NumberError MessageError Family
33256   BFD: Not in download state   Binary File Download
33257   BFD: Firmware already in download mode   Binary File Download
33258   BFD: Binary file download not complete   Binary File Download
33259   BFD: Invalid download handle   Binary File Download
33260   BFD: Binary File Header bytes were not zero   Binary File Download
33261   BFD: Binary File Illegal Tag value(s) found   Binary File Download
33262   BFD: Unknown download type   Binary File Download
33263   BFD: unknown destination type specified   Binary File Download
33264   BFD: Bad checksum calculated   Binary File Download
33265   BFD: DOWNLOAD START message received, but not in IDLE state   Binary File Download
33266   BFD: CPU reset type equals boot level   Binary File Download
33267   BFD: Unknown Flash Manufacturer   Binary File Download
33268   BFD: Unknown Flash Device or Failure Identifying Flash Device   Binary File Download
33269   BFD: Failure writing flash   Binary File Download
33270   BFD: Failure writing FW Dir entry for BBR Code   Binary File Download
33271   BFD: Failure writing FW Dir entry for Xilinx   Binary File Download
33273   BFD: No firmware directory entries available   Binary File Download
33274   BFD: Error code not used   Binary File Download
33276   BFD: Binary Upload data is exhausted   Binary File Download
33277   BFD: Failure writing FW Dir entry for Overwriting data   Binary File Download
33501   MSG: Message not reserved   Messaging
33502   MSG: Invalid argument list   Messaging
33503   MSG: Incorrect message type   Messaging
33504   MSG: Incorrect message group   Messaging
33505   MSG: Command queue is empty   Messaging
33506   MSG: Timeout waiting on command queue   Messaging
33507   MSG: String queue is empty   Messaging
33508   MSG: Timeout waiting on string queue   Messaging
33509   MSG: Message not released   Messaging
33510   MSG: No messages in pool remaining   Messaging
33511   MSG: Timeout waiting for message response   Messaging
33512   MSG: Maximum head message is 31 bytes   Messaging
33513   MSG: Failure Sending String Message - Queue Full   Messaging
33514   MSG: No strings in pool remaining   Messaging
33516   MSG: Message tracing is disabled   Messaging
33517   MSG: Zero message trace buffers are allocated   Messaging
33518   MSG: Internal firmware error   Messaging
33519   MSG: Command code is filtered and not logged into trace buffer   Messaging
33520   MSG: Message tracing is not disabled, cannot perform requested action   Messaging
33521   MSG: Reached the end of the message trace buffer list   Messaging
33522   MSG: No more free message trace filter entries   Messaging
33523   MSG: A trace filter with the specified command code exists   Messaging
33524   MSG: Command code not in trace filter list   Messaging
33600   STG: Storage Key was not found   Non-Volatile Storage
33601   STG: Storage Key data block is the wrong size   Non-Volatile Storage
33602   STG: Storage medium is corrupt   Non-Volatile Storage
33603   STG: Storage medium is full   Non-Volatile Storage
33604   STG: More than one type of non-volatile storage medium specified   Non-Volatile Storage
33605   STG: Invalid Subsystem Number specified for Key   Non-Volatile Storage
33606   STG: Invalid Private Key Number specified for Key   Non-Volatile Storage
33607   STG: End of NVS storage found   Non-Volatile Storage
33608   STG: Storage Medium was recovered from backup   Non-Volatile Storage
33609   STG: Access to STG Subsystem was Blocked   Non-Volatile Storage
33610   STG: Invalid function parameter passed to an STG API function   Non-Volatile Storage
33611   STG: Duplicate Key(s) present in NVS   Non-Volatile Storage
33612   STG: The type of NVS specified does not exist in this product.   Non-Volatile Storage
33613   STG: Attempted to write past the end of a STG RAM search table   Non-Volatile Storage
33614   STG: The specified configuration code is invalid   Non-Volatile Storage
33615   STG: The specified Nvs medium is not supported by the called function   Non-Volatile Storage
33616   STG: Configuration failed   Non-Volatile Storage
33617   STG: Storage medium is not initialized, it cannot be used   Non-Volatile Storage
33618   STG: Storage medium is corrupt, it cannot be used   Non-Volatile Storage
33619   STG: Storage medium is corrupt - key data checksum failed   Non-Volatile Storage
33620   STG: Storage medium is corrupt - key storage control block checksum failed   Non-Volatile Storage
33621   STG: Storage medium is corrupt - initialized values not set   Non-Volatile Storage
33622   STG: Invalid storage partition   Non-Volatile Storage
33623   STG: Invalid storage granularity   Non-Volatile Storage
33624   STG: Cannot recover NVS medium, only one partition available   Non-Volatile Storage
33700   MON: Diagnostic NT pipe to SVCHOST is not created   Monitor
33701   MON: undefined error for monitor command   Monitor
33702   MON: Failed to create a line editor component   Monitor
33703   MON: The line editor has disabled forwarding to the terminal   Monitor
33900   ERR: Description not found   Error Handling
33901   ERR: Too many error groups defined   Error Handling
33903   ERR: No error descriptor partitions left   Error Handling
33904   ERR: Test: <test string pointer> <test decimal value 16-bit integer> <test string pointer> <test pseudo float value (32-bit integer> <test string pointer> <test long 32-bit unsigned integer> <test string pointer> <test 16-bit hexadecimal value>   Error Handling
33905   ERR: Error group is invalid   Error Handling
33906   ERR: Error parameter overflow   Error Handling
33907   ERR: Firmware integrity failure   Error Handling
33908   ERR: Parameterized error table is full, all indexes are reserved   Error Handling
33909   ERR: Error buffer has overrun   Error Handling
33910   ERR: Error buffer is invalid   Error Handling
34000   PRM: Invalid function parameter(s) sent into API function   Parameter
34001   PRM: Invalid parameter group identifier   Parameter
34002   PRM: Duplicate registration of parameter group table   Parameter
34003   PRM: Invalid parameter group table   Parameter
34004   PRM: Duplicate parameter key found   Parameter
34005   PRM: Invalid parameter key   Parameter
34006   PRM: The search is complete   Parameter
34007   PRM: The buffer size specified does not match buffer size for NVS parameter key   Parameter
34008   PRM: The specified group description has not been found   Parameter
34009   PRM: The parameter has not been found   Parameter
34010   PRM: The parameter copy index is invalid   Parameter
34011   PRM: The parameter element index is invalid   Parameter
34012   PRM: The parameter syntax is invalid   Parameter
34013   PRM: The parameter range is invalid (name="<Name of offending parameter>" key=<Key of offending parameter>)   Parameter
34014   PRM: The string parameter syntax is not supported   Parameter
34015   PRM: The string parameter length is invalid   Parameter
34016   PRM: Unexpected software failure   Parameter
34017   PRM: The functionality has not been implemented   Parameter
34018   PRM: The PRM command is in progress   Parameter
34019   PRM: No parameter table was registered for this group   Parameter
34020   PRM: A zero is sent as the DataLength function parameter   Parameter
34021   PRM: The PRM internal data buffer size is too small   Parameter
34022   PRM: No more available overflow system table entries   Parameter
34023   PRM: The group descriptions are inconsistent   Parameter
34024   PRM: The NVS system table is corrupt   Parameter
34025   PRM: NVS medium is corrupt   Parameter
34026   PRM: STG subsystem General failure   Parameter
34027   PRM: The NVS medium is full   Parameter
34028   PRM: A STG key already exist with a different data block size   Parameter
34029   PRM: Parameter key not found in NVS   Parameter
34030   PRM: No default is associated with parameter   Parameter
34031   PRM: No NVS is detected   Parameter
34032   PRM: Parameter subsystem is not initialized   Parameter
34033   PRM: Cannot modify parameter, not in configuration mode   Parameter
34034   PRM: Cannot modify parameter, not in media mode   Parameter
34035   PRM: The specified configuration code is invalid   Parameter
34036   PRM: Configuration failed.   Parameter
34037   PRM: Command cancelled   Parameter
34038   PRM: This parameter is read-only   Parameter
34039   PRM: Restricted parameter, insufficient access level   Parameter
34040   PRM: This parameter is not accessible from the diagnostic monitor   Parameter
34041   PRM: Parameter '<Group name><Index reference> <Short name><Element name>' changed from <Original value> to <New value> <Units>   Parameter
34101   UTL: no saved records in history table   Utility Functions
34102   UTL: invalid parameter   Utility Functions
34103   UTL: pipe handle is invalid   Utility Functions
34104   UTL: pipe is now full   Utility Functions
34105   UTL: pipe is now empty   Utility Functions
34106   UTL: data pipe could not be created   Utility Functions
34107   UTL: data pipe could not be deleted   Utility Functions
34108   UTL: Reached the end of a linear link list   Utility Functions
34109   UTL: Memory Allocation Failure   Utility Functions
34110   UTL: The pipe information has not registered   Utility Functions
34111   UTL: Pipe is opened   Utility Functions
34112   UTL: Connecting NT pipe   Utility Functions
34113   UTL: Pipe not connected, cannot retrieve pipe name   Utility Functions
34114   UTL: Failed to create and connect NT Pipe   Utility Functions
34115   UTL: The destination pipe id is invalid   Utility Functions
34116   UTL: The source pipe id is invalid   Utility Functions
34117   UTL: The buffer to hold PipeName is too small   Utility Functions
34118   UTL: Failed to read from NT pipe   Utility Functions
34119   UTL: Sending too much data through an NT pipe   Utility Functions
34120   UTL: Cannot disable interrupts when performing link list index search   Utility Functions
34121   UTL: Conversion failed, software error   Utility Functions
34122   UTL: No data is ready in the specified queue   Utility Functions
34123   UTL: Cannot read from the board's IIC port   Utility Functions
34124   UTL: Cannot write to the board's IIC port   Utility Functions
34125   UTL: Fixed-size queue full   Utility Functions
34126   UTL: Fixed-size queue empty   Utility Functions
34127   UTL: Invalid format type for conversion   Utility Functions
34128   UTL: Invalid engineering units for conversion   Utility Functions
34129   UTL: Attempted to register too many override function tables   Utility Functions
34130   UTL: Attempted to override the same function more than once   Utility Functions
34131   UTL: Cannot override function because function cannot be found   Utility Functions
34132   UTL: Cannot override function because override table not registered   Utility Functions
34133   UTL: Attempt to register override table or override function after system initialization   Utility Functions
34200   BCM: invalid port ID specified   Binary Communication Protocol
34201   BCM: internal buffer space full   Binary Communication Protocol
34202   BCM: timeout waiting for ACK   Binary Communication Protocol
34203   BCM: general failure   Binary Communication Protocol
34204   BCM: internal buffers exhausted   Binary Communication Protocol
34205   BCM: HDLC CRC receiver error   Binary Communication Protocol
34206   BCM: failure to create WIN32 thread   Binary Communication Protocol
34207   BCM: client receive buffer too small   Binary Communication Protocol
34208   BCM: received HDLC pkt not for us   Binary Communication Protocol
34209   BCM: port is in 'Raw' mode   Binary Communication Protocol
34210   BCM: can't send, no Carrier Detect   Binary Communication Protocol
34211   BCM: timer thread create failure   Binary Communication Protocol
34212   BCM: out of virtual connection buffers   Binary Communication Protocol
34213   BCM: virtual connection was lost   Binary Communication Protocol
34214   BCM: no more internal HDLC buffers   Binary Communication Protocol
34215   BCM: transmit timeout multiplex error   Binary Communication Protocol
34216   BCM: no multiplex communications occuring   Binary Communication Protocol
34217   BCM: The BCM_PORT is not of type NT Pipe   Binary Communication Protocol
34218   BCM: Invalid function parameter detected   Binary Communication Protocol
34219   BCM: The pipe information has not registered   Binary Communication Protocol
34220   BCM: Pipe is opened   Binary Communication Protocol
34221   BCM: Connecting NT pipe   Binary Communication Protocol
34222   BCM: Pipe not connected, cannot retrieve pipe name   Binary Communication Protocol
34223   BCM: Failed to create and connect NT Pipe   Binary Communication Protocol
34224   BCM: The destination pipe id is invalid   Binary Communication Protocol
34225   BCM: The source pipe id is invalid   Binary Communication Protocol
34226   BCM: The buffer to hold PipeName is too small   Binary Communication Protocol
34227   BCM: Failed to read from NT pipe   Binary Communication Protocol
34228   BCM: The specified BCM port is not opened   Binary Communication Protocol
34229   BCM: Sending too much data through an NT pipe   Binary Communication Protocol
34230   BCM: Baud Rate specified is too high   Binary Communication Protocol
34231   BCM: Invalid Baud rate   Binary Communication Protocol
34232   BCM: Transaction List Underflow   Binary Communication Protocol
34233   BCM: HDLC Address Invalid or Unknown   Binary Communication Protocol
34234   BCM: DOP Address Invalid or Unknown   Binary Communication Protocol
34235   BCM: DNE-ICE Auto ID failure   Binary Communication Protocol
34236   BCM: DNE-ICE Communication setup failure   Binary Communication Protocol
34237   BCM: DNE-ICE Communication shutdown failure   Binary Communication Protocol
34238   BCM: DNE-ICE connection failure   Binary Communication Protocol
34239   BCM: DNE: receive timout failure on ICE data   Binary Communication Protocol
34240   BCM: Transmission Cancelled   Binary Communication Protocol
34241   BCM: Can't open W32 serial Port   Binary Communication Protocol
34242   BCM: Can't initialize comm port buffers in Win32   Binary Communication Protocol
34243   BCM: Access attempted to unsupported port in Win32   Binary Communication Protocol
34244   BCM: Error while closing port   Binary Communication Protocol
34245   BCM: Error while writing to port   Binary Communication Protocol
34301   DPC: undefined pattern number   Data Path Control
34302   DPC: close of closed scan   Data Path Control
34303   DPC: close of un-open scan   Data Path Control
34304   DPC: write to undefined scan   Data Path Control
34305   DPC: call with NULL pattern struct   Data Path Control
34306   DPC: Too many cells in pattern   Data Path Control
34307   DPC: Pattern write call error   Data Path Control
34308   DPC: write to un-opened scan   Data Path Control
34309   DPC: write to closed scan   Data Path Control
34310   DPC: open of NULL scan   Data Path Control
34311   DPC: memory overflow   Data Path Control
34312   DPC: too many scans   Data Path Control
34313   DPC: timed out waiting for stripe to complete   Data Path Control
34320   DPC: SCSI Driver Error, line <Line Number>   Data Path Control
34321   DPC: SCSI driver error, invalid initiator   Data Path Control
34322   DPC: SCSI asynchronous transfer requested, line <Line Number>   Data Path Control
34323   DPC: SCSI parity error detected   Data Path Control
34324   DPC: SCSI bus reset detected   Data Path Control
34331   DPC: orthog slope smaller than minimum, check plate rotation   Data Path Control
34332   DPC: orthog slope larger than max, check plate rotation   Data Path Control
34333   DPC: OCCT SDRAM Test fail - Address = <Address>, Write data = <Write data>, Read data = <Read data>   Data Path Control
34334   DPC: SDRAM module was not detected   Data Path Control
34335   DPC: RIP resolution is invalid   Data Path Control
34336   DPC: Pixels per stroke is invalid   Data Path Control
34337   DPC: Subscan duplicate is invalid   Data Path Control
34338   DPC: Mainscan duplicate is invalid   Data Path Control
34339   DPC: Drum diameter is invalid   Data Path Control
34340   DPC: Mainscan length is invalid   Data Path Control
34341   DPC: Mainscan length is not a multiple of 32   Data Path Control
34342   DPC: Pixels per stroke is not a multiple of 8   Data Path Control
34343   DPC: DPC subsystem received unknown command message   Data Path Control
34344   DPC: Stroke width not a multiple of subscan replication   Data Path Control
34345   DPC: Reserved Error Code 1   Data Path Control
34346   DPC: Reserved Error Code 1   Data Path Control
34350   DPC: Data transfer already in progress   Data Path Control
34351   DPC: Data transfer not in progress   Data Path Control
34352   DPC: memory test not defined   Data Path Control
34353   DPC: memory test failed at address   Data Path Control
34354   DPC: too much data has been received   Data Path Control
34355   DPC: too little data has been received   Data Path Control
34356   DPC: Data channel not detected   Data Path Control
34357   DPC: Datapath operation was preempted   Data Path Control
34358   DPC: Image padding limit was exceeded   Data Path Control
34359   DPC: No blank regions available for use   Data Path Control
34360   DPC: No blank regions currently being used   Data Path Control
34361   DPC: Invalid OCCT pointer send to datapath   Data Path Control
34400   NUC: Function called with invalid function parameters   Nucleus RTOS Additional Support
34401   NUC: No such option token is found   Nucleus RTOS Additional Support
34402   NUC: Option found, but no parameter value is defined   Nucleus RTOS Additional Support
34403   NUC: Parameter buffer is too small   Nucleus RTOS Additional Support
34404   NUC: The option token to search is too long   Nucleus RTOS Additional Support
34405   NUC: Table is too small to hold all memory map entries   Nucleus RTOS Additional Support
34800   RIF: Image property parameter not found in list   Recorder Interface
34801   RIF: Image property list is invalid   Recorder Interface
34802   RIF: Image property type is invalid   Recorder Interface
34803   RIF: Message type is invalid   Recorder Interface
34805   RIF: Cannot merge image property lists   Recorder Interface
34810   RIF: Received invalid command code from workstation   Recorder Interface
34811   RIF: Received invalid parameter from workstation   Recorder Interface
34812   RIF: Command code received from workstation is not supported   Recorder Interface
34813   RIF: Received non-zero value in reserved field from workstation   Recorder Interface
34820   RIF: No more resolutions supported   Recorder Interface
34821   RIF: Resolution mode not defined   Recorder Interface
34822   RIF: Invalid resolution specified   Recorder Interface
34823   RIF: No more media supported   Recorder Interface
34855   RIF: Too many timestamps in timing loop-back packet   Recorder Interface
34856   RIF: Cannot timestamp a non timing loop-back packet   Recorder Interface
34857   RIF: Signifies that the packet represents a timing loop-back   Recorder Interface
34858   RIF: The input function parameter is incorrect   Recorder Interface
34900   RTL: failure   Routing Layer
34901   RTL: no free transactions   Routing Layer
34902   RTL: no match   Routing Layer
34903   RTL: full   Routing Layer
34904   RTL: addressing conflict   Routing Layer
34905   RTL: no route found   Routing Layer
34906   RTL: timeout   Routing Layer
34907   RTL: port not opened   Routing Layer
34908   RTL: NT COM port or pipe conflict   Routing Layer
34909   RTL: Invalid Source Id String   Routing Layer
34910   RTL: Invalid Destination Id String   Routing Layer
34911   RTL: Cannot determine which DNE instance to connect to   Routing Layer
34912   RTL: RTL transaction has already been freed   Routing Layer
34913   RTL: No Communications to Target Device   Routing Layer
34914   RTL: Route buffer is reserved by non-streaming messages   Routing Layer
34915   RTL: The indexed RTL transaction is invalid   Routing Layer
34916   RTL: Invalid CDI communication profile   Routing Layer
34917   RTL: BCM port cannot be opened   Routing Layer
34918   RTL: Linked List Protection Semaphore Fault   Routing Layer
34919   RTL: Transaction flushed from RTL list   Routing Layer
35001   DNE: Failed to create heartbeat timer   Datanode Electronics Hardware
35002   DNE: Failed to disable heartbeat timer   Datanode Electronics Hardware
35003   DNE: Failed to reset heartbeat timer   Datanode Electronics Hardware
35004   DNE: Invalid print unit number received   Datanode Electronics Hardware
35005   DNE: <ICE name> not detected   Datanode Electronics Hardware
35006   DNE: <DNE name> is out of range (<Lower range limit> to <Upper range limit><Temperature unit>)   Datanode Electronics Hardware
35200   _360: reset induced by software watchdog   Motorola 68360 Microprocessor
35201   _360: reset induced by halt monitor   Motorola 68360 Microprocessor
35202   _360: reset induced by loss of clock   Motorola 68360 Microprocessor
35701   PRD: value returned is invalid   Product Support
35702   PRD: unable to find subsystem name   Product Support
