw 0 0 0 % bmslopen beam_slope_nrw 0 0 0 % dsn drum_speed_nrw 150.000 150.000 150.000 rpm wpowern wr_laser_power_nrw 10.000 10.000 10.000 watts r0 reserved0 0 0 0 r1 reserved1 0 0 0 r2 reserved2 0 0 0 r3 reserved3 0 0 0 wpowers wr_laser_power_std 0.000 0.000 0.000 watts NVS hdm (Head Media Parameters) calibration [7]: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" colour proofer_colour "" "" bmcurve beam_curvature 0 0 0 % bmslope beam_slope 0 0 0 % fmode focus_mode 0 0 0 fspeed fast_carriage_speed 198.200 198.200 198.200 mil/sec sspeed stnd_carriage_speed 133.300 133.300 133.300 mil/sec ds drum_speed 150.000 150.000 150.000 rpm wpower wr_laser_power 10.000 10.000 10.000 watts bmcurven beam_curvature_nrw 0 0 0 % bmslopen beam_slope_nrw 0 0 0 % dsn drum_speed_nrw 150.000 150.000 150.000 rpm wpowern wr_laser_power_nrw 10.000 10.000 10.000 watts r0 reserved0 0 0 0 r1 reserved1 0 0 0 r2 reserved2 0 0 0 r3 reserved3 0 0 0 wpowers wr_laser_power_std 0.000 0.000 0.000 watts NVS hdm (Head Media Parameters) calibration [8]: (NVS checksum PASS) Head data loaded, active values match head saved values Head & MPE Set name Full name Active Saved Default Units ------------------------------------------------------------------------- name media_type_name "" "" colour proofer_colour "" "" bmcurve beam_curvature 0 0 0 % bmslope beam_slope 0 0 0 % fmode focus_mode 0 0 0 fspeed fast_carriage_speed 198.200 198.200 198.200 mil/sec sspeed stnd_carriage_speed 133.300 133.300 133.300 mil/sec ds drum_speed 150.000 150.000 150.000 rpm wpower wr_laser_power 10.000 10.000 10.000 watts bmcurven beam_curvature_nrw 0 0 0 % bmslopen beam_slope_nrw 0 0 0 % dsn drum_speed_nrw 150.000 150.000 150.000 rpm wpowern wr_laser_power_nrw 10.000 10.000 10.000 watts r0 reserved0 0 0 0 r1 reserved1 0 0 0 r2 reserved2 0 0 0 r3 reserved3 0 0 0 wpowers wr_laser_power_std 0.000 0.000 0.000 watts NVS config (Machine Configuration) configuration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- conv conveyor 1 1 0 speed speed 1 1 0 msz mscan_size 32 32 32 inches ssz sscan_size 44 44 44 inches res resolutions 28 28 28 al alexist 1 1 1 engine engexist 1 1 1 type machtype "3244F" "3244F" serial serialno "C147" "C147" owner ownername "" "" NVS verbose (Debug verbose info) configuration: (NVS checksum PASS) Set name Full name Active Saved Default Units ------------------------------------------------------------------------- all all 0 0 0 monitor monitor 0 0 0 sys system 0 0 0 ws workstation 0 0 0 plot plot_mgr 0 0 0 datalink datalink 0 0 0 eh exp_head 0 0 0 drum drum 0 0 0 aldrv al_drive 0 0 0 alconv al_conv 0 0 0 alcmd al_command 0 0 0 carriage carriage 0 0 0 alsched al_sched 0 0 0 timer timer 0 0 0 image0 image0 0 0 0 image1 image1 0 0 0 image2 image2 0 0 0 suspend suspend_list_all 0 0 0