35703   PRD: unable to find specified record   Product Support
35704   PRD: unable to allocate memory   Product Support
35705   PRD: unable to return freed memory   Product Support
35706   PRD: unable to find specified subsystem number   Product Support
35707   PRD: called function is not applicable for this product   Product Support
35708   PRD: version information has already been registered   Product Support
35709   PRD: version information has not been registered yet   Product Support
35710   PRD: The run-time option specified does not exist   Product Support
35711   PRD: Could not save the run-time option setting to NVS   Product Support
35712   PRD: Flyoff occurred, remove media   Product Support
35713   PRD: Flyoff sensor blocked, check machine for loose media, or check flyoff sensor   Product Support
35714   PRD: Roller down, cannot move nor spin the drum   Product Support
35715   PRD: Registration pins are down, cannot move the drum   Product Support
35718   PRD: Trailing edge backbone is down, cannot move or spin the drum   Product Support
35719   PRD: Bender is up, cannot plot if the bender is up   Product Support
35720   PRD: Safety sense is not on, check doors and emergency off switch   Product Support
35721   PRD: Safety override switch is on, cannot plot with override on   Product Support
35722   PRD: Media partially loaded on drum, cannot move nor spin drum   Product Support
35724   PRD: Emergency stop switch is on   Product Support
35725   PRD: Missing the head cable, cannot plot if there is no head cable   Product Support
35726   PRD: Missing the head power cable, cannot plot if there is no power to the head   Product Support
35727   PRD: Head safety loop broken, check machine   Product Support
35728   PRD: No write laser power, make sure doors are shut, and emergency stop switches are not depressed   Product Support
35729   PRD: Drum brake did not turn off properly   Product Support
35731   PRD: Fans did not go on   Product Support
35732   PRD: Coolant pump did not go on   Product Support
35733   PRD: Front panel is open, check front panel   Product Support
35734   PRD: A door on the home side is not on, check home side   Product Support
35735   PRD: Back panel not detected, check back panel   Product Support
35736   PRD: A door on the away side is not on, check away side   Product Support
35737   PRD: No instance number is available for this product   Product Support
35738   PRD: Cannot unlock doors if the drum is spinning   Product Support
35739   PRD: Cannot unlock doors if the machine is not idle   Product Support
35741   PRD: Invalid Temperature Reading Attempted   Product Support
35742   PRD: Drum brake override is on, cannot spin drum   Product Support
35743   PRD: Invalid NVS key in callback   Product Support
35744   PRD: The write laser could not be turned on because the safe line is not high   Product Support
35745   PRD: The write laser relay did not activate as asked, it may be welded   Product Support
35746   PRD: The drum amp relay did not activate as asked, it may be welded   Product Support
35747   PRD: The main power relay did not activate as asked, it may be welded   Product Support
35748   PRD: System Presence Fault: <Presence detect bit description> (<Presence detect bit name>) Not Detected   Product Support
35749   PRD: System Input Fault: <Input bit description> (<Input bit name>) In Unexpected State   Product Support
35750   PRD: System Output Fault: <Output bit description> (<Output bit name>) In Unexpected State   Product Support
35751   PRD: System Range Fault: <Analog bit description> (<Analog bit name>) Out Of Range: Low=<Low range limit>, High=<High range limit>, Reading=<Current value>   Product Support
35752   PRD: System Range Warning: <Analog bit description> (<Analog bit name>) Out Of Range: Low=<Low range limit>, High=<High range limit>, Reading=<Current value>   Product Support
35753   PRD: Debris removal currently not support by this product   Product Support
35754   PRD: All faults cleared   Product Support
35756   PRD: Drum is spinning when a stationary drum is expected   Product Support
35757   PRD: Hardware can't generate requested tach simulation velocity   Product Support
35758   PRD: Leading edge backbone is down, cannot move the drum   Product Support
35759   PRD: Plate door is open, cannot spin the drum or enable laser   Product Support
35760   PRD: head logic power not enabled, cannot plot   Product Support
35761   PRD: the specification is invalid or the specified component does not exist   Product Support
35762   PRD: the callback associated with the component is invalid   Product Support
35763   PRD: could not access information for the specified component   Product Support
35764   PRD: the run-time state specified does not exist   Product Support
35765   PRD: the run-time state could not be set to the required state   Product Support
35766   PRD: Invalid model configuration specified   Product Support
35767   PRD: Ramp is in near the drum, cannot spin the drum   Product Support
35769   PRD: Spectrum vacuum roller (VR) is up against the drum, cannot move nor spin the drum   Product Support
35770   PRD: Spectrum cleaning roller (CR) is up against the drum, cannot move nor spin the drum   Product Support
35771   PRD: Incompatible workstation SCSI interface. LVD-SCSI required.   Product Support
35772   PRD: System Pressure Out of Range: Reading=<Low range limit>, Low=<High range limit>, High=<Current value> (<Analog group name>)   Product Support
35773   PRD: Top panels not detected, check top panels   Product Support
35774   PRD: Top door is open, check top door   Product Support
35775   PRD: Fanbox panel is not detected, check fanbox panel   Product Support
35776   PRD: Invalid safety array entry specified   Product Support
35777   PRD: Fatal error triggered   Product Support
35778   PRD: Invalid callback   Product Support
35779   PRD: User issued an abort, use 'abort clear' to clear the abort   Product Support
35780   PRD: <Group name> Presence Fault: <Presence detect bit description> (<Presence detect bit name>) Not Detected   Product Support
35781   PRD: <Group name> Input Fault: <Input bit description> (<Input bit name>) In Unexpected State   Product Support
35782   PRD: <Group name> Output Fault: <Output bit description> (<Output bit name>) In Unexpected State   Product Support
35783   PRD: <Group name> Range Fault: <Analog bit description> (<Analog bit name>) Out Of Range: Reading=<Current value>, Low=<Low range limit>, High=<High range limit>   Product Support
35784   PRD: <Group name> Range Warning: <Analog bit description> (<Analog bit name>) Out Of Range: Reading=<Current value>, Low=<Low range limit>, High=<High range limit>   Product Support
35785   PRD: <Group name>: All faults cleared   Product Support
35786   PRD: Front panel is unlocked   Product Support
35787   PRD: Away Side Balance actuator extended, cannot spin the drum   Product Support
35788   PRD: Home Side Balance actuator extended, cannot spin the drum   Product Support
35789   PRD: Media detected on the load ramp, cannot spin drum. Please remove media from the ramp   Product Support
35790   PRD: Model code is invalid or unavailable   Product Support
35791   PRD: Limit tag is not specified in the limit table   Product Support
35792   PRD: Invalid optional value found. Limit tag [<Limit Tag>]. Value <Optional Value>.   Product Support
35793   PRD: <Limit description> is <Limit value> <Unit>. <Parameter> <Unit> exceeds the limit.   Product Support
35794   PRD: <Limit description> is <Limit value> <Unit>. <Parameter> <Unit> is lower than the minimum.   Product Support
35795   PRD: <Limit description> must be <Limit State>.   Product Support
35796   PRD: <Limit description> do not contain option flag <Option flag>. Cannot enable the option.   Product Support
35797   PRD: <Limit description> is <Limit value> <Unit>. <Parameter> <Unit> is not equal to the limit.   Product Support
35798   PRD: Key switch is on, drum speed limited to <Drum Speed> RPM   Product Support
35799   PRD: The hood is open, check the hood   Product Support
35800   _376: reset induced by software watchdog   68376 Microprocessor
35801   _376: reset induced by halt monitor   68376 Microprocessor
35802   _376: reset induced by RESET opcode   68376 Microprocessor
35803   _376: reset cause unknown   68376 Microprocessor
35804   _376: reset triggered by crash dump handler   68376 Microprocessor
36001   VBS: specified subsystem number is not registered   Verbose Message Filtering
36002   VBS: specified output device is not applicable for this product   Verbose Message Filtering
36200   URT: invalid serial port ID specified   Uart
36201   URT: serial port not opened yet   Uart
36202   URT: pipe access failed; pipe may be full (TX) or empty (RX)   Uart
36203   URT: illegal option specified   Uart
36204   URT: UART disabled   Uart
36501   BRD: Internal Error - Failed to create a Nucleus PLUS Timer   Board abstraction
36502   BRD: Internal Error - Failed to control a Nucleus PLUS Timer   Board abstraction
36503   BRD: Internal Error - Failed to Reset a Nucleus PLUS Timer   Board abstraction
36504   BRD: Flash Driver code does not support this command primitive   Board abstraction
36505   BRD: Flash Driver code has failed to program flash memory   Board abstraction
36506   BRD: Flash Driver code has failed to erase a flash sector   Board abstraction
36507   BRD: Insufficient memory to hold assembler flash driver routines   Board abstraction
36508   BRD: The flash memory write operation failed to verify   Board abstraction
36509   BRD: The address specified does not point to flash memory   Board abstraction
36510   BRD: No Xilinx (LCA) was found in flash memory   Board abstraction
36511   BRD: Undefined error   Board abstraction
36512   BRD: Undefined error   Board abstraction
36513   BRD: Board temperature sensor initialization failed   Board abstraction
36514   BRD: No Overwriting pattern file (OVWR) was found in flash memory   Board abstraction
36800   HLT: DNE not initialized (set DNE init 1)   Firmware Health
36801   HLT: Invalid Parameters Sent to HLT Function   Firmware Health
36802   HLT: Requested element is not registered   Firmware Health
36803   HLT: Requested subsystem is not registered   Firmware Health
36804   HLT: Internal HLT Subsystem Error   Firmware Health
36805   HLT: A Subsystem has timed out   Firmware Health
36806   HLT: Subsystem reported with unrecoverable error   Firmware Health
36807   HLT: No cable detected between DNE and ICE   Firmware Health
36808   HLT: BCM comm. between DNE and ICE has stopped   Firmware Health
36809   HLT: The specified print unit is currently offline   Firmware Health
36810   HLT: No Subsystem has reported in yet   Firmware Health
36811   HLT: The system/subsystem is starting up   Firmware Health
36812   HLT: Subsystem shutdown is currently taking place   Firmware Health
36813   HLT: HLT subsystem has not initialized   Firmware Health
36814   HLT: Workstation is not detected   Firmware Health
36815   HLT: Feature is not available yet   Firmware Health
36816   HLT: Firmware resource is low   Firmware Health
36817   HLT: Print unit is online, connection checking not done   Firmware Health
36818   HLT: SCSI Disk has errors   Firmware Health
36819   HLT: SCSI disk not detected   Firmware Health
36820   HLT: End of list detected   Firmware Health
36821   HLT: Board temperature is above threshold   Firmware Health
36822   HLT: Board temperature is above maximum limit   Firmware Health
36900   MCE: Insufficient Heap Memory - required for DF1 serial drivers   Master Control Electronics
36901   MCE: WMD Subsystem RCON Incoming Command Register Failure   Master Control Electronics
36902   MCE: SDRAM Operation Failure   Master Control Electronics
37200   HIF: A parameter to an internal function is invalid   Head Interface
37201   HIF: Timeout waiting for the write laser   Head Interface
37202   HIF: Timeout waiting for the focus   Head Interface
37203   HIF: The length of the monitor command is invalid   Head Interface
37204   HIF: Unexpected software failure   Head Interface
37250   HIF: Received unexpected message   Head Interface
37251   HIF: Head firmware download failed   Head Interface
37252   HIF: Datalink not in programming mode, command not valid   Head Interface
37253   HIF: Datalink in programming mode, command not valid   Head Interface
37254   HIF: Datalink already in programming mode   Head Interface
37255   HIF: Datalink timed out waiting for break   Head Interface
37256   HIF: break detected, exposure head has reset   Head Interface
37257   HIF: internal message timeout   Head Interface
37258   HIF: format error detected during data transfer   Head Interface
37259   HIF: sumcheck error detected during data transfer   Head Interface
37260   HIF: datalink programming sequence taking too long   Head Interface
37261   HIF: cannot perform requested operation, no LOADER present   Head Interface
37262   HIF: failed to respond to programming command   Head Interface
37263   HIF: Timeout while waiting for the exposure head to complete response string   Head Interface
37264   HIF: ENQQ expected and not received   Head Interface
37265   HIF: ACK expected and not received   Head Interface
37266   HIF: incorrect response length   Head Interface
37267   HIF: incorrect version response   Head Interface
37268   HIF: incorrect response data   Head Interface
37269   HIF: binary download resource allocation failure   Head Interface
37270   HIF: binary download timeout waiting for user   Head Interface
37271   HIF: binary download loader failed   Head Interface
37420   PHS: TH2 error [<error code>] <error string>   Parallel Head
37701   DRS: software error   Drum Servo
37702   DRS: Drum operation timed out   Drum Servo
37703   DRS: Drum is reserved, command ignored   Drum Servo
37704   DRS: Overflow in internal drum calculation   Drum Servo
37705   DRS: Tach simulator preventing drum servo control   Drum Servo
37706   DRS: The current drum command has been preempted   Drum Servo
37707   DRS: Drum servo control missing interrupts   Drum Servo
37708   DRS: Specified drum velocity out of range   Drum Servo
37709   DRS: Drum Hardware Missing <Description of the faulted hardware component>   Drum Servo
37710   DRS: Drum Position Counter Overflow   Drum Servo
37711   DRS: Specified Drum Torque out of range   Drum Servo
37712   DRS: Drum Position Not Settling   Drum Servo
37713   DRS: Drum Velocity Exceeded 100 Rpm in Torque mode   Drum Servo
37714   DRS: Drum Velocity Error Exceeded   Drum Servo
37715   DRS: Drum can't move to position at zero velocity   Drum Servo
37716   DRS: Drum failed to reach position   Drum Servo
37717   DRS: Number of allowable drum callbacks exceeded   Drum Servo
37718   DRS: Drum target velocity invalid for PLL calculations   Drum Servo
37719   DRS: Drum parameter patch range error: <Name of the drum NVS parameter that can not be patched because>   Drum Servo
37720   DRS: Drum command passed an invalid pointer parameter   Drum Servo
37721   DRS: Drum cannot use an encoder resolution of 0   Drum Servo
37722   DRS: Drum can't stop at position when not moving   Drum Servo
37723   DRS: Operation blocked while drum is freewheeling   Drum Servo
37801   LCA: Xilinx LCA program failed   Xilinx Abstraction Layer
37802   LCA: Xilinx LCA file not found   Xilinx Abstraction Layer
37803   LCA: Xilinx LCA file checksum error   Xilinx Abstraction Layer
37804   LCA: LCA interrupt failed to register callback properly   Xilinx Abstraction Layer
37805   LCA: Feature not supported by the Xilinx firmware   Xilinx Abstraction Layer
37806   LCA: Invalid Latch ID specified   Xilinx Abstraction Layer
37807   LCA: Xilinx configuration failed   Xilinx Abstraction Layer
37808   LCA: SDRAM operation failed   Xilinx Abstraction Layer
37809   LCA: Overwriting pattern verification failed   Xilinx Abstraction Layer
37810   LCA: Invalid Overwriting Pattern detected   Xilinx Abstraction Layer
37811   LCA: Hardware can't generate requested tach simulation velocity   Xilinx Abstraction Layer
37812   LCA: <Feature> requires at least Xilinx v<Major version number>.<Minor version number>, current Xilinx is v<Major version number2>.<Minor version number2>   Xilinx Abstraction Layer
37813   LCA: Overwriting pattern <PatternID> is not licensed on this device   Xilinx Abstraction Layer
38101   MPC: Plot has been aborted   Main Plot Control
38102   MPC: Plot Mode is out of range or not valid   Main Plot Control
38103   MPC: Media Type is out of range or not valid   Main Plot Control
38104   MPC: Not configured for <Mainscan resolution> by <Subscan resolution> DPI resolution   Main Plot Control
38105   MPC: Startscan delay <Startscan delay> sub-pixels must be at least zero   Main Plot Control
38106   MPC: Total startscan delay <Startscan delay> sub-pixels is too large   Main Plot Control
38107   MPC: Mainscan image size <Mainscan image size> pixels too large, maximum is <Maximum image size> pixels   Main Plot Control
38108   MPC: Could not find edge of media after <Search attempts> attempts   Main Plot Control
38109   MPC: Head not configured for '<Media name>/<Media colour>/' media   Main Plot Control
38110   MPC: The carriage start position <Carriage start position> mm is beyond the home tab   Main Plot Control
38111   MPC: Timeout waiting for image data   Main Plot Control
38112   MPC: No more media supported   Main Plot Control
38113   MPC: No resolution modes configured   Main Plot Control
38114   MPC: Timeout balancing stroke   Main Plot Control
38115   MPC: Invalid plot parameter ('<Parameter name>' = <Parameter value>)   Main Plot Control
38116   MPC: No valid edge found, check edge detect strip   Main Plot Control
38117   MPC: Internal: Invalid parameter passed to function   Main Plot Control
38118   MPC: Internal: System resource unavailable   Main Plot Control
38119   MPC: Midpoint position <Midpoint position> um too small for subscan media size   Main Plot Control
38120   MPC: Phase Lock Loop losing lock   Main Plot Control
38121   MPC: Debris removal not running as expected   Main Plot Control
38122   MPC: The '<Sequence name>' sequence is currently being processed   Main Plot Control
38123   MPC: The Phase Lock Loop could not be started   Main Plot Control
38124   MPC: The Phase Lock Loop cannot accommodate <Mainscan resolution> DPI   Main Plot Control
38125   MPC: The drum speed is too high for imaging, maximum is <Maximum drum speed> RPM   Main Plot Control
38126   MPC: The Xilinx firmware must be upgraded   Main Plot Control
38127   MPC: Mainscan image size <Mainscan image size> pixels must equal gapless drum circumference <Drum circumference> pixels   Main Plot Control
38128   MPC: Mainscan shift <Mainscan image shift> um larger than gapless drum circumference   Main Plot Control
38129   MPC: The specified sequence is not supported   Main Plot Control
38130   MPC: The pattern stroke width (<Pattern stroke width>) must equal the head (<Head stroke width>)   Main Plot Control
38131   MPC: Registration pins <First pin> and <Second pin> are configured incorrectly   Main Plot Control
38132   MPC: Media not on <Registration pin> registration pin   Main Plot Control
38133   MPC: An error occurred during plotting on the slave   Main Plot Control
38134   MPC: Multiple plates detected on drum   Main Plot Control
38135   MPC: The media is positioned incorrectly along the drum   Main Plot Control
38136   MPC: Subscan output resolution of <Subscan output resolution> DPI must equal head resolution   Main Plot Control
38137   MPC: Invalid imaging drum speed attempted   Main Plot Control
38138   MPC: Invalid media stack identifier <Media Stack Identifier> specified   Main Plot Control
38139   MPC: Cancel ignored, no sequence in progress   Main Plot Control
38140   MPC: Proofing option is not enabled   Main Plot Control
38141   MPC: The proof carrier is not positioned correctly or is not the correct size   Main Plot Control
38142   MPC: Subscan image size <Subscan image size> pixels too large, maximum is <Maximum image size> pixels   Main Plot Control
38143   MPC: Internal: Expected plot sequence is not active   Main Plot Control
38144   MPC: The carriage end position <End position> mm is beyond the maximum travel distance <Maximum carriage travel> mm   Main Plot Control
38145   MPC: The media is sensitive to retraces and one or more retraces occurred   Main Plot Control
38146   MPC: Forced failure   Main Plot Control
38147   MPC: Head is not yet initialized   Main Plot Control
38148   MPC: Xilinx version <Current major version>.<Current minor version> is invalid, must be at least <Minimum required major version>.<Minimum required minor version>   Main Plot Control
38149   MPC: The head model installed is incompatible with this machine   Main Plot Control
38150   MPC: Image data sent to the head was possibly corrupted. Check plate for artifacts   Main Plot Control
38151   MPC: Invalid media type (<Media type>) for this operation   Main Plot Control
38152   MPC: Total amount of clamp shadow is too large   Main Plot Control
38153   MPC: Slave head resolution: <Head resolution on the slave board> DPI does not match with the one on the master: <Head resolution on the master board> DPI   Main Plot Control
38154   MPC: Slave head swath width: <Head swath width on the slave board> does not match with the one on the master: <Head swath width on the master board>   Main Plot Control
38155   MPC: Overwriting not allowed with pixel replication   Main Plot Control
38156   MPC: Specified thickness of gapless media must be 0   Main Plot Control
38157   MPC: Cannot start an image, the '<System name>' is busy   Main Plot Control
38158   MPC: Timed out waiting for plot engine to initialize   Main Plot Control
38159   MPC: Communication failed between master and slave MCE boards   Main Plot Control
38160   MPC: Overwriting not allowed with positive media   Main Plot Control
38161   MPC: The Phase Lock Loop did not stabilize   Main Plot Control
38162   MPC: Target sample was out of tolerance   Main Plot Control
38163   MPC: Could not find target   Main Plot Control
38164   MPC: Not configured for <Subscan resolution> DPI subscan resolution   Main Plot Control
38165   MPC: Variable mainscan resolution is not supported   Main Plot Control
38166   MPC: Carriage position is wrong - carriage has probably stalled   Main Plot Control
38167   MPC: <Head name> image is outside of the head's range (position <The position that triggered the error> um)   Main Plot Control
38168   MPC: Could not find seam after <Number of attempts> attempts   Main Plot Control
38169   MPC: Seam could not be verified for fine search   Main Plot Control
38170   MPC: Seam not found using fine search   Main Plot Control
38171   MPC: Raster image data received from workstation was possibly corrupted. Check plate for artifacts   Main Plot Control
38172   MPC: Timed out waiting for raster image data CRC from workstation   Main Plot Control
38173   MPC: All heads are currently disabled   Main Plot Control
38174   MPC: Media too small (subscan) to image in portrait registration mode   Main Plot Control
38175   MPC: Media too large (subscan) to image in portrait registration mode   Main Plot Control
38176   MPC: Swath width is invalid, extra scanlines <Extra scanlines for current media> >= stroke width <Head stroke width>   Main Plot Control
38177   MPC: Media subscan size <Media Subscan Size> um is too long for registration pin configuration   Main Plot Control
38178   MPC: Portrait media rotation (<Rotation>) too large   Main Plot Control
38179   MPC: The media is in an invalid position, it is extending over the drum midpoint   Main Plot Control
38180   MPC: Slave error buffer overflow, unable to read slave error   Main Plot Control
38181   MPC: Plotting speed <Calculated carriage speed> mm/sec (<Pixels advanced per drum rotation> PPR at <Drum speed> RPM) exceeds licensed limit of <Carriage speed limit>   Main Plot Control
38182   MPC: The '<Parameter name>' parameter is set to 0   Main Plot Control
38183   MPC: Drum speed <Target drum speed> is too fast for <Target resolution> DPI resolution, maximum is <Maximum drum speed> RPM   Main Plot Control
38184   MPC: The media type '<Media name>' is not currently allowed on this device   Main Plot Control
38185   MPC: Current stroke width of <Current Stroke Width> is greater than allowed maximum of <Maximum Licensed Stroke Width>   Main Plot Control
38186   MPC: Workstation Fault [<Image error code>] <Image error text>   Main Plot Control
38187   MPC: Measured diameter different from expected: Measured (<Diameter measured>) - Expected (<Diameter expected>)   Main Plot Control
38188   MPC: '<Sequence table>', sequence '<Sequence>' (<Sequence address>), failure action <Failure action> not found   Main Plot Control
38189   MPC: ExtraScanlines and StrokeWidth set incorrectly for the yaw test pattern   Main Plot Control
38190   MPC: Phase Lock Loop possibly losing lock, error = <Phase error microns> microns (<Phase error clock cycles> clock cycles)   Main Plot Control
38191   MPC: The head unexpectedly reset   Main Plot Control
38192   MPC: The <Plate identifier> is positioned <Error distance> mm too close to the <Error direction> side   Main Plot Control
38193   MPC: The <Plate identifier> is positioned too close to the <Error direction> side   Main Plot Control
38194   MPC: The write laser is stuck calibrating   Main Plot Control
38195   MPC: The gc mainscan shift is too small   Main Plot Control
38196   MPC: Media subscan size <Media subscan size> mm cannot fit on the registration pins   Main Plot Control
38197   MPC: The head is over the media at the minimum edge search position   Main Plot Control
38200   MIC: Error message with no error code   Main Image Control
38201   MIC: Software error   Main Image Control
38202   MIC: No image tasks available   Main Image Control
38203   MIC: Image task is not active   Main Image Control
38204   MIC: Image task is busy   Main Image Control
38205   MIC: Image task is not suspended   Main Image Control
38206   MIC: Image parameter is missing   Main Image Control
38207   MIC: Image parameter is invalid   Main Image Control
38208   MIC: Currently not initialized, waiting for FLUSH   Main Image Control
38209   MIC: Flush is not complete   Main Image Control
38210   MIC: Image parameters already received   Main Image Control
38211   MIC: Too many image tasks requested   Main Image Control
38212   MIC: Already unloading media   Main Image Control
38213   MIC: Image cancelled by flush   Main Image Control
38214   MIC: Cannot free unreserved image task   Main Image Control
38215   MIC: Invalid image task identifier   Main Image Control
38216   MIC: Cannot free busy image task   Main Image Control
38217   MIC: Cannot free busy image task   Main Image Control
38218   MIC: Fatal error   Main Image Control
38219   MIC: Software error: <Additional information on the software error>   Main Image Control
38220   MIC: Command aborted   Main Image Control
38221   MIC: Task specified is not a valid image task   Main Image Control
38222   MIC: Task specified cannot be cancelled   Main Image Control
38223   MIC: Task has error, but a second error has occurred   Main Image Control
38224   MIC: Image task specified is not a valid image (or not currently running)   Main Image Control
38225   MIC: Task specified could not be found (no matching state machine)   Main Image Control
38226   MIC: Task cancelled   Main Image Control
38227   MIC: Task has not completed   Main Image Control
38228   MIC: Flush not currently active   Main Image Control
38229   MIC: Group index not in valid range   Main Image Control
38230   MIC: Group image index not in valid range   Main Image Control
38231   MIC: Group not valid, no images   Main Image Control
38232   MIC: Invalid callback supplied   Main Image Control
38233   MIC: Invalid image status structure supplied   Main Image Control
38234   MIC: Invalid flush status structure supplied   Main Image Control
38235   MIC: Invalid task parameter structure   Main Image Control
38236   MIC: Invalid image parameter structure   Main Image Control
38237   MIC: Invalid image list array supplied   Main Image Control
38238   MIC: Invalid state type received in message   Main Image Control
38239   MIC: Invalid command ID in command msg   Main Image Control
38240   MIC: No state machines available   Main Image Control
38241   MIC: State machine not found (no magic number match)   Main Image Control
38242   MIC: State machines pointer invalid   Main Image Control
38243   MIC: Message invalid, cannot parse   Main Image Control
38244   MIC: Conditional false - internal only   Main Image Control
38245   MIC: Invalid media type structure   Main Image Control
38246   MIC: Media instance not being used by MIC   Main Image Control
38301   MDS: Software error   Media Scheduler
38302   MDS: Software error, unable to allocate sequence data structure   Media Scheduler
38303   MDS: Software error, the Scheduler is trying to use a NULL sequence data struct   Media Scheduler
38304   MDS: Software error, the Scheduler is trying to use a invalid sequence structure pool   Media Scheduler
38305   MDS: Software error, the Scheduler is trying to use a invalid sequence structure linked list   Media Scheduler
38306   MDS: Software error, the Scheduler could not remove the sequence structure from the linked list   Media Scheduler
38307   MDS: Software error, unable to allocate media data structure   Media Scheduler
38308   MDS: Software error, the Scheduler is trying to use a NULL media data structure   Media Scheduler
38309   MDS: Software error, the Scheduler is trying to use a invalid media structure pool   Media Scheduler
38310   MDS: Software error, the Scheduler is trying to use a invalid media structure linked list   Media Scheduler
38311   MDS: Software error, the Scheduler could not remove the media structure from the linked list   Media Scheduler
38312   MDS: Software error, unable to allocate arguments data structure   Media Scheduler
38313   MDS: Software error, the Scheduler is trying to use a NULL arguments data structure   Media Scheduler
38314   MDS: Software error, the Scheduler is trying to use a invalid arguments structure pool   Media Scheduler
38315   MDS: Cancel command failed, Scheduler not currently processing any operation with specified media instance   Media Scheduler
38316   MDS: Scheduler could not schedule command since it did not have a proper arguments   Media Scheduler
38317   MDS: Image type specified is not supported by this machine   Media Scheduler
38318   MDS: Scheduler monitor command failed   Media Scheduler
38319   MDS: Initialization failed use 'resume' to re-attempt initialization   Media Scheduler
38320   MDS: Scheduler command aborted   Media Scheduler
38321   MDS: Scheduler command cancelled   Media Scheduler
38322   MDS: Software error, suspend button not defined   Media Scheduler
38323   MDS: No <media name> on the drum to unload   Media Scheduler
38324   MDS: Scheduler cannot cancel unload commands   Media Scheduler
38325   MDS: Cannot cancel initialization commands   Media Scheduler
38326   MDS: Cannot eject during an unload   Media Scheduler
38327   MDS: Cannot eject media during initialization   Media Scheduler
38328   MDS: Scheduler sequence is in an unknown state   Media Scheduler
38329   MDS: The <Media name> on the drum is already being unloaded   Media Scheduler
38330   MDS: Scheduler has no tasks currently suspended   Media Scheduler
38331   MDS: Software error, Scheduler received a bad Media Hander task ID in it callback   Media Scheduler
38332   MDS: Software error, Scheduler received an invalid action type when setting up its arrays   Media Scheduler
38333   MDS: Invalid parameter sent to monitor command   Media Scheduler
38334   MDS: Media already on drum, cannot force new media on drum   Media Scheduler
38335   MDS: The parameter 'media stacks' is not used, only 1 stack available   Media Scheduler
38336   MDS: The parameter 'bay' is not used, no bays are available on this device   Media Scheduler
38337   MDS: The parameter 'punch' is not used, no punches are available on this device   Media Scheduler
38338   MDS: The parameter 'exit' is not used, only one exit on this device   Media Scheduler
38339   MDS: Attempt to load proofing media without carrier or receiver on drum   Media Scheduler
38340   MDS: Media scheduler fatal error   Media Scheduler
38341   MDS: Media type argument is invalid, media type = <Media type value that is invalid>   Media Scheduler
38342   MDS: Media stacks argument is <Current media stack value>, maximum = <Maximum media stack value>   Media Scheduler
38343   MDS: Media stacks argument cannot be 0, must be 1 or greater   Media Scheduler
38344   MDS: Bay argument cannot be 0 for an automatic job   Media Scheduler
38345   MDS: Bay argument is <current bay argument>, maximum is <maximum number of bays>   Media Scheduler
38346   MDS: Bay argument is <current bay argument>, but it is a manual job so it should be 0   Media Scheduler
38347   MDS: Punch argument is <current punch argument>, maximum is <maximum number of punches>   Media Scheduler
38348   MDS: Exit argument is <current exit argument>, maximum is <maximum number of exits>   Media Scheduler
38349   MDS: Rotate argument is <current rotate argument>, rotator is not supported   Media Scheduler
38350   MDS: Image side argument is invalid, must be set to a defined value for this media   Media Scheduler
38351   MDS: Image side argument is not valid for this media, must be set to Side A   Media Scheduler
38352   MDS: Image side argument is greater than expected, set to a valid value   Media Scheduler
38353   MDS: Default load arguments have been reset to valid values   Media Scheduler
38354   MDS: Default unload arguments have been reset to valid values   Media Scheduler
38355   MDS: Invalid media instance, 0 is not a valid media instance   Media Scheduler
38356   MDS: Invalid media instance, does not match media on the drum   Media Scheduler
38357   MDS: Requested media is not loaded   Media Scheduler
38358   MDS: Stack locations specified for <number of stack locations specified> stack(s), however <number of stacks being loaded> stack(s) are being loaded   Media Scheduler
38359   MDS: Cannot unload <media type> since it is still being loaded (possibly suspended)   Media Scheduler
38360   MDS: Cannot unload <media type> since <media being loaded on top> is being loaded on top   Media Scheduler
38361   MDS: Cannot unload <media type> since <media name(s) on top> is/are loaded on top   Media Scheduler
38362   MDS: Media Scheduler operation is undefined   Media Scheduler
38363   MDS: Media Scheduler <Operation Sequence Type> operation (<Media Instance ID>) cannot be run because the Media Handler is not initialized   Media Scheduler
38364   MDS: Media Scheduler <Operation Sequence Type> operation (<Media Instance ID>) is not allowed to be cancelled   Media Scheduler
38365   MDS: Media Scheduler <Operation Sequence Type> operation (<Media Instance ID>) could not schedule cycle testing operations (error:<Error code>)   Media Scheduler
38366   MDS: Media Scheduler operation <Media Instance ID> has an unknown sequence type <Sequence Type>   Media Scheduler
38367   MDS: Media Scheduler <Operation Sequence Type> operation (<Media Instance ID>) could not find a sequence to run   Media Scheduler
38368   MDS: Media Scheduler could not find step Id <Step Id> in sequence   Media Scheduler
38369   MDS: Media Scheduler <Operation Sequence Type> operation (<Media Instance ID>) could not find synchronization step Id <Step Id> in sequence (process Id:<Process Id>)   Media Scheduler
38370   MDS: Media Scheduler could not find end step in sequence   Media Scheduler
38371   MDS: Media Scheduler step tracking is undefined   Media Scheduler
38372   MDS: Media Scheduler <Operation Sequence Type> operation <Media Instance ID> has reached its maximum step count <Maximum Step Count> for step Id <Step Id> (process Id<Process Id>)   Media Scheduler
38373   MDS: Media Scheduler <Operation Sequence Type> operation <Media Instance ID> has an undefined process   Media Scheduler
38374   MDS: Media Scheduler <Operation Sequence Type> operation <Media Instance ID> could not start a new process (maximum of <Max process count>)   Media Scheduler
38375   MDS: Media Scheduler <Operation Sequence Type> operation <Media Instance ID> could not find process <Process Id>   Media Scheduler
38376   MDS: Media Scheduler could not finish sequence scan, too many steps (maximum <Maximum number of scan steps>)   Media Scheduler
38377   MDS: Media Scheduler could not schedule bay close since the bay is not open   Media Scheduler
38378   MDS: Media Scheduler could not schedule bay close since one was already scheduled   Media Scheduler
38379   MDS: Media Scheduler decision type is not supported for step type   Media Scheduler
38380   MDS: Too many alternate bays, maximum is <Maximum number of alternative bays>   Media Scheduler
38381   MDS: The media type '<Media name>' is not currently allowed on this device   Media Scheduler
38400   NET: TRECK TCP/IP Stack is reporting a Fatal Error condition   NET Support
38401   NET: Failure to activate SLIP link-layer protocol   NET Support
38402   NET: Failure to activate PPP Server link-layer protocol   NET Support
38403   NET: Failure to activate PPP Client link-layer protocol   NET Support
38404   NET: Failure to activate EtherNet link-layer protocol   NET Support
38405   NET: Failure to allocate internal memory - FATAL   NET Support
38406   NET: Failure to add a device driver to TRECK TCP/IP Stack - FATAL   NET Support
38407   NET: Failure to open a device driver for the TRECK TCP/IP Stack - FATAL   NET Support
38408   NET: Interface device driver for the TRECK TCP/IP Stack is not open   NET Support
38409   NET: Failure to query information about a h/w interface in the TRECK TCP/IP Stack - FATAL   NET Support
38410   NET: Warning in TRECK function <Function name>: <Warning description>\n   NET Support
38601   STP: Unable to write velocity, not in Host Velocity Control Mode   Stepper Motor
38602   STP: Attempt to read or write an invalid parameter   Stepper Motor
38603   STP: Attempt to write an invalid configuration flag   Stepper Motor
38604   STP: Attempt to write an invalid configuration mode   Stepper Motor
38605   STP: Attempt to write a stepper motor parameter that is out of range   Stepper Motor
38606   STP: Attempt to change the parameters of the system while the motor is moving   Stepper Motor
38607   STP: Trajectory queue address out of range   Stepper Motor
38608   STP: Motor does not exist on this board   Stepper Motor
38609   STP: Stepper hardware status check has failed   Stepper Motor
38610   STP: The Stepper Firmware has not been properly initialized   Stepper Motor
38611   STP: Stepper controller is awaiting an unsolicited message acknowledge   Stepper Motor
38800   WMD: Out of command/prompt/stream handles   Workstation Message Dispatch
38801   WMD: Invalid handle   Workstation Message Dispatch
38802   WMD: Internal error detected   Workstation Message Dispatch
38803   WMD: Solicitor number is currently used   Workstation Message Dispatch
38804   WMD: Command Table Full   Workstation Message Dispatch
38805   WMD: Prompt Descriptor Table Full   Workstation Message Dispatch
38806   WMD: Too many buttons for prompt   Workstation Message Dispatch
38807   WMD: An invalid button code was used   Workstation Message Dispatch
38808   WMD: An invalid prompt ID was used   Workstation Message Dispatch
38809   WMD: Illegal attempt to access prompt object   Workstation Message Dispatch
38810   WMD: Unsupported Workstation protocol   Workstation Message Dispatch
38811   WMD: Device is running\nUNSUPPORTED\nEngineering Firmware   Workstation Message Dispatch
38812   WMD: Invalid Command Code detected   Workstation Message Dispatch
38813   WMD: socket() call has failed   Workstation Message Dispatch
38814   WMD: bind() call has failed   Workstation Message Dispatch
38815   WMD: listen() call has failed   Workstation Message Dispatch
38816   WMD: accept() call has failed   Workstation Message Dispatch
38817   WMD: recv() call has failed   Workstation Message Dispatch
38818   WMD: send() call has failed   Workstation Message Dispatch
38819   WMD: WSAStartup() call has failed   Workstation Message Dispatch
38820   WMD: ioctlsocket() call has failed   Workstation Message Dispatch
38821   WMD: Command is rejected because of service lockout   Workstation Message Dispatch
38822   WMD: Service lockout   Workstation Message Dispatch
38823   WMD: No socket connection with workstation.   Workstation Message Dispatch
38824   WMD: Invalid data unit size RCON parameter in Read Memory or Write Memory command   Workstation Message Dispatch
38825   WMD: Too many workstation status change callbacks have been registered   Workstation Message Dispatch
38826   WMD: The RCON connection to the workstation has been lost   Workstation Message Dispatch
38827   WMD: Workstation is not detected   Workstation Message Dispatch
38828   WMD: Too many workstation command received callbacks have been registered   Workstation Message Dispatch
39000   SAT: The board type is unknown   SAT Board
39101   SIF: SIF/SCON General Failure   SCON Interface
39102   SIF: Received an SCON NAK reply   SCON Interface
39103   SIF: SCON Operation timed out   SCON Interface
39104   SIF: No Free CAN Transmit Buffers available   SCON Interface
39105   SIF: The SIF Subsystem has detected a reentrancy attempt   SCON Interface
39106   SIF: The SIF Subsystem has not been initialized properly   SCON Interface
39107   SIF: The SIF Subsystem has run out of queue buffers   SCON Interface
39108   SIF: SIF Serial port Open has failed due to not being activated for SIF serial support   SCON Interface
39200   SFW: Unknown I/O Type found in I/O Table   Satellite I/O Board Firmware
39201   SFW: Internal Memory Allocation Error   Satellite I/O Board Firmware
39202   SFW: Failure Registering Virtual Register Handler with SIF subsystem   Satellite I/O Board Firmware
39203   SFW: Failure Registering Broadcast Handler with SIF Subsystem   Satellite I/O Board Firmware
39204   SFW: Could not locate Firmware Control Register Set in ram   Satellite I/O Board Firmware
39205   SFW: Failure Erasing a Flash Memory Sector   Satellite I/O Board Firmware
39206   SFW: Could not locate One Wire Bus Virtual Register Set in ram   Satellite I/O Board Firmware
39207   SFW: Eeprom NVS parameter is not present   Satellite I/O Board Firmware
39208   SFW: Eeprom NVS Bad CRC Value found - corrupt NVS medium   Satellite I/O Board Firmware
39209   SFW: Eeprom NVS medium is blank   Satellite I/O Board Firmware
39210   SFW: Eeprom NVS - unsupported storage method   Satellite I/O Board Firmware
39211   SFW: Eeprom Erase Failure   Satellite I/O Board Firmware
39212   SFW: Eeprom Write Failure   Satellite I/O Board Firmware
39213   SFW: Eeprom Read Failure   Satellite I/O Board Firmware
39214   SFW: Eeprom Parameter (Index) Failure - too big   Satellite I/O Board Firmware
39215   SFW: Internal Firmware Failure   Satellite I/O Board Firmware
39216   SFW: Safety Relay Failure [Drum Brake]   Satellite I/O Board Firmware
39217   SFW: Safety Relay Failure [PS2]   Satellite I/O Board Firmware
39218   SFW: Safety Relay Failure [PS3]   Satellite I/O Board Firmware
39219   SFW: Safety Relay Failure [AC Safe Spare]   Satellite I/O Board Firmware
39220   SFW: Safety Relay Failure [Drum Amp]   Satellite I/O Board Firmware
39221   SFW: Safety Relay Failure [SAT]   Satellite I/O Board Firmware
39222   SFW: Safety Relay Failure [PS6]   Satellite I/O Board Firmware
39301   SIO: SIO General Failure   SCON Master Support
39302   SIO: Failure to Register with SIF   SCON Master Support
39303   SIO: SAT I/O Node does not exist   SCON Master Support
39304   SIO: The Unsolicited Callback Information Block has Become Corrupted   SCON Master Support
39305   SIO: The Call Back Function Specified is Invalid   SCON Master Support
39306   SIO: Attempt to register too many callbacks with the SIO subsystem   SCON Master Support
39307   SIO: All SCON Connection resources are in use - no more left   SCON Master Support
39400   GIM: Invalid Image ID   General Image Management
39401   GIM: Image not complete   General Image Management
39402   GIM: Internal firmware error   General Image Management
39403   GIM: Invalid Image Parameter   General Image Management
39404   GIM: Please load a new plate   General Image Management
39405   GIM: Please unload the ejected media   General Image Management
39406   GIM: Required data was locked by another subsystem   General Image Management
39407   GIM: Not ready for Flush End command   General Image Management
39408   GIM: No flush active that can be ended.   General Image Management
39409   GIM: Invalid Flush state detected   General Image Management
39410   GIM: Device is unlocked   General Image Management
39411   GIM: Head not initialized: not ready for query   General Image Management
39412   GIM: Unrecoverable Flush Failure. Device must be reset.   General Image Management
39413   GIM: Invalid Image Task ID detected   General Image Management
39414   GIM: Invalid bay number detected   General Image Management
39415   GIM: WARNING: Bypassed functionality detected   General Image Management
39416   GIM: Drum command received while drum is busy   General Image Management
39417   GIM: Carriage command received while carriage is busy   General Image Management
39418   GIM: Invalid carriage velocity value attempted   General Image Management
39419   GIM: Invalid carriage position value attempted   General Image Management
39420   GIM: Invalid latch number   General Image Management
39421   GIM: Invalid sensor number   General Image Management
39422   GIM: Invalid latch value code   General Image Management
39423   GIM: Invalid Status type specified   General Image Management
39424   GIM: Unexpected Command   General Image Management
39425   GIM: IO Name Identifier too long   General Image Management
39426   GIM: Incorrect number of IO Data bytes   General Image Management
39427   GIM: Flush is required before operation permitted.   General Image Management
39428   GIM: Can not process RCON command, not initialized   General Image Management
39429   GIM: RCON command received while busy   General Image Management
39430   GIM: Invalid Group ID   General Image Management
39432   GIM: Too many images in Group   General Image Management
39433   GIM: No group available   General Image Management
39434   GIM: The device cannot support the number of stacks queried   General Image Management
39435   GIM: Suspend queue is full, cannot handle any more suspends   General Image Management
39436   GIM: Suspend could not be found, not removed   General Image Management
39437   GIM: Please load carrier   General Image Management
39438   GIM: Please unload the ejected carrier   General Image Management
39439   GIM: Invalid group parameter   General Image Management
39440   GIM: Please load receiver   General Image Management
39441   GIM: Please load donor   General Image Management
39442   GIM: RCON command is missing argument '<Name of the missing parameter name>'   General Image Management
39443   GIM: Invalid RCON variable argument specified '<Name of the invalid argument name>'   General Image Management
39444   GIM: Unknown or invalid property ID specified   General Image Management
39445   GIM: Invalid operation attempted on property '<Name of the DCAPI property could not be manipulated>'   General Image Management
39446   GIM: Timeout accessing property information   General Image Management
39447   GIM: Media Name length (<Name of the media setting that is too long (either name, or>) exceeded maximum length of <The maximum number of characters that can be used> characters   General Image Management
39448   GIM: RCON media instance is unknown or invalid   General Image Management
39449   GIM: The system is attempting to simultaneously access too many media instances   General Image Management
39450   GIM: No media is available. Requested media operation cannot be performed.   General Image Management
39451   GIM: Property Not supported   General Image Management
39452   GIM: Invalid arguments specified in Set Seam Geometry request   General Image Management
39453   GIM: Prompt array full, cannot make new prompt   General Image Management
39454   GIM: Could not find prompt   General Image Management
39455   GIM: Workstation command locked out   General Image Management
39456   GIM: Image Raster Data error detected (CRC). Check plate for artifacts!   General Image Management
39457   GIM: Invalid or unsupported combination of arguments   General Image Management
39458   GIM: Service move command received while device is processing a previous move command   General Image Management
39459   GIM: The imaged area is not yet available for reading   General Image Management
39460   GIM: The Preloader is loading the bay   General Image Management
39461   GIM: Please load a new plate on the home side   General Image Management
39462   GIM: Please load a new plate on the away side   General Image Management
39463   GIM: Please load a new plate in the center   General Image Management
39464   GIM: Please load two new plates   General Image Management
39465   GIM: Status Handler table full   General Image Management
39466   GIM: Workstation watchdog timed out. Shutting down all systems.   General Image Management
39467   GIM: Bay transfer operation still in progress   General Image Management
39468   GIM: No bay transfer operation in progress   General Image Management
39469   GIM: Bay media configurations must match for transfer   General Image Management
39470   GIM: Automatic Pallet Loader (APL) is unlocked   General Image Management
39471   GIM: Invalid arguments specified in Set Punch Regions request   General Image Management
39472   GIM: Not enough free Media Handler descriptors to start a new Media Handler operation   General Image Management
39473   GIM: Media Handler operation specified could not be found   General Image Management
39501   IOS: software error   I/O Scanner
39502   IOS: Insufficient memory to create IO scanner tables   I/O Scanner
39503   IOS: I/O Bit not found in product table   I/O Scanner
39504   IOS: I/O Group not found in product table   I/O Scanner
39505   IOS: Event group pointer is null   I/O Scanner
39506   IOS: Can't assign non-input bit to event group   I/O Scanner
39507   IOS: IO values are not initialized   I/O Scanner
39508   IOS: Bypass not allowed on this I/O   I/O Scanner
39509   IOS: No remote address for requested bit   I/O Scanner
39510   IOS: No remote address for requested bit   I/O Scanner
39511   IOS: Invalid IOS mode   I/O Scanner
39512   IOS: IO Name Identifier too long   I/O Scanner
39513   IOS: Incorrect number of IO Data bytes   I/O Scanner
39514   IOS: Workstation command locked out   I/O Scanner
39515   IOS: Conversion function not available   I/O Scanner
39516   IOS: Callback table full   I/O Scanner
39517   IOS: Bit handle already has an event registered   I/O Scanner
39518   IOS: Satellite board address <The satellite board ID that is not responding> register <The register address being accessed> not responding   I/O Scanner
39519   IOS: TCP/IP failure   I/O Scanner
39800   SST: Invalid API Function Parameter Detected   System Status
39801   SST: Internal SST error   System Status
39802   SST: Invalid SST handle   System Status
39803   SST: Status group not registered   System Status
39804   SST: Invalid SST I/O type   System Status
39805   SST: Specified I/O not found   System Status
39806   SST: Invalid upper and lower thresholds for analog I/O   System Status
39807   SST: Invalid digital target value   System Status
39808   SST: Invalid I/O failure priority level   System Status
39809   SST: System is not in initialization mode   System Status
39900   MBT: Fatal Error - Fell out of Monitor code   MCE Boot Firmware
39901   MBT: Fatal Error - Boot Code is Corrupt   MCE Boot Firmware
39902   MBT: Fatal Error - Insufficient Heap Memory available   MCE Boot Firmware
40001   SMC: Software error   Stepper Motor Control
40002   SMC: CAN communication error   Stepper Motor Control
40003   SMC: Cannot issue command, motor is moving [<Name of the stepper motor>]   Stepper Motor Control
40004   SMC: Cannot issue command, motor is being controlled by another process and is reserved [<Name of the stepper motor>]   Stepper Motor Control
40005   SMC: Motor number out of range or the motor is not configured on this device   Stepper Motor Control
40006   SMC: Invalid trajectory queue address specified [<Name of the stepper motor>]   Stepper Motor Control
40007   SMC: Invalid parameter specified [<Name of the stepper motor>]   Stepper Motor Control
40008   SMC: Invalid velocity value specified [<Name of the stepper motor>]   Stepper Motor Control
40009   SMC: Invalid acceleration value specified [<Name of the stepper motor>]   Stepper Motor Control
40010   SMC: Invalid micro step rate specified [<Name of the stepper motor>]   Stepper Motor Control
40011   SMC: Invalid current specified [<Name of the stepper motor>]   Stepper Motor Control
40012   SMC: Invalid direction mode parameter specified [<Name of the stepper motor>]   Stepper Motor Control
40013   SMC: Remote hardware is not processing motor commands [<Name of the stepper motor>]   Stepper Motor Control
40014   SMC: Stepper motor name not found   Stepper Motor Control
40015   SMC: Motor unexpectedly hit the home sensor [<Name of the stepper motor>]   Stepper Motor Control
40016   SMC: Motor unexpectedly hit the away sensor [<Name of the stepper motor>]   Stepper Motor Control
40017   SMC: Stepper command timed out [<Name of the stepper motor>]   Stepper Motor Control
40018   SMC: The remote board hardware status check has failed [<Name of the stepper motor>]   Stepper Motor Control
40019   SMC: Invalid motor gain parameter specified [<Name of the stepper motor>]   Stepper Motor Control
40020   SMC: Motor initialization has failed [<Name of the stepper motor>]   Stepper Motor Control
40021   SMC: Remote motor has not been initialized [<Name of the stepper motor>]   Stepper Motor Control
40022   SMC: Invalid update mode parameter specified [<Name of the stepper motor>]   Stepper Motor Control
40023   SMC: Invalid position specified [<Name of the stepper motor>]   Stepper Motor Control
40024   SMC: Invalid steps per real unit specified [<Name of the stepper motor>]   Stepper Motor Control
40025   SMC: Invalid distance specified [<Name of the stepper motor>]   Stepper Motor Control
40026   SMC: Invalid initialization parameters specified [<Name of the stepper motor>]   Stepper Motor Control
40027   SMC: Command failed, the shared motor is using all the remote bandwidth [<Name of the stepper motor>]   Stepper Motor Control
40028   SMC: Invalid initialization dual stepper mode specified [<Name of the stepper motor>]   Stepper Motor Control
40029   SMC: Move command preempted   Stepper Motor Control
40030   SMC: Failed to detect 48V [<Name of the stepper motor>]   Stepper Motor Control
40031   SMC: Failed to detect alternate sensor cable [<Name of the stepper motor>]   Stepper Motor Control
40032   SMC: Failed to detect home and away cable [<Name of the stepper motor>]   Stepper Motor Control
40033   SMC: Failed to detect power cable [<Name of the stepper motor>]   Stepper Motor Control
40034   SMC: Failed to detect data cable [<Name of the stepper motor>]   Stepper Motor Control
40035   SMC: Over current fault detected [<Name of the stepper motor>]   Stepper Motor Control
40036   SMC: Over temperature fault detected [<Name of the stepper motor>]   Stepper Motor Control
40037   SMC: Under voltage fault detected [<Name of the stepper motor>]   Stepper Motor Control
40038   SMC: Driver fault detected [<Name of the stepper motor>]   Stepper Motor Control
40039   SMC: Failed to detect the cable [<Name of the stepper motor>]   Stepper Motor Control
40040   SMC: Brake override detected [<Name of the stepper motor>]   Stepper Motor Control
40041   SMC: Invalid maximum jerk value specified [<Name of the stepper motor>]   Stepper Motor Control
40042   SMC: Input value is outside the limits [<Name of the stepper motor>]   Stepper Motor Control
40043   SMC: Satellite board has reset, stepper control has failed [<Name of the stepper motor>]   Stepper Motor Control
40044   SMC: Velocity of <Velocity specified in real units/s> units/s [<Velocity specified in steps/s> steps/s] is too high, max is <Maximum velocity allowed in real units/s> units/s [<Maximum velocity allowed in steps/s> steps/s] [<Name of the stepper motor>]   Stepper Motor Control
40045   SMC: Velocity of <Velocity specified in real units/s> units/s [<Velocity specified in steps/s> steps/s]is too low, min is <Minimum velocity allowed in real units/s> units/s [<Minimum velocity allowed in steps/s> steps/s] [<Name of the stepper motor>]   Stepper Motor Control
40046   SMC: Motor already has a reset callback [<Name of the stepper motor>]   Stepper Motor Control
40047   SMC: Satellite board does not support quarter current mode [<Name of the stepper motor>]   Stepper Motor Control
40048   SMC: The motor has been stopped before the motor has started [<Name of the stepper motor>]   Stepper Motor Control
40049   SMC: Remote motor is waiting for an acknowledge [<Name of the stepper motor>]   Stepper Motor Control
40050   SMC: Remote motor has failed with an undefined error <The undefined error> [<Name of the stepper motor>]   Stepper Motor Control
40100   SBT: Fatal Error - Fell out of Monitor code   Satellite Board Boot Firmware
40101   SBT: Fatal Error - Boot Code is Corrupt   Satellite Board Boot Firmware
40102   SBT: Fatal Error - Insufficient Heap Memory available   Satellite Board Boot Firmware
40103   SBT: Fatal Error - Failure Registering VR Handler with SIF   Satellite Board Boot Firmware
40104   SBT: Fatal Error - Failure Registering Broadcast Handler with SIF   Satellite Board Boot Firmware
40105   SBT: Warning - Failure to Erase a Flash Sector   Satellite Board Boot Firmware
40200   MDH: <motor name> stepper motor has already started the command, cannot start it again   Media Handler
40201   MDH: Software error. Media Handler error occurred, but error has no error code.   Media Handler
40202   MDH: Software error. Suspend received a invalid suspend button type.   Media Handler
40203   MDH: Software error. Media Handler received an unrecognized command.   Media Handler
40204   MDH: Software error. No callback function supplied to Media Handler   Media Handler
40205   MDH: Software error. Media Handler did not receive the proper number of command arguments.   Media Handler
40206   MDH: Command Failed. Media Handler already running another task.   Media Handler
40207   MDH: Cannot cancel command. Media Handler task is not currently executing any commands.   Media Handler
40208   MDH: Media handler task is currently suspended.   Media Handler
40209   MDH: Media handler is not currently suspended.   Media Handler
40210   MDH: Media Handler is not initialized.   Media Handler
40211   MDH: Media ejected, process cancelled   Media Handler
40212   MDH: Media Handler task cancelled   Media Handler
40213   MDH: Media released from the drum and removed from the machine.   Media Handler
40214   MDH: Forced failure.   Media Handler
40215   MDH: Init cancelled, use RESUME to re-initialize.   Media Handler
40216   MDH: Cannot enable/disable cycletest mode when machine not idle.   Media Handler
40217   MDH: Cannot enable/disable 'plateless' operation when machine not idle.   Media Handler
40218   MDH: Operation not complete (vacuum clamp option not installed).   Media Handler
40219   MDH: Operation not complete (bender option is installed)   Media Handler
40220   MDH: Operation not complete (machine options not setup)   Media Handler
40221   MDH: Operation not complete (non-contact registration option not installed)   Media Handler
40222   MDH: Operation not complete (contact registration option not installed)   Media Handler
40223   MDH: Operation not complete (balancer option not installed)   Media Handler
40224   MDH: Operation not complete (registration options are installed)   Media Handler
40225   MDH: Operation not complete (punch option not installed)   Media Handler
40226   MDH: Software error. Monitor command default error.   Media Handler
40227   MDH: Unsupported media handler argument(s), unable to execute media handling sequences.   Media Handler
40228   MDH: Media Handler task aborted   Media Handler
40229   MDH: Media released, remove media and use RESUME to continue   Media Handler
40230   MDH: Invalid actuator timeout (must be non-zero)   Media Handler
40231   MDH: <motor name> stepper motor cannot search for a sensor [<I/O name>] if waiting is not specified   Media Handler
40232   MDH: No Calibration array for the image/load type   Media Handler
40233   MDH: Media Handler does not support RELEASE for the media type specified   Media Handler
40234   MDH: Media Handler does not support 'Auto Calibration' for the media type specified   Media Handler
40235   MDH: Media Handler does not support 'bay open' array for the media type specified   Media Handler
40236   MDH: Operation not complete (Spectrum proof option not installed)   Media Handler
40237   MDH: <motor name> stepper motor recieved an invalid setup parameter   Media Handler
40238   MDH: <motor name> stepper motor has not started a command, cannot wait for it to complete   Media Handler
40239   MDH: Software Error. The error code contains the wrong number of parameters   Media Handler
40240   MDH: Fatal error   Media Handler
40241   MDH: Proof released, remove donor and receiver and use RESUME to continue   Media Handler
40242   MDH: Could not set the media on the drum   Media Handler
40243   MDH: <motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]   Media Handler
40244   MDH: Stepper motor cannot search for a sensor that has been disabled [<I/O name>]   Media Handler
40245   MDH: Command cannot be cancelled   Media Handler
40246   MDH: Media released, remove media and use MEDIA REMOVED to continue   Media Handler
40247   MDH: Software error, external command returned an invalid state message   Media Handler
40248   MDH: Software error, external command returned an invalid message type   Media Handler
40249   MDH: Software error, external command returned an invalid user argument   Media Handler
40250   MDH: Media Handler does not support service moves   Media Handler
40251   MDH: Media Handler does not support simulation option <Option>   Media Handler
40252   MDH: Media Handler does not support 'bay load' array for the media type specified   Media Handler
40253   MDH: Media Handler does not support 'bay unload' array for the media type specified   Media Handler
40254   MDH: Media handler sequence attempted to use auto-retry on step that pointed to a different step   Media Handler
40255   MDH: The <Stepper> stepper motor is losing steps (<Distance> mm)   Media Handler
40256   MDH: Unlock panels from PC and open rear hood.\nRemove any media from the engine.\nLock Panels.   Media Handler
40257   MDH: Software error. Wrong or invalid argument supplied   Media Handler
40258   MDH: Could not find step '<Step description>' in sequence   Media Handler
40259   MDH: <Motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]   Media Handler
40260   MDH: <Motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]   Media Handler
40261   MDH: <Motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]   Media Handler
40262   MDH: <Motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]   Media Handler
40263   MDH: <Motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]   Media Handler
40264   MDH: <Motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]   Media Handler
40265   MDH: <Motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]   Media Handler
40266   MDH: <Motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]   Media Handler
40267   MDH: <Motor name> stepper motor unexpectedly hit the home sensor   Media Handler
40268   MDH: <Motor name> stepper motor unexpectedly hit the home sensor   Media Handler
40269   MDH: <Motor name> stepper motor unexpectedly hit the home sensor   Media Handler
40270   MDH: <Motor name> stepper motor unexpectedly hit the home sensor   Media Handler
40271   MDH: <Motor name> stepper motor unexpectedly hit the home sensor   Media Handler
40272   MDH: <Motor name> stepper motor unexpectedly hit the home sensor   Media Handler
40273   MDH: <Motor name> stepper motor unexpectedly hit the home sensor   Media Handler
40274   MDH: <Motor name> stepper motor unexpectedly hit the home sensor   Media Handler
40275   MDH: <Motor name> stepper motor unexpectedly hit the away sensor   Media Handler
40276   MDH: <Motor name> stepper motor unexpectedly hit the away sensor   Media Handler
40277   MDH: <Motor name> stepper motor unexpectedly hit the away sensor   Media Handler
40278   MDH: <Motor name> stepper motor unexpectedly hit the away sensor   Media Handler
40279   MDH: <Motor name> stepper motor unexpectedly hit the away sensor   Media Handler
40280   MDH: <Motor name> stepper motor unexpectedly hit the away sensor   Media Handler
40281   MDH: <Motor name> stepper motor unexpectedly hit the away sensor   Media Handler
40282   MDH: <Motor name> stepper motor unexpectedly hit the away sensor   Media Handler
40283   MDH: <Motor name> stepper motor failed to respond   Media Handler
40284   MDH: <Motor name> stepper motor failed to respond   Media Handler
40285   MDH: <Motor name> stepper motor failed to respond   Media Handler
40286   MDH: <Motor name> stepper motor failed to respond   Media Handler
40287   MDH: <Motor name> stepper motor failed to respond   Media Handler
40288   MDH: <Motor name> stepper motor failed to respond   Media Handler
40289   MDH: <Motor name> stepper motor failed to respond   Media Handler
40290   MDH: <Motor name> stepper motor failed to respond   Media Handler
40291   MDH: Media Handler does not support plot preparation   Media Handler
40292   MDH: The Media Handler experienced an internal error, restart the device   Media Handler
40293   MDH: <motor name> stepper motor has not completed previous command   Media Handler
40294   MDH: <motor name> stepper motor sensor mask(s) are setup but motor is not setup to wait for completion   Media Handler
40295   MDH: Operation failed, but no error setup (device actuate)   Media Handler
40296   MDH: <motor name> stepper motor waited for <timeout in seconds> seconds, but setup command did not complete   Media Handler
40297   MDH: <sequence type> (<sequence id>) sequence is not available with these arguments   Media Handler
40298   MDH: <sequence type> (<sequence id>) sequence is not supported on this device   Media Handler
40299   MDH: Media was not detect on the <location> of the <hardware>   Media Handler
40301   MDH: Invalid bay number (bay #<Bay number>) selected   Media Handler
40302   MDH: No plates detected in bay <Bay number>   Media Handler
40303   MDH: No plates detected on plate buffer table   Media Handler
40304   MDH: Timeout waiting for the cassette interference zone to become free   Media Handler
40305   MDH: A task that did not have control over the cassette interference zone attempted to free it   Media Handler
40306   MDH: Cassette is installed but not in the pick position, the only safe position for the fetcher/picker to enter the cassette   Media Handler
40307   MDH: The cassette is not being sensed on the cart   Media Handler
40308   MDH: Cassette <Cassette Number> is not currently present in the MCU   Media Handler
40309   MDH: Cassette door open/close timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40310   MDH: Cassette lock/eject timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40311   MDH: MCU Cart lock/unlock timeout: Failed to <Action> sensor. [<I/O name>]\n Adjust the MCU cart slightly forward and backward.   Media Handler
40312   MDH: MCU move timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40313   MDH: The MCU cart was expected at the park position but not sensed there   Media Handler
40314   MDH: The MCU cart was expected at the home position but not sensed there   Media Handler
40315   MDH: The MCU cart was expected at the home or park position but not sensed there   Media Handler
40316   MDH: The MCU cart was found at both the home position and the park position (INVALID)   Media Handler
40317   MDH: Cannot move the cassette, it has not been initialized   Media Handler
40318   MDH: Invalid (non-existent) cassette number   Media Handler
40319   MDH: The MCU move failed to arrive at the target position [cassette <Cassette Number> <Position> position]   Media Handler
40320   MDH: A cassette is being sensed on the cart   Media Handler
40321   MDH: The cassette lock cylinder is not in the lock position and/or the drive is not on   Media Handler
40322   MDH: The MCU cannot lock or eject a cassette because the forks are not in the lock/eject position   Media Handler
40323   MDH: Pull the MCU cart all the way out   Media Handler
40324   MDH: Push the MCU cart all the way in   Media Handler
40325   MDH: Pull the MCU cart all the way out and remove slipsheet from top of plate   Media Handler
40326   MDH: Cassette <Cassette Number> is not being detected in the pick position, likely due to an overloaded cassette   Media Handler
40327   MDH: The MCU move failed to arrive at the target position [cassette <Cassette Number> pick position], likely due to an overloaded cassette   Media Handler
40328   MDH: Cassette validate failed. MCU pick position sensor always reading TRUE.   Media Handler
40329   MDH: Cassette validate failed. MCU pick position sensor always reading FALSE (likely broken). Device may be unusable.   Media Handler
40330   MDH: Invalid MCU ladder sensor reading. Cassette position undefined.   Media Handler
40331   MDH: Cassette <Cassette Number> is not currently installed in the MCU   Media Handler
40332   MDH: Cassette validate failed. Cassette <Cassette Number>, configured as not installed, is present in the MCU.   Media Handler
40333   MDH: Cassette validate failed. Cassette <Cassette Number>, configured as installed, is not present in the MCU.   Media Handler
40334   MDH: Cassette <Target Cassette Number> load failed. The MCU cart is already busy with cassette <Cassette Number Not Present>.   Media Handler
40335   MDH: Cassette <Target Cassette Number> unload failed. The MCU cart is already busy with cassette <Cassette Number Not Present>.   Media Handler
40336   MDH: Cassette <Target Cassette Number> SS disposal failed. The MCU cart is already busy with cassette <Cassette Number Not Present>.   Media Handler
40337   MDH: Timeout waiting for cart to arrive all the way out.   Media Handler
40338   MDH: Timeout waiting for cart to arrive all the way in.   Media Handler
40339   MDH: Cannot lock cassette <Cassette number> to MCU, it may be in an unsafe position   Media Handler
40340   MDH: Invalid cassette position sensor reading   Media Handler
40341   MDH: Bay <loader bay number> is not accessible because the preloader is docked   Media Handler
40342   MDH: Cannot move the bay hardware, it has not been initialized   Media Handler
40343   MDH: The plate cover must be open for the preloader   Media Handler
40344   MDH: Undock the preloader and remove the plate(s) from the bay, then dock the preloader again   Media Handler
40345   MDH: Please remove plate(s) from the outer bay [<I/O name>]   Media Handler
40346   MDH: The plate stack is too high to deploy the outer bay arms   Media Handler
40347   MDH: Open the cassette doors   Media Handler
40348   MDH: Pull out cassette <Cassette ID> to the load position   Media Handler
40349   MDH: Push cassette <Cassette ID> in until it latches   Media Handler
40350   MDH: Close the cassette doors   Media Handler
40351   MDH: Cassette locking pin extend timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40352   MDH: Cassette locking pin retract timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40353   MDH: <Cassette name> cannot initialize because the picker area is currently reserved by the picker   Media Handler
40354   MDH: Bay <Bay number> has changed and needs to be configured before it can be used   Media Handler
40355   MDH: Cassette <Cassette number> has a stack height of <Current stack height> mm (max <Maximum stack height> mm) remove some media from cassette   Media Handler
40356   MDH: Cassette <Cassette number> does not allow a quantity of <Quantity> for the media and slip sheet thicknesses specified. The maximum allowed is <Maximum allowable quantity> per stack   Media Handler
40357   MDH: A negative stack height of <Stack height in mm> mm was specified for cassette <Cassette number>   Media Handler
40401   MDH: Picker up/down timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40402   MDH: Picker in/out timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40403   MDH: Picker wrist timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40404   MDH: Picker vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]   Media Handler
40405   MDH: Cannot move the picker, it has not been initialized   Media Handler
40406   MDH: Plate not detected on picker   Media Handler
40407   MDH: Please remove plate detected on picker   Media Handler
40408   MDH: Please close plate cover   Media Handler
40409   MDH: Cannot move picker <Direction> because <Obstruction>   Media Handler
40410   MDH: Plates are sticking together. Please open the plate cover and separate the plates. Press RESUME to continue.   Media Handler
40411   MDH: Timeout waiting for plate cover to be opened/closed. Command cancelled   Media Handler
40412   MDH: Device ready. Close plate cover to continue.   Media Handler
40413   MDH: Picker wrist sensor is not working   Media Handler
40414   MDH: Picker wrist cylinder is faulty   Media Handler
40415   MDH: Separator arm timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40416   MDH: Cannot move separators <Direction> because <Obstruction>   Media Handler
40417   MDH: Please close plate cover, or put the preloader into position   Media Handler
40420   MDH: The Preloader is in a faulted state. Please check the Preloader display for more information   Media Handler
40421   MDH: The Preloader is not ready. It may be out of position, open, or not fully powered on   Media Handler
40422   MDH: Preloader requested for loading, but the Trendsetter is not configured properly   Media Handler
40423   MDH: The Preloader is not powered on. Please check the Preloader connections   Media Handler
40424   MDH: The Preloader is in the bay. Please check the Preloader display for more information   Media Handler
40425   MDH: The Preloader is not loading plates properly into the Trendsetter bay. Please check the Preloader display for more information   Media Handler
40426   MDH: No plates detected in the bay. The plate may not have been properly loaded by the Preloader   Media Handler
40427   MDH: Please remove all plates from the Trendsetter bay   Media Handler
40428   MDH: Loader exit door timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40429   MDH: Picker cups in/out timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40430   MDH: Cannot open exit door because an unpicked plate is detected. Please remove all plates from the plate buffer load table.   Media Handler
40450   MDH: Picker up/down timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40451   MDH: Picker slider in/out timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40452   MDH: Picker slider was expected to be out of the cassette but was not. Open panels and check for obstruction in slipsheet area   Media Handler
40453   MDH: Plenum SS sensor expected to find a plate in the cassette but found a slipsheet   Media Handler
40454   MDH: Picker was expected to be up but was not   Media Handler
40455   MDH: There is no plate detected on the picker where one was expected.\n Plates in cassette <Cassette Number> may be pinched by the side rails.   Media Handler
40456   MDH: Switchover to Bay 2 failed.   Media Handler
40457   MDH: Switchover to Bay 1 failed.   Media Handler
40458   MDH: Bay 2 full   Media Handler
40459   MDH: Picker roller home/away timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40460   MDH: Picker roller was expected to be up but was not   Media Handler
40461   MDH: Picker roller vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]   Media Handler
40462   MDH: Plenum SS sensor expected to find a slipsheet in the cassette but found a plate   Media Handler
40463   MDH: Plenum SS sensor expected to find a plate in the cassette but found a slipsheet. Check previous plate for scratches   Media Handler
40464   MDH: Slipsheet lost from picker.\nRemove any slipsheets from the slipsheet area.   Media Handler
40465   MDH: Plenum SS sensor expected to find a slipsheet in the cassette but found a plate. Slipsheet may be stuck to the underside of top plate   Media Handler
40466   MDH: Picker was expected to be down and out but was not   Media Handler
40467   MDH: Exit door was expected to be closed but was not   Media Handler
40468   MDH: Cannot move picker to <Commanded Position> mm because <Reason> (limit <Limit Position> mm)   Media Handler
40469   MDH: Picker cannot measure <Side> stack   Media Handler
40470   MDH: Picker <Side> stack measurement sensor did not settle   Media Handler
40471   MDH: Picker is at positon <Current Position> mm expected <Expected Position> mm   Media Handler
40472   MDH: Picker vacuum on timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]   Media Handler
40473   MDH: Picker vacuum off timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]   Media Handler
40474   MDH: Picker cups on timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40475   MDH: Picker cups off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40476   MDH: Picker hold down on timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40477   MDH: Picker hold down off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40478   MDH: Picker rollers on timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40479   MDH: Picker rollers off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40480   MDH: Picker cannot move because device is in override mode and picker override is not enabled   Media Handler
40481   MDH: Picker cannot move because the device override mode is off and the picker override is still enabled   Media Handler
40482   MDH: Unlock doors and remove media and/or slip sheets from the picker, also check picker volume for any dropped media   Media Handler
40483   MDH: Picker cannot initialize because the picker area is currently reserved by another task   Media Handler
40484   MDH: Picker cannot initialize because the slip sheet bin in an unknown position, unlock doors and manually push bin to a latched position   Media Handler
40485   MDH: Picker cannot initialize because the <Cassette> in an unknown position, unlock doors and manually push bin to a latched position   Media Handler
40486   MDH: Picker cassette <Cassette> calibration failed because the hold down unexpectedly detected something in the cassette   Media Handler
40487   MDH: Picker expected cassette <Cassette> to be in picker position   Media Handler
40488   MDH: Picker could not fully pick slip sheet(s), release and remove slip sheets from rollers   Media Handler
40489   MDH: Picker cannot initialize because the shuttle in an unknown position, unlock doors and manually push the shuttle so it is next to the loadtable   Media Handler
40490   MDH: Unlock doors and remove media and/or slip sheets from the picker, also check shuttle for any dropped media   Media Handler
40491   MDH: Unlock doors and remove media and/or slip sheets from the picker, also check slip sheet bin for any dropped media   Media Handler
40492   MDH: Unlock doors and remove media and/or slip sheets from the picker, also check cassettes for any dropped media   Media Handler
40493   MDH: Picker is unable to remove a single slip sheet from dual-stack job, unlock doors and manually remove the top slip sheet from active bay   Media Handler
40494   MDH: Picker was unable to measure stack(s) in cassette <Cassette>, check cassette and picker   Media Handler
40495   MDH: Picker measured a negative height of <Height> mm for the <Stack Location> in cassette <Cassette>, Recalibrate picker   Media Handler
40496   MDH: Picker did not detect a <Stack Location> in cassette <Cassette>, but did unexpectedly measure a stack height of <Height> mm. Recalibrate picker   Media Handler
40497   MDH: Picker was unable to measure stack heights in cassette <Cassette>, the maximum allowed is <Height maximum> mm. Remove some media from the cassette   Media Handler
40498   MDH: Picker measured a height of <Height> mm for the <Stack Location> in cassette <Cassette>, the maximum allowed is <Maximum Height> mm. Remove some media from the cassette   Media Handler
40499   MDH: Picker measured heights of <Height of left stack> and <Height of right stack> mm for the left and right stacks in cassette <Cassette>, the maximum allowed is <Maximum Height> mm. Remove some media from the cassette   Media Handler
40501   MDH: Load table center cups timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40502   MDH: Load table center cups vacuum timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40503   MDH: Load table left cups vacuum timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40504   MDH: Load table right cups vacuum timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40505   MDH: Pull out the loadtable and hold the load button to eject the plate   Media Handler
40506   MDH: Hold the load button to eject the plate   Media Handler
40507   MDH: Remove the ejected media and press MEDIA REMOVED. If you cannot reach the media on the load table, press RESUME.   Media Handler
40508   MDH: Cannot move the load table, it has not been initialized   Media Handler
40509   MDH: The load table is in, please pull out the load table   Media Handler
40510   MDH: The load table is not in, please push in the load table   Media Handler
40511   MDH: Unlock panels from PC and open hood.\nRemove any media on the load table.\nLock Panels.   Media Handler
40512   MDH: Media lost on load table.\nUnlock panels from PC and open hood.\nRemove any media on the load table.\nLock Panels.   Media Handler
40513   MDH: Load table plate stop timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40514   MDH: Load table failed to register plate   Media Handler
40515   MDH: Dual plates loaded where only one was expected   Media Handler
40516   MDH: Load table unable to measure stack shift. Plates in cassette <Cassette Number> larger than expected.\nVerify correct size, orientation, and stack location.   Media Handler
40517   MDH: Load table unable to measure stack shift. Plates in cassette <Cassette Number> smaller than expected.\nVerify correct size, orientation, and stack location.   Media Handler
40518   MDH: Load table did not arrive at the desired position   Media Handler
40519   MDH: Media on load table where none was expected, likely due to a previous fault.   Media Handler
40520   MDH: Plate(s) on load table did not arrive at registration pins <Home pin number> and <Away pin number>   Media Handler
40521   MDH: Media on load table where none was expected, likely due to a previous fault.   Media Handler
40522   MDH: Loadtable mainscan stage on timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40523   MDH: Loadtable mainscan stage off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40524   MDH: Unlock doors and remove media from the loadtable   Media Handler
40525   MDH: Loadtable failed to stage media on the mainscan stage pins, check <Media location>   Media Handler
40526   MDH: Loadtable unexpectedly detected media in the center of the loadtable while staging media   Media Handler
40527   MDH: Loadtable failed to have media properly register on the drum, check <Media location>   Media Handler
40601   MDH: Timeout, TEB did not trigger sensors   Media Handler
40607   MDH: Clamps expected to be on the trailing edge backbone, but they were not detected   Media Handler
40608   MDH: Clamps detected on the trailing edge backbone, but they were not expected   Media Handler
40613   MDH: Timeout, drum vacuum off   Media Handler
40616   MDH: Roller timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40622   MDH: LEC down preventing roller move down   Media Handler
40623   MDH: Registration continuity check failed, check media in leading edge clamp   Media Handler
40624   MDH: Media being loaded has been measured to have an unexpected main scan length   Media Handler
40625   MDH: Media being loaded has an invalid mainscan length, min=<Minimum mainscan length in mm> mm, max=<Maximum mainscan length in mm> mm   Media Handler
40626   MDH: Media being loaded has an invalid subscan length, min=<Minimum mainscan length in mm> mm, max=<Maximum mainscan length in mm> mm   Media Handler
40627   MDH: Media being loaded has an invalid thickness   Media Handler
40628   MDH: Media expected on the loadtable, but none was found   Media Handler
40629   MDH: Media partially loaded on drum, use RELEASE then remove the media   Media Handler
40630   MDH: Media fully on drum   Media Handler
40632   MDH: Media flyoff detected, please open panel and remove media   Media Handler
40634   MDH: Media is expected on the drum, but no media was found   Media Handler
40635   MDH: Cannot execute command because the drum is moving   Media Handler
40636   MDH: Drum not at the expected position, position may have shifted because of outside interaction   Media Handler
40637   MDH: Drum diameter improperly specified, check parameters   Media Handler
40638   MDH: Drum not initialized, use 'drum init' to initialize   Media Handler
40639   MDH: Could not find balancer arms, make sure that the tabs are blocking the sensors   Media Handler
40640   MDH: Fix angle for the balance too small for balancer arms, balancer arms cannot support specified media dimensions   Media Handler
40641   MDH: Could not find the balancer arm on the home side   Media Handler
40642   MDH: Could not find the balancer arm on the away side   Media Handler
40646   MDH: Loadtable sensor not detected   Media Handler
40651   MDH: Cannot calibrate (roller must be down)   Media Handler
40652   MDH: Cannot calibrate (media size measurement sensor bypassed)   Media Handler
40654   MDH: Cannot balance drum (balancer sensor bypassed)   Media Handler
40655   MDH: Drum vacuum level below 'vacuum on' threshold, check vacuum pump or recalibrate   Media Handler
40656   MDH: Home side balancer sensor is not detecting the tab after balancing move, check to make sure the actuator is working   Media Handler
40657   MDH: Home side balancer sensor is not detecting the tab after balancing move, check to make sure the actuator is working   Media Handler
40658   MDH: Media has invalid main scan length, it is smaller than expected   Media Handler
40659   MDH: Media has invalid main scan length, it is larger than expected   Media Handler
40660   MDH: Command could not be completed since the start button was bypassed   Media Handler
40663   MDH: Leading edge clamp timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40664   MDH: Trailing edge backbone timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40665   MDH: Trailing edge clamp lock/unlock timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40666   MDH: Exit door timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40667   MDH: Load ramp timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40668   MDH: Please remove media detected on load ramp   Media Handler
40669   MDH: Media not detected on load ramp   Media Handler
40670   MDH: Please move clamps to park position, then select RESUME   Media Handler
40672   MDH: Balancer <Presence type> presence not detected. [<I/O name>]   Media Handler
40673   MDH: Balancer timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40674   MDH: Leading edge clamp <Presence type> presence not detected. [<I/O name>]   Media Handler
40675   MDH: The roller was found on the drum, but was not expected   Media Handler
40676   MDH: Roller <Presence type> presence not detected. [<I/O name>]   Media Handler
40677   MDH: The leading edge clamp was expected closed, but was found to be open   Media Handler
40678   MDH: Trailing edge clamp <Presence type> presence not detected. [<I/O name>]   Media Handler
40679   MDH: Software error. Invalid registration pin combination   Media Handler
40680   MDH: Backbone <Presence type> presence not detected. [<I/O name>]   Media Handler
40681   MDH: Backbone timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40682   MDH: Backbone position cannot be determined   Media Handler
40683   MDH: Backbone cannot be found at center position   Media Handler
40684   MDH: Roller is down, cannot move LEC   Media Handler
40685   MDH: The trailing edge clamps are not at the expected drum position   Media Handler
40686   MDH: Cannot actuate the leading edge clamp at the current drum position   Media Handler
40687   MDH: Cannot actuate the trailing edge clamps at the current drum position   Media Handler
40688   MDH: Plate door timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40689   MDH: The plate door was found to be open when it should be closed   Media Handler
40690   MDH: Timeout waiting for load button, releasing media   Media Handler
40691   MDH: The drop table is open, please close drop table to continue   Media Handler
40692   MDH: Engine is currently busy, cannot change drum state   Media Handler
40693   MDH: Please remove media detected on load table   Media Handler
40694   MDH: Cannot execute command because media is on the drum   Media Handler
40695   MDH: <StacksSpecified> stacks specified, however this device has a maximum of <MaxStacks>   Media Handler
40696   MDH: The measurement sensor can only be calibrated using 1 stack of media, however more than 1 stack was being loaded   Media Handler
40697   MDH: No media found on the home side of the load ramp, media was expected   Media Handler
40698   MDH: No media found on the away side of the load ramp, media was expected   Media Handler
40699   MDH: Clamps on the trailing edge backbone are not consistent, one or more are missing   Media Handler
40701   MDH: Media being loaded was not measured as expected. It may be too long   Media Handler
40702   MDH: Media being loaded was not measured, most likely too long to be loaded on the drum (both sides)   Media Handler
40703   MDH: Media being loaded was not measured, most likely too long to be loaded on the drum (home side)   Media Handler
40704   MDH: Media being loaded was not measured, most likely too long to be loaded on the drum (away side)   Media Handler
40705   MDH: The two media stacks have difference in length of <LengthDifference> mm, tolerance is <Tolerance> mm, unable to load   Media Handler
40706   MDH: Media expected to be <ExpectedLength> mm, measured to be <MeasuredLength> mm on the <Side> side   Media Handler
40707   MDH: Media was loaded on the drum was too small, cannot recover   Media Handler
40708   MDH: Media main scan too big to be loaded on this drum - maximum is <Maximum mainscan media size in mm> mm   Media Handler
40709   MDH: Loader interface failed, invalid state <State>   Media Handler
40710   MDH: Loader not ready   Media Handler
40711   MDH: A loader error has occurred   Media Handler
40712   MDH: Cannot execute command because LEC is not down   Media Handler
40713   MDH: Cannot execute command because TEC is not down and locked to clamps   Media Handler
40714   MDH: Could not calculate the inertia of the drum   Media Handler
40715   MDH: Could not unlock clamps because the TEC is not on the drum   Media Handler
40716   MDH: Could not unlock clamps because the drum is not initialized (position is unknown)   Media Handler
40717   MDH: The TEC is not in a valid state, not all sensors are reading the same value   Media Handler
40718   MDH: Cannot calibrate the positions since the backbone is not at load position   Media Handler
40719   MDH: Registration failed   Media Handler
40720   MDH: Sensor accuracy <Sensor accuracy> mm, TEC offset <TEC offset> mm, possible to load media that will not be clamped   Media Handler
40721   MDH: Cannot balance the drum because the backbone is not at load position   Media Handler
40722   MDH: Stack locations (<Bit-field of the locations>) are not valid media positions   Media Handler
40723   MDH: Invalid stack count and/or media subscan size combination   Media Handler
40724   MDH: Unlock panels from PC.\nFlyoff sensor triggered. Open rear hood and remove media/obstruction from engine.\nLock Panels.   Media Handler
40725   MDH: Invalid stack count and rotate flag combination   Media Handler
40726   MDH: The engine is not clear for the unload table   Media Handler
40727   MDH: Registration failed   Media Handler
40728   MDH: Media is too <Limit type> to rotate, limit is <Limit amount> mm   Media Handler
40729   MDH: Drum vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]   Media Handler
40730   MDH: Cannot move the engine, it has not been initialized   Media Handler
40731   MDH: Registration failed. Unexpected contact with pin <Pin>   Media Handler
40732   MDH: Unable to move the head (Z) stage, it is locked   Media Handler
40733   MDH: Registration init failed. Registration sensor stuck on [<I/O name>].   Media Handler
40734   MDH: Plate funnel timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40735   MDH: Registration continuity check failed   Media Handler
40736   MDH: Registration monitor hardware failure (always on)   Media Handler
40737   MDH: Registration monitor hardware failure (always off)   Media Handler
40738   MDH: The specified media is not configured for media handling   Media Handler
40739   MDH: Invalid stack count and media mainscan size combination   Media Handler
40740   MDH: TEC adjust <Current TEC adjust> is too small for this plate size, should be at least <Recommended TEC adjust>   Media Handler
40741   MDH: Trailing edge clamp position invalid - load calibration required   Media Handler
40742   MDH: Media has invalid main scan length <MeasuredLength> mm, it is smaller than expected <ExpectedLength> mm   Media Handler
40743   MDH: Media has invalid main scan length <MeasuredLength> mm, it is larger than expected <ExpectedLength> mm   Media Handler
40744   MDH: Media has invalid main scan length, it is larger than expected <ExpectedLength> mm   Media Handler
40745   MDH: Media with a subscan size of <SubscanSize> cannot be loaded at location '<Location>'   Media Handler
40746   MDH: Pcup-funnel bar timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40747   MDH: Ramp to load position timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40748   MDH: Ramp to unload position timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40749   MDH: Unlock doors and remove media from the engine/drum   Media Handler
40750   MDH: Media subscan size of <Subscan size specified> mm is smaller than the minimum allowed of <Subscan size minimum> mm   Media Handler
40751   MDH: Media mainscan size of <Mainscan size specified> mm is smaller than the minimum allowed of <Mainscan size minimum> mm   Media Handler
40752   MDH: Media subscan size of <Subscan size specified> mm is larger than the maximum allowed of <Subscan size maximum> mm   Media Handler
40753   MDH: Media subscan size of <Subscan size specified> mm is larger than the maximum allowed for dual broadsheets of <Subscan size maximum> mm   Media Handler
40754   MDH: Media subscan size of <Subscan size specified> mm is larger than the maximum allowed for this location (<Subscan size maximum>) of <Location> mm   Media Handler
40755   MDH: Media mainscan size of <Mainscan size specified> mm is larger than the maximum allowed of <Mainscan size maximum> mm   Media Handler
40801   MDH: Unload table up/down timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40802   MDH: Unload table cups up/down timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40803   MDH: Unload table vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]   Media Handler
40804   MDH: Cannot move the unload table, it has not been initialized   Media Handler
40805   MDH: Timeout waiting for plate to leave unload table   Media Handler
40806   MDH: Unload cups rotated, cannot move unload table cups   Media Handler
40807   MDH: Unload stepper motor not in safe position to rotate cups   Media Handler
40808   MDH: Unload table rotate position sensor is already high (sensor may be broken)   Media Handler
40809   MDH: Please remove plate detected on unload table [<I/O name>]   Media Handler
40810   MDH: Rotator timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40811   MDH: Unable to pull media out of engine. Media still detected at entry sensor [<I/O name>]   Media Handler
40812   MDH: Media not detected at unload table entry [<I/O name>]   Media Handler
40813   MDH: Invalid exit number (exit #<Exit number>) selected   Media Handler
40814   MDH: The processor is not ready to accept plates   Media Handler
40815   MDH: The processor is in a faulted state   Media Handler
40816   MDH: The processor is still busy with the previous plate, so is unable to accept another   Media Handler
40817   MDH: Unload table tilt/untilt timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40818   MDH: Unload table center cups rotate/unrotate timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40819   MDH: Unload table cups vac on/off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40820   MDH: The unloadtable is tilted   Media Handler
40821   MDH: Cannot actuate the rotate mechanism at the current position   Media Handler
40822   MDH: The rotate option is not available on this device   Media Handler
40823   MDH: The unloadtable plate deflector is not detected   Media Handler
40824   MDH: Unlock panels from PC and open hood.\nRemove any media on the unload table.\nLock Panels.   Media Handler
40825   MDH: Workstation cannot connect to the PMI.\nPress RESUME when the processor is ready to accept the next plate   Media Handler
40826   MDH: Unable to [un]tilt the unloadtable, the bridge cover is open.   Media Handler
40827   MDH: Unload table did not arrive at the desired position   Media Handler
40828   MDH: The unloadtable plate deflector is obstructing the backbone   Media Handler
40829   MDH: Unloadtable pinch rollers open timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40830   MDH: Unloadtable pinch rollers close timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40831   MDH: Unloadtable table tilt to eject timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40832   MDH: Unloadtable table tilt to drum timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40833   MDH: Unloadtable rotator on timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40834   MDH: Unloadtable rotator off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40835   MDH: Unloadtable rotator rotate timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40836   MDH: Unloadtable rotator unrotate timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40837   MDH: Unloadtable rotator vacuum on timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40838   MDH: Unloadtable rotator vacuum off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40839   MDH: Unloadtable rotator is in an unknown state - manually check for interferences   Media Handler
40840   MDH: Cannot calibrate the unloadtable sensors since they are bypassed   Media Handler
40841   MDH: Unlock doors and remove media from the unloadtable   Media Handler
40842   MDH: Unloadtable failed to move media to the ejector, check <Media location>   Media Handler
40843   MDH: Unloadtable failed to move media to the pre-ejector position, check <Media location>   Media Handler
40844   MDH: Unloadtable failed to unload media from the drum, check <Media location>   Media Handler
40845   MDH: Unloadtable failed to re-stage media after unloading from the drum, check <Media location>   Media Handler
40870   MDH: Punch deflector up/down timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40871   MDH: Punch registration bar timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
40872   MDH: Punch cups vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]   Media Handler
40873   MDH: Punch failed to front register plate   Media Handler
40874   MDH: Punch failed to side register plate   Media Handler
40875   MDH: Punch did not arrive at the desired position   Media Handler
40876   MDH: The punch option is not available on this device   Media Handler
40877   MDH: The punch mechanism is not properly in its down position   Media Handler
40878   MDH: The punch mechanism is not properly in its forward position   Media Handler
40879   MDH: The punch debris ariflow is low. Possible blockage or leak.   Media Handler
40880   MDH: The punch debris removal timed out.   Media Handler
40901   MDH: Vacuum roller at up timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40902   MDH: Vacuum roller at up timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40903   MDH: Vacuum roller at neutral timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40904   MDH: Vacuum roller at neutral timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40905   MDH: Vacuum roller at down timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40906   MDH: Vacuum roller at down timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40907   MDH: Vacuum roller 4Up timeout: Failed to achieve vacuum threshold (<Threshold> kPa) within <Timeout> sec (only reached <ActualValue> kPa). [<I/O name>]   Media Handler
40908   MDH: Vacuum roller 8Up timeout: Failed to achieve vacuum threshold (<Threshold> kPa) within <Timeout> sec (only reached <ActualValue> kPa). [<I/O name>]   Media Handler
40909   MDH: Vacuum roller at up timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40910   MDH: Vacuum roller at up timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40911   MDH: Vacuum roller at neutral timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40912   MDH: Vacuum roller at neutral timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40913   MDH: Vacuum roller at down timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40914   MDH: Vacuum roller at down timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40915   MDH: Clean roller at neutral timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40916   MDH: Clean roller at neutral timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40917   MDH: Clean roller at vacuum roller timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40918   MDH: Clean roller at vacuum roller timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40919   MDH: Clean roller at drum timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40920   MDH: Clean roller at drum timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40921   MDH: Clean roller at neutral timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40922   MDH: Clean roller at neutral timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40923   MDH: Clean roller at vacuum roller timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40924   MDH: Clean roller at vacuum roller timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40925   MDH: Clean roller at drum timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40926   MDH: Clean roller at drum timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40927   MDH: Tape roller at down timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40928   MDH: Tape roller at down timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40929   MDH: Tape roller at down timeout: Failed to <Action> away sensor. [<I/O name>]   Media Handler
40930   MDH: Tape roller at down timeout: Failed to <Action> home sensor. [<I/O name>]   Media Handler
40931   MDH: Error, Vacuum Roller index sensor blocked after coarse homing   Media Handler
40932   MDH: Error, Vacuum Roller index sensor blocked before fine homing   Media Handler
40933   MDH: Error, Vacuum Roller index sensor blocked after fine homing   Media Handler
40934   MDH: Error, Vacuum Roller index sensor not blocked before coarse homing   Media Handler
40935   MDH: Drum vacuum timeout: Failed to exceed vacuum threshold (<Threshold> kPa) within <Timeout> sec (only reached <ActualValue> kPa). [<I/O name>]   Media Handler
40936   MDH: Drum vacuum timeout: Failed to fall below vacuum threshold (<Threshold> kPa) within <Timeout> sec (only reached <ActualValue> kPa). [<I/O name>]   Media Handler
40937   MDH: Invalid proof types   Media Handler
40938   MDH: Carrier not loaded or specified Proof Index is out of range   Media Handler
40939   MDH: Proofing media cassette not detected   Media Handler
40940   MDH: Wrong type of proofing media cassette detected.   Media Handler
40941   MDH: Drum vacuum sensor calibration required.   Media Handler
40942   MDH: Vacuum Roller 4Up vacuum sensor calibration required.   Media Handler
40943   MDH: Vacuum Roller 8Up vacuum sensor calibration required.   Media Handler
40944   MDH: Carrier verification not completed.   Media Handler
40945   MDH: Carrier verification failed.   Media Handler
40946   MDH: Proofing media flyoff detected, open panel and remove donor and receiver, use RESUME to continue   Media Handler
40947   MDH: Mis-loaded carrier detected (drum vacuum).   Media Handler
40948   MDH: Reseat <Proof Media Name> properly in cassette before RESUME   Media Handler
40949   MDH: Could not maintain drum vacuum using vacuum generator   Media Handler
40950   MDH: Cannot complete command because start button is stuck   Media Handler
40951   MDH: Fail to calibrate the vacuum offsets   Media Handler
40952   MDH: Invalid dimensions specified for <Proof type> carrier   Media Handler
40953   MDH: Invalid dimensions specified for <Proof type> receiver   Media Handler
40954   MDH: Invalid dimensions specified for <Proof type> donor   Media Handler
41001   MDH: Use drum control buttons to load media   Media Handler
41002   MDH: Use drum control buttons to unload media   Media Handler
41003   MDH: Start unloading media using the drum control buttons, or close the table   Media Handler
41004   MDH: Release the drum vacuum button   Media Handler
41005   MDH: Press the drum vacuum button   Media Handler
41006   MDH: Tape down leading edge and use drum control buttons to move drum to trailing edge tape position   Media Handler
41007   MDH: Use drum control buttons to move drum to leading edge tape position   Media Handler
41008   MDH: Open the table   Media Handler
41009   MDH: Close the table   Media Handler
41010   MDH: Load media on table   Media Handler
41011   MDH: Could not lock the table because the table was not closed   Media Handler
41012   MDH: Verify media if fully on drum and close the load table   Media Handler
41013   MDH: Continue with measured media size (<MeasuredLength> mm)?   Media Handler
41014   MDH: Turn the drum brake override switch off   Media Handler
41015   MDH: Open front cover by pushing RELEASE button   Media Handler
41016   MDH: Close front cover   Media Handler
41017   MDH: Engage and lock the tailstock   Media Handler
41018   MDH: Unlock, disengage, and move tailstock to up position   Media Handler
41019   MDH: LOCK HEADSTOCK CAMS! Press the camlock button when done   Media Handler
41020   MDH: Move drumlift lever to engaged position (towards tailstock)   Media Handler
41021   MDH: Move drumlift lever to disengaged position (towards headstock)   Media Handler
41022   MDH: Move drumlift to up position   Media Handler
41023   MDH: Move drumlift to down position   Media Handler
41024   MDH: Media being loaded has an invalid thickness: Measured (<MeasuredThickness> um) - Expected (<ExpectedThickness> um)   Media Handler
41025   MDH: Continue with measured media thickness (<MeasuredThickness> um)?   Media Handler
41026   MDH: Apply side tape to drum using drum control buttons (if required)   Media Handler
41027   MDH: Load the shell onto the arbor then engage and lock tailstock   Media Handler
41028   MDH: Remove unexpected media on load table   Media Handler
41029   MDH: SECURE ARBOR CLAMP ON ARBOR! Press the arbor clamp button when done   Media Handler
41030   MDH: Press RESUME to reload media or EJECT to cancel current image   Media Handler
41031   MDH: Tape trailing edge of media and close the table   Media Handler
41032   MDH: Drum balancing in progress   Media Handler
41033   MDH: Focusing head on media   Media Handler
41034   MDH: Media may be unloaded at this position if required   Media Handler
41035   MDH: Complete side taping and press the drum vacuum button   Media Handler
41036   MDH: Plate unloaded onto table, use drum control buttons to continue to either reload the plate or fully unload   Media Handler
41037   MDH: Use drum control buttons to move drum to media unload position or media further onto the load table   Media Handler
41038   MDH: Drum control buttons unavailable   Media Handler
41039   MDH: Load the large repeat arbor then engage and lock tailstock   Media Handler
41040   MDH: Move drumlift down away from drum, adjust drum position or fully unlock cams, and bring drumlift back up   Media Handler
41041   MDH: Drumlift lever in unexpected position(<Direction>)   Media Handler
41042   MDH: Drumlift lever disabled, RESUME to re-enable   Media Handler
41043   MDH: Press mandrel air button to turn on air   Media Handler
41044   MDH: Remove arbor and move drumlift to up position   Media Handler
41045   MDH: Override drum brake, unlock cams, bring transport cart into position, and then unlock the tailstock   Media Handler
41046   MDH: Rotate mandrel to position to disengage arbor clamp, unlock the tailstock, and remove the shell   Media Handler
41047   MDH: Remove the shell from the arbor then engage and lock tailstock   Media Handler
41048   MDH: Load the sleeve to be imaged then engage and lock tailstock   Media Handler
41049   MDH: Unload the sleeve then engage and lock tailstock   Media Handler
41050   MDH: Move tailstock to fully disengaged position before moving drumlift up   Media Handler
41051   MDH: Override drum brake, unlock cams, and then move drumlift to up position   Media Handler
41052   MDH: Measured mandrel diameter different from expected: Measured (<MeasuredDiameter>) - Expected (<ExpectedDiameter>)   Media Handler
41053   MDH: One touch operation failed <OperationDescription>   Media Handler
41054   MDH: One touch operation aborted   Media Handler
41055   MDH: One touch load/unload cannot operate in device mode with front door closed   Media Handler
41056   MDH: One touch mode select switch must be in device mode   Media Handler
41057   MDH: Engage processor shaft onto arbor. Push sleeve onto shell and push lever forward to first detent   Media Handler
41058   MDH: Move lever forward to control sleeve load. When sleeve is loaded, push lever fully forward to complete load   Media Handler
41059   MDH: Engage processor shaft onto arbor and pull lever backward to first detent   Media Handler
41060   MDH: Move lever backward to control sleeve unload. Pull lever fully backward and hold to complete unload   Media Handler
41061   MDH: Disengage processor shaft from the arbor then engage and lock tailstock   Media Handler
41062   MDH: Production hub lever range <RangeIndex> settings incorrect. <Limit> <Relation> <Limit>   Media Handler
41063   MDH: Cannot focus at position <Position> mm, check seam data and offset   Media Handler
41064   MDH: Press flashing device button on pedestal to start   Media Handler
41065   MDH: Remove media from device manually and close the table   Media Handler
41066   MDH: Load the small repeat arbor then engage and lock tailstock   Media Handler
41067   MDH: Select arbor to be loaded for this job   Media Handler
41068   MDH: Measured plate thickness of <Thickness> um is out of range of supported thicknesses   Media Handler
41069   MDH: Select arbor currently in device   Media Handler
41070   MDH: Change the shell for this job?   Media Handler
41071   MDH: Cannot unload sleeve media when drum is loaded. RESUME to clear device state   Media Handler
41072   MDH: Override drum brake, load/tape media onto drum manually, re-enable drum brake, and close the table   Media Handler
41073   MDH: Override drum brake, remove manually loaded media from drum, and press drum vacuum button when done   Media Handler
41074   MDH: Hoist not in down position. Move hoist to down position to continue   Media Handler
41075   MDH: Tailstock is not locked. Lock tailstock to continue   Media Handler
41076   MDH: Camlock or arborlock not acknowledged. Lock camlocks or arborlock and press the acknowledge button to continue   Media Handler
41077   MDH: Drum not exchanged for sheet mode. Ensure drum is mounted to continue   Media Handler
41078   MDH: Drum not exchanged for sleeve mode. Ensure arbor is mounted to continue   Media Handler
41079   MDH: Perform an exchange if required. Load device with selected media. Refer to operator's manual for more information   Media Handler
41080   MDH: An exchange was not properly completed. Restore either the drum or arbor to continue.   Media Handler
41500   OWB: Internal Error - 1-Wire-Bus response buffer became full   1-Wire-Bus Driver
41501   OWB: OWB General Failure   1-Wire-Bus Driver
41502   OWB: The 1-Wire-Bus appears to be shorted.   1-Wire-Bus Driver
41503   OWB: An Alarm presence pulse was found on the 1-Wire-Bus.   1-Wire-Bus Driver
41504   OWB: No node presence pulse was found on the 1-Wire-Bus.   1-Wire-Bus Driver
41505   OWB: The 1-Wire-Bus adapter (DS1411) is not responding.   1-Wire-Bus Driver
41506   OWB: Bad CRC received from a Node ID on the 1-Wire-Bus.   1-Wire-Bus Driver
41507   OWB: Write Data failed to verify from a Node on the 1-Wire-Bus.   1-Wire-Bus Driver
41514   OWB: No more Nodes on the 1-Wire-Bus.   1-Wire-Bus Driver
41600   KEY: Dongle Not found. Imaging is disabled.   Feature Control
41601   KEY: Too many devices detected.   Feature Control
41602   KEY: Dongle not initialized   Feature Control
41603   KEY: Duplicate dongle detected   Feature Control
41604   KEY: Invalid dongle detected   Feature Control
41605   KEY: Invalid serial number detected   Feature Control
41606   KEY: Invalid feature requested   Feature Control
41607   KEY: Optional feature specified not found   Feature Control
41608   KEY: Optional feature table is full   Feature Control
41800   IBM: General Failure   iButton Manager
41801   IBM: Invalid iButton Scanner data point handle   iButton Manager
41802   IBM: Cannot write to an iButton handle that is a READ value   iButton Manager
41803   IBM: Could not find the requested iButton handle   iButton Manager
41804   IBM: iButton Manager (IBM) is not initialized   iButton Manager
41805   IBM: The requested iButton handle is not available   iButton Manager
42900   PST: POST: <Test Code> - <Test Description>   POST Task
42901   PST: No response received from <Satellite Board>   POST Task
42902   PST: Unknown satellite board (ID=<Satellite ID>) found   POST Task
42903   PST: Invalid mode parameter in RCON command Get Post Result   POST Task
42999   PST: Machine Electronics FAILED Power On Self-Tests   POST Task
43001   DEB: Debris removal software error: <Software error>   Debris Removal
43002   DEB: Particulate Only Collection (POC) debris removal is not enabled on this device   Debris Removal
43003   DEB: Particulate and Chemical Collection (PACC) debris removal is not enabled on this device   Debris Removal
43004   DEB: The air jet is enabled, but not turned on   Debris Removal
43005   DEB: The blower is not turned on   Debris Removal
43006   DEB: The flow rate is below the minimum required   Debris Removal
43007   DEB: The cabinet has lost power   Debris Removal
43008   DEB: The particulate filter is not present or upside down, the lid is not closed, or the data cable is disconnected   Debris Removal
43009   DEB: The particulate filter is almost full. Please ensure a replacement filter is on hand   Debris Removal
43010   DEB: The particulate filter is full. You must replace the particulate filter to continue imaging   Debris Removal
43011   DEB: The debris collection nozzle is blocked   Debris Removal
43012   DEB: The debris hose is disconnected   Debris Removal
43013   DEB: There is a problem with one or more of the pressure sensors in the debris removal cabinet   Debris Removal
43014   DEB: The debris hose is disconnected, the cabinet has lost power, or the cabinet lid is not latched properly   Debris Removal
43015   DEB: There may be a partial blockage of the collection nozzle, or a leak, but the flow rate is still above minimum   Debris Removal
43016   DEB: There is a partial blockage of the collection nozzle, or a leak, and the flow rate is below minimum   Debris Removal
43017   DEB: The media being imaged releases potentially harmful emissions. See the Operator Manual for more information   Debris Removal
43018   DEB: The debris removal chemical filter is not present   Debris Removal
43019   DEB: The chemical filter has almost expired. Please ensure a replacement filter is on hand   Debris Removal
43020   DEB: The chemical filter has expired. You must replace the chemical filter and reset the output device to continue imaging   Debris Removal
43021   DEB: The chemical filter usage sensor is corrupt or the chemical filter was changed and the output device was not reset   Debris Removal
43022   DEB: Unable to communicate with the chemical filter. See the Operator Manual for more information   Debris Removal
43023   DEB: The chemical filter usage calculated is negative   Debris Removal
43024   DEB: Unable to calibrate <Sensor Name> pressure sensor   Debris Removal
43025   DEB: Unable to communicate with the chemical filter during initialization. See the Operator Manual for more information   Debris Removal
43026   DEB: Timeout: the pressure sensor output failed to stabilize   Debris Removal
43027   DEB: No debris removal options are enabled on this device   Debris Removal
43028   DEB: There is a problem with the nozzle pressure sensor in the output device   Debris Removal
43029   DEB: Command failed: cannot run more than one PACC option at a time   Debris Removal
43030   DEB: Cannot start new debris option while another is in an error condition   Debris Removal
43031   DEB: The chemical filter installed is not suitable for the selected media   Debris Removal
43032   DEB: The particulate filter is almost full AND the chemical filter has almost expired   Debris Removal
43033   DEB: Cannot setup ibutton: <IButton Parameter>   Debris Removal
43034   DEB: Chemical filter iButton already has valid usage information, did not reprogram   Debris Removal
43035   DEB: Conversion failed.   Debris Removal
43100   BXI: Component not bound   Buffer eXchange Interface
43101   BXI: Component busy   Buffer eXchange Interface
43102   BXI: Component cannot be deleted   Buffer eXchange Interface
43103   BXI: Connection closed   Buffer eXchange Interface
43104   BXI: Invalid parameter   Buffer eXchange Interface
43105   BXI: Outstanding BXI buffer request waiting   Buffer eXchange Interface
43200   DLP: DLP Subsystem internal error   Diagnostic Logging Protocol
43201   DLP: DLP Command API called in invalid sequence   Diagnostic Logging Protocol
43301   CRG: software error   Carriage (CTP)
43302   CRG: Carriage initialization timed out <Initialization operation>   Carriage (CTP)
43303   CRG: Carriage is reserved, command ignored   Carriage (CTP)
43304   CRG: The current carriage command has been preempted   Carriage (CTP)
43305   CRG: Carriage Hardware Fault: <Description of the faulted hardware component>   Carriage (CTP)
43306   CRG: Requested carriage velocity too high, recommended max = <Recommended maximum carriage velocity> mm/sec   Carriage (CTP)
43307   CRG: Carriage Accel requires Ispeed, Mspeed or velocity in range +/- <Maximum carriage velocity using current acceleration value> mm/s   Carriage (CTP)
43308   CRG: Carriage travel limit (<Text string describing which limits signals are active as follows>) unexpectedly hit   Carriage (CTP)
43309   CRG: Carriage velocity exceeds register size   Carriage (CTP)
43310   CRG: Carriage has aborted plotting   Carriage (CTP)
43311   CRG: Carriage can not reach requested position   Carriage (CTP)
43312   CRG: Carriage Amplifier fault: <Text string describing specific amplifier fault>   Carriage (CTP)
43313   CRG: Carriage currently initializing   Carriage (CTP)
43314   CRG: Carriage not initialized   Carriage (CTP)
43500   DF1: internal memory allocation error - DF1 Driver   DF1 Comm Protocol
43501   DF1: failure to open to the URT Subsystem - DF1 Driver   DF1 Comm Protocol
43601   MOP: MOP Initialization failed   Monitor Parser
43602   MOP: Argument name not found or used token in place of argument   Monitor Parser
43603   MOP: MOP API() function can only be used with optional tokens   Monitor Parser
43604   MOP: Internal MOP firmware error   Monitor Parser
43605   MOP: Unregistered MOP commands or MOP commands registered twice   Monitor Parser
43606   MOP: An invalid MOP access level was selected   Monitor Parser
43701   ZAD: Could not read the Z-Drive parameters   Z-Axis Drive Subsystem
43702   ZAD: Command not expected at this time   Z-Axis Drive Subsystem
43703   ZAD: Internal firmware error   Z-Axis Drive Subsystem
43704   ZAD: Command was aborted   Z-Axis Drive Subsystem
43705   ZAD: Error sending SMC motor command   Z-Axis Drive Subsystem
43706   ZAD: Zdrive stopped by external command   Z-Axis Drive Subsystem
43707   ZAD: Zdrive not initialized, position is unknown   Z-Axis Drive Subsystem
43708   ZAD: Zdrive motor could not be initialized, zdrive cannot be used   Z-Axis Drive Subsystem
43709   ZAD: Zdrive is busy   Z-Axis Drive Subsystem
43710   ZAD: Zdrive is busy trying to abort   Z-Axis Drive Subsystem
43711   ZAD: Zdrive is busy trying to stop   Z-Axis Drive Subsystem
43712   ZAD: Zdrive is in invalid state   Z-Axis Drive Subsystem
43713   ZAD: Zdrive received an invalid message   Z-Axis Drive Subsystem
43714   ZAD: Zdrive invalid internal structure   Z-Axis Drive Subsystem
43715   ZAD: Zdrive received an invalid state message   Z-Axis Drive Subsystem
43716   ZAD: Zdrive received an invalid message type   Z-Axis Drive Subsystem
43717   ZAD: Zdrive received an invalid message code   Z-Axis Drive Subsystem
43718   ZAD: Zdrive requires SMC version <SMC Version major>.<SMC Version minor>   Z-Axis Drive Subsystem
43802   ZAC: Another z axis sequence is currently being processed   Z Axis Control
43803   ZAC: Internal: Invalid parameter passed to function   Z Axis Control
43804   ZAC: Internal: System resource unavailable   Z Axis Control
43805   ZAC: Focus Error value requested while focus out of range or saturated   Z Axis Control
43806   ZAC: Z Axis Focus routine aborted by monitor command   Z Axis Control
43807   ZAC: Media not found by Z axis, confirm dimensions   Z Axis Control
43808   ZAC: Media not found by Z axis, confirm dimensions   Z Axis Control
43809   ZAC: Head operation timed out   Z Axis Control
43810   ZAC: Media not found by Z axis due to head collision, confirm dimensions   Z Axis Control
43811   ZAC: Eccentric media surface: Probable cause out-of-round cylinder / bad mount   Z Axis Control
43900   CTP: CTP Engine Component is not present - internal firmware error   CTP Engine Components
43901   CTP: CTP Processor Connected to Device   CTP Engine Components
43902   CTP: CTP Processor Not Enabled   CTP Engine Components
43903   CTP: Load or unload method not supported   CTP Engine Components
43904   CTP: Lost communication with the slave board   CTP Engine Components
43905   CTP: Master/slave operation timed out   CTP Engine Components
43906   CTP: Stack location(s) <Stack location> is not valid on this device   CTP Engine Components
43907   CTP: Stack location(s) <Stack location> does not match the number of stacks <Number of stacks>   CTP Engine Components
43908   CTP: Parameters used are invalid for this device   CTP Engine Components
44001   PSI: Could not read the Psi parameters   PLC Serial Interface
44002   PSI: Command not expected at this time   PLC Serial Interface
44003   PSI: Internal firmware error   PLC Serial Interface
44004   PSI: Command was aborted by a higher priority command   PLC Serial Interface
44005   PSI: Application layer timeout   PLC Serial Interface
44006   PSI: Datalink layer timeout   PLC Serial Interface
44101   DVC: Drum vacuum fatal error occurred   Drum Vacuum Control
44102   DVC: Invalid command sent to drum vacuum subsystem   Drum Vacuum Control
44103   DVC: Drum vacuum is in an invalid state   Drum Vacuum Control
44104   DVC: Drum vacuum is not initialized   Drum Vacuum Control
44105   DVC: Drum vacuum has encountered an error and must be turned off before it can be turned on again   Drum Vacuum Control
44106   DVC: Drum vacuum already running, must be turned off before it can be turned on again   Drum Vacuum Control
44107   DVC: Drum vacuum sensor gain not set   Drum Vacuum Control
44108   DVC: Drum vacuum received an invalid message   Drum Vacuum Control
44109   DVC: Drum vacuum command has an invalid callback   Drum Vacuum Control
44110   DVC: Drum vacuum command hijacked, drum vacuum turned off   Drum Vacuum Control
44111   DVC: Drum vacuum pressure is <current pressure in milli inches of HG> milliInHg, setpoint is <setpoint in milli inches of HG> milliInHg   Drum Vacuum Control
44112   DVC: Drum vacuum is not on, cannot check status   Drum Vacuum Control
44113   DVC: Drum vacuum is not on, cannot update   Drum Vacuum Control
44114   DVC: Drum vacuum <setpoint in milli inches of HG> milliInHg setpoint is too high, limit is <limit in milli inches of HG> milliInHg   Drum Vacuum Control
44115   DVC: Drum vacuum <setpoint in milli inches of HG> milliInHg setpoint not reached, current pressure is <current pressure in milli inches of HG> milliInHg   Drum Vacuum Control
44116   DVC: Drum vacuum frequency <setpoint in milliHz> milliHz is too high, max is <maximum in milliHz> milliHz   Drum Vacuum Control
44117   DVC: Drum vacuum pressure not stabilizing   Drum Vacuum Control
44118   DVC: Drum vacuum has not been updated   Drum Vacuum Control
44201   DTL: Non-head type message sent to DTL Driver   Head Communication Driver
44202   DTL: DTL Driver unable to determine message type   Head Communication Driver
44203   DTL: DTL Driver: invalid logical channel number   Head Communication Driver
44204   DTL: DTL head communication sync lost   Head Communication Driver
44205   DTL: DTL communication port not open   Head Communication Driver
44206   DTL: Timeout attempting to close communication port   Head Communication Driver
44207   DTL: DTL Server received a packet bigger than allowed   Head Communication Driver
44208   DTL: DTL Server received a packet containing an illegal command   Head Communication Driver
44209   DTL: DTL server or client failed to establish a TCP/IP connection   Head Communication Driver
44210   DTL: TCP socket is shut down locally or remotely   Head Communication Driver
44211   DTL: Internal error of TCP protocol   Head Communication Driver
44212   DTL: TCP socket create failure   Head Communication Driver
44213   DTL: TCP socket connect failure   Head Communication Driver
44214   DTL: TCP protocol received an invalid packet   Head Communication Driver
44215   DTL: TCP protocol link is not ready   Head Communication Driver
44300   CEH: Error Code [<Error code>] <Error string>   Creo Exposure Head
44301   CEH: Warning Fault [<Error code>] <Error string>   Creo Exposure Head
44302   CEH: Fatal Fault [<Error code>] <Error string>   Creo Exposure Head
44303   CEH: The write laser request is in progress   Creo Exposure Head
44304   CEH: The stroke calibration is in progress   Creo Exposure Head
44305   CEH: The focus request is in progress   Creo Exposure Head
44306   CEH: The requested media is not supported by the exposure head   Creo Exposure Head
44307   CEH: An upgrade of the host firmware is recommended   Creo Exposure Head
44308   CEH: An upgrade of the exposure head firmware is recommended   Creo Exposure Head
44309   CEH: An upgrade of the host firmware is required   Creo Exposure Head
44310   CEH: An upgrade of the exposure head firmware is required   Creo Exposure Head
44311   CEH: The requested functionality is not supported by the exposure head   Creo Exposure Head
44401   BOS: BOS subsystem not initialized - cannot proceed.   Blinking Output Server
44402   BOS: The requested update rate for the BOS subsystem is less than 50 ms   Blinking Output Server
44403   BOS: Error creating BOS group: Output bit already used elsewhere   Blinking Output Server
44404   BOS: Error creating BOS group: Too many outputs in group, max is 15   Blinking Output Server
44405   BOS: BOS Handle specified is invalid, cannot process action   Blinking Output Server
44406   BOS: New state for BOS group is invalid, cannot update group state.   Blinking Output Server
44407   BOS: BOS has run out of empty groups and so cannot create a new one.   Blinking Output Server
44408   BOS: BOS timed out trying to find a handle for a new group.   Blinking Output Server
44500   EHI: The exposure head is offline   Exposure Head Interface
44501   EHI: The exposure head is being initialized   Exposure Head Interface
44502   EHI: The exposure head has failed   Exposure Head Interface
44503   EHI: The exposure head is in programming mode   Exposure Head Interface
44504   EHI: The exposure head has been disabled   Exposure Head Interface
44505   EHI: Head command transporter is not open   Exposure Head Interface
44506   EHI: Head command transporter failure   Exposure Head Interface
44507   EHI: The response / unsolicited packet is invalid   Exposure Head Interface
44508   EHI: The response / unsolicited packet length is invalid   Exposure Head Interface
44509   EHI: The response / unsolicited packet protocol is invalid   Exposure Head Interface
44510   EHI: The unsolicited packet is not supported   Exposure Head Interface
44511   EHI: The exposure head control mode is invalid   Exposure Head Interface
44512   EHI: The exposure head type is invalid   Exposure Head Interface
44513   EHI: The exposure head control mode transition is invalid   Exposure Head Interface
44514   EHI: The exposure head has unexpectedly reset   Exposure Head Interface
44515   EHI: The baud rate negotiation algorithm has failed   Exposure Head Interface
44516   EHI: The application protocol negotiation algorithm has failed   Exposure Head Interface
44517   EHI: The command packet is not supported   Exposure Head Interface
44518   EHI: The exposure head is not supported   Exposure Head Interface
44519   EHI: Baud rate negotiation is not supported by the exposure head   Exposure Head Interface
44520   EHI: Application protocol negotiation is not supported by the exposure head   Exposure Head Interface
44521   EHI: The error string cannot be determined; the exposure head type is unknown   Exposure Head Interface
44522   EHI: The error string could not be retrieved from the exposure head   Exposure Head Interface
44523   EHI: The functionality is not supported   Exposure Head Interface
44524   EHI: Monitor redirection is not supported   Exposure Head Interface
44525   EHI: A parameter is invalid   Exposure Head Interface
44526   EHI: EHI port closed before head commands complete   Exposure Head Interface
44527   EHI: Command response from exposure head took too long   Exposure Head Interface
44528   EHI: Response from head incorrectly sequenced   Exposure Head Interface
44529   EHI: Parameter load already in progress   Exposure Head Interface
44530   EHI: Specified parameter group unknown   Exposure Head Interface
44531   EHI: Changed parameter unknown in thermal head   Exposure Head Interface
44532   EHI: The monitor command requires the exposure head to be online   Exposure Head Interface
44533   EHI: The monitor command requires application protocol 0   Exposure Head Interface
44534   EHI: The monitor command requires a Thermal 1.0 or Thermal 1.7x exposure head   Exposure Head Interface
44535   EHI: The monitor command requires a Tfx or Thermal 2 exposure head   Exposure Head Interface
44536   EHI: The Thermal 1.0 or Thermal 1.7x exposure head was unable to learn focus   Exposure Head Interface
44537   EHI: Timeout waiting for the focus   Exposure Head Interface
44538   EHI: Timeout waiting for the write laser   Exposure Head Interface
44539   EHI: The firmware version of the exposure head is not supported   Exposure Head Interface
44540   EHI: Unexpected software failure   Exposure Head Interface
44541   EHI: Head Command Transaction Buffer Overflow   Exposure Head Interface
44542   EHI: Head Media Data Block format is unsupported   Exposure Head Interface
44543   EHI: Timeout during head redirection access attempt   Exposure Head Interface
44544   EHI: Parameter access buffer overrun attempted   Exposure Head Interface
44545   EHI: The redirected command to the head failed   Exposure Head Interface
44546   EHI: The Media Data Block is missing data   Exposure Head Interface
44547   EHI: The head has requested to be powered down   Exposure Head Interface
44600   MPI: Carrier not loaded or specified Proof Index is out of range   Media Parameter Interface
44601   MPI: Invalid proof type   Media Parameter Interface
44602   MPI: Invalid proof border types   Media Parameter Interface
44603   MPI: No more media supported   Media Parameter Interface
44604   MPI: Media Image Mode ID out of range: <MIMID>   Media Parameter Interface
44605   MPI: Media matching MIMID not found   Media Parameter Interface
44606   MPI: Corrupted internal value detected   Media Parameter Interface
44607   MPI: Internal firmware failure   Media Parameter Interface
44608   MPI: MPI subsystem not initialized.   Media Parameter Interface
44609   MPI: Exposure head not available.   Media Parameter Interface
44610   MPI: Media name is blank or invalid   Media Parameter Interface
44611   MPI: Head operation timed out   Media Parameter Interface
44612   MPI: Invalid or unrecognized Media Data Block   Media Parameter Interface
44613   MPI: Media index out of range: <Media index>   Media Parameter Interface
44614   MPI: Buffer overflow   Media Parameter Interface
44615   MPI: MIMID <MIMID> already in use by slot <Slot Number>   Media Parameter Interface
44800   EHI: no error   Exposure Head Interface
44801   EHI: temperature out of range   Exposure Head Interface
44802   EHI: value out of range   Exposure Head Interface
44803   EHI: missing laser on parameters   Exposure Head Interface
44804   EHI: attempted write blocked   Exposure Head Interface
44805   EHI: failure to write to memory   Exposure Head Interface
44806   EHI: unsupported message   Exposure Head Interface
44807   EHI: message length incorrect   Exposure Head Interface
44808   EHI: invalid control message   Exposure Head Interface
44809   EHI: operation was aborted   Exposure Head Interface
44832   EHI: no more room in mailbox   Exposure Head Interface
44833   EHI: ran out of buffers   Exposure Head Interface
44834   EHI: all retries failed on chnl 0   Exposure Head Interface
44835   EHI: all retries failed on chnl 1   Exposure Head Interface
44836   EHI: sync lost on chnl 0   Exposure Head Interface
44837   EHI: sync lost on chnl 1   Exposure Head Interface
44848   EHI: CONFIG register incorrect   Exposure Head Interface
44849   EHI: flash memory checksum error   Exposure Head Interface
44850   EHI: LCA won't init for reprogram   Exposure Head Interface
44851   EHI: LCA won't admit being loaded   Exposure Head Interface
44852   EHI: SRAM memory check failure   Exposure Head Interface
44896   EHI: software error   Exposure Head Interface
44897   EHI: LCA config unavailable   Exposure Head Interface
44898   EHI: LCA not found   Exposure Head Interface
44899   EHI: hardware timeout   Exposure Head Interface
44946   EHI: WLC PCB overheated, reset head   Exposure Head Interface
44947   EHI: Laser drive current limit   Exposure Head Interface
44948   EHI: Laser safety interlock is open   Exposure Head Interface
44949   EHI: DTD laser diode over temperature   Exposure Head Interface
44950   EHI: DTD laser diode over voltage   Exposure Head Interface
44951   EHI: DTD laser diode over current   Exposure Head Interface
44952   EHI: DTD +24V supply low   Exposure Head Interface
44953   EHI: DTD +24V supply high   Exposure Head Interface
44954   EHI: DTD +15V supply low   Exposure Head Interface
44955   EHI: DTD temperature sensor open circuit   Exposure Head Interface
44956   EHI: DTD software timeout   Exposure Head Interface
44957   EHI: DTD reset asserted   Exposure Head Interface
44958   EHI: DTD temperature below set point   Exposure Head Interface
44959   EHI: DTD temperature above set point   Exposure Head Interface
44960   EHI: shutter disabled   Exposure Head Interface
44961   EHI: reset detected   Exposure Head Interface
44962   EHI: laser disabled   Exposure Head Interface
44963   EHI: focus not initialized: Execute 'focus init'   Exposure Head Interface
44964   EHI: focus error detected at <Subscan location> mm <Relative location> while imaging, check plate for artifacts   Exposure Head Interface
44965   EHI: laser shutdown detected   Exposure Head Interface
44966   EHI: head case over temperature, <Case temperature> C   Exposure Head Interface
44967   EHI: head ambient over temperature, <Ambient temperature> C   Exposure Head Interface
44968   EHI: media <Media number> not found in HDM nvs subsystem   Exposure Head Interface
44969   EHI: crash detected, error code = 0x<Error code>   Exposure Head Interface
44970   EHI: Warning - head temperature high, <Case temperature> C   Exposure Head Interface
44971   EHI: SCORR out of range   Exposure Head Interface
44972   EHI: checksum error in <NVS subsystem> calibration block   Exposure Head Interface
44973   EHI: checksum error in <NVS subsystem> configuration block   Exposure Head Interface
44974   EHI: newline error, check drum encoder and LC-BP cable   Exposure Head Interface
44975   EHI: media thickness out of range   Exposure Head Interface
44976   EHI: EH-PHI cbl. (hotlink fault)   Exposure Head Interface
44977   EHI: LV 24V not in range (unipolar)   Exposure Head Interface
44978   EHI: LV 24V or High voltage fault   Exposure Head Interface
44979   EHI: LV Over temperature   Exposure Head Interface
44980   EHI: LV Too much stray light for beam balance   Exposure Head Interface
44981   EHI: LV Negative 12V fault (unipolar)   Exposure Head Interface
44982   EHI: LV Bias current fault (unipolar)   Exposure Head Interface
44983   EHI: Recalibration is on   Exposure Head Interface
44984   EHI: Recalibration fault   Exposure Head Interface
44985   EHI: checksum error in stroke correction download   Exposure Head Interface
44986   EHI: LV Not enough light for beam balance   Exposure Head Interface
44987   EHI: stroke clock frequency invalid, aborting download   Exposure Head Interface
44988   EHI: DTD status unstable   Exposure Head Interface
44989   EHI: Laser sampling disabled (wsample == 0)   Exposure Head Interface
44990   EHI: Beam position sampling disabled (bsample == 0)   Exposure Head Interface
44991   EHI: Focus sampling disabled (fsample == 0)   Exposure Head Interface
44992   EHI: Light level too low for Beam Pointing   Exposure Head Interface
44993   EHI: Timeout waiting for LASER OK   Exposure Head Interface
44994   EHI: Light valve high voltage fault   Exposure Head Interface
44995   EHI: LV Positive 12V fault (bipolar)   Exposure Head Interface
44996   EHI: Stroke Clock or Imaging signal fault, check LC-BP cable   Exposure Head Interface
44997   EHI: Focus sensor fails linearity test, check head position   Exposure Head Interface
44998   EHI: Laser safety loop has just been closed   Exposure Head Interface
44999   EHI: Laser safety loop has just opened   Exposure Head Interface
45000   EHI: Only the safety loop detected by the head has closed   Exposure Head Interface
45001   EHI: Only the safety loop detected by the laser has closed   Exposure Head Interface
45008   EHI: executive call tsk_create() failed   Exposure Head Interface
45009   EHI: all tasks suspended   Exposure Head Interface
45010   EHI: executive call mbx_create() failed   Exposure Head Interface
45011   EHI: executive call mbx_send() failed   Exposure Head Interface
45012   EHI: executive call buf_alloc() failed   Exposure Head Interface
45013   EHI: executive call tmr_create() failed   Exposure Head Interface
45014   EHI: Task received message that was not sent   Exposure Head Interface
45015   EHI: Task sending message owned by another task   Exposure Head Interface
45016   EHI: Task sending unreserved message   Exposure Head Interface
45017   EHI: message buffer request failed   Exposure Head Interface
45018   EHI: Reserved message in message pool   Exposure Head Interface
45019   EHI: Task releasing message owned by another task   Exposure Head Interface
45020   EHI: Task releasing unreserved message   Exposure Head Interface
45021   EHI: message buffer release failed   Exposure Head Interface
45022   EHI: Unexpected message in mailbox   Exposure Head Interface
45023   EHI: Command parameter error   Exposure Head Interface
45024   EHI: Laser beam positioning not stable yet   Exposure Head Interface
45025   EHI: LV serial communications TX timeout   Exposure Head Interface
45026   EHI: timeout waiting for A/D output   Exposure Head Interface
45027   EHI: LV LCA not initialized   Exposure Head Interface
45028   EHI: LV LCA not done   Exposure Head Interface
45029   EHI: LV serial communications RX timeout   Exposure Head Interface
45030   EHI: LV board not connected   Exposure Head Interface
45031   EHI: incorrect light level at start of edge detection - check if plate loaded is too large   Exposure Head Interface
45032   EHI: Unable to balance stroke to better than head bpmaxerr percent   Exposure Head Interface
45033   EHI: library call failed   Exposure Head Interface
45034   EHI: the thermal head requires an upgrade   Exposure Head Interface
45035   EHI: case temperature high alarm, <Case temperature> C   Exposure Head Interface
45036   EHI: case temperature high warning, <Case temperature> C   Exposure Head Interface
45037   EHI: case temperature low alarm, <Case temperature> C   Exposure Head Interface
45038   EHI: case temperature low warning, <Case temperature> C   Exposure Head Interface
45039   EHI: ambient temperature high alarm, <Ambient temperature> C   Exposure Head Interface
45040   EHI: ambient temperature high warning, <Ambient temperature> C   Exposure Head Interface
45041   EHI: case and ambient temperature normal   Exposure Head Interface
45042   EHI: shutdown of thermal head due to temperature or humidity alarm   Exposure Head Interface
45043   EHI: thermal head humidity alarm, <Humidity> percent   Exposure Head Interface
45044   EHI: unable to learn focus, change focus mode or shift plot   Exposure Head Interface
45045   EHI: unable to find exposure power, set to 0 W   Exposure Head Interface
45100   STA: Internal: bad parameter   Statistics Reporting
45101   STA: Statistic identifier <Statistic identifier> was not registered   Statistics Reporting
45102   STA: Statistic identifier <Statistic identifier> has already been registered   Statistics Reporting
45103   STA: System resource unavailable   Statistics Reporting
45104   STA: Invalid statistic type for attempted operation   Statistics Reporting
45105   STA: Statistic data type description index out of range   Statistics Reporting
45201   PRD: The door locks are not engaged, check the door locks   Product Support
45202   PRD: The center panels are open, check the center panels   Product Support
45203   PRD: The center table is not detected, check the center table   Product Support
45204   PRD: WARNING: The device is currently running in simulation mode - for testing purposes only!   Product Support
45205   PRD: Invalid limit tag specified   Product Support
45206   PRD: Option '<Option name>' could not be enabled because option '<Option name>' is already enabled, only one is allowed   Product Support
45207   PRD: Option '<Option name>' could not be enabled because it is not allowed in this configuration   Product Support
45208   PRD: Lower back panel not detected, check panel   Product Support
45209   PRD: Top back panel not detected, check panel   Product Support
45210   PRD: Loader has a door open, check loader   Product Support
45211   PRD: Loader is not present   Product Support
45212   PRD: Drumlift hoist in up position   Product Support
45213   PRD: Chiller flow is too low   Product Support
45214   PRD: Frame temperature sensor is disconnected   Product Support
45215   PRD: Ballscrew temperature sensor is disconnected   Product Support
45216   PRD: Carriage collision: <Type>   Product Support
45217   PRD: Front hood is open, check front hood   Product Support
45218   PRD: Slipsheet bin rear panel not detected, check panel   Product Support
45219   PRD: Slipsheet bin cover panel not detected, check panel   Product Support
45220   PRD: Slipsheet bin panel not detected, check panel   Product Support
45221   PRD: MCU emergency stop switch is on   Product Support
45222   PRD: MCU safety sense is not on, check doors and emergency off switch   Product Support
45223   PRD: Cassette door open, check cassette door   Product Support
45224   PRD: The MCU rear doors are open, check doors   Product Support
45225   PRD: The MCU side access door is open, check door   Product Support
45226   PRD: The MCU right roof panel is open, check panel   Product Support
45227   PRD: The MCU left roof panel is open, check panel   Product Support
45228   PRD: The home head cover panel is open, check panel   Product Support
45229   PRD: The away head cover or bridge panel is open, check panel   Product Support
45230   PRD: Door loop fuse triggered, let fuse cool for 10 minutes   Product Support
45231   PRD: Flyoff occurred   Product Support
45232   PRD: Safety override switch is on, cannot plot with override on   Product Support
45233   PRD: Cannot verify if the write laser is on   Product Support
45234   PRD: Warning: System Pressure Low   Product Support
45235   PRD: Safety loop is not enabled (<I/OName>)   Product Support
45236   PRD: Head Input Fault: <Input bit description> (<Input bit name>) In Unexpected State   Product Support
45237   PRD: The door locks are engaged, but the doors are not locked - check the doors   Product Support
45238   PRD: Temperature conversion failed   Product Support
45239   PRD: Rear hood is open, check rear hood   Product Support
45240   PRD: MCU bypass panel is open, check MCU bypass panel   Product Support
45241   PRD: The away head cover is open, check panel   Product Support
45242   PRD: Chiller flow is too low (<bit description>)   Product Support
45243   PRD: Head Power Module safety circuit failure   Product Support
45244   PRD: The safety override keyswitch is activated   Product Support
45245   PRD: Option '<Option name>' could not be enabled because option '<Option name>' needs to be enabled first.   Product Support
45246   PRD: Cannot lock table when table not closed   Product Support
45247   PRD: License is invalid, product family is '<License Product Family>', it is required to be '<Product Family>'   Product Support
45248   PRD: License is invalid, option '<Option>' needs to be <Require state>   Product Support
45249   PRD: The write laser power is not being detected   Product Support
45250   PRD: License is invalid, unrecognized speed designator '<License Speed Designator>'   Product Support
45251   PRD: Option '<Option>' has changed due to licensing, device must be reset   Product Support
45252   PRD: Pallet loader door zone '1 front' is open   Product Support
45253   PRD: Pallet loader door zone '2 front' is open   Product Support
45254   PRD: Pallet loader door zone '3 front' is open   Product Support
45255   PRD: Pallet loader door(s) are open or unlocked   Product Support
45256   PRD: Pallet loader door zone '1 rear' is open   Product Support
45257   PRD: Pallet loader door zone '2 rear' is open   Product Support
45258   PRD: Pallet loader door zone '3 rear' is open   Product Support
45259   PRD: Pallet loader door zone 'end' is open   Product Support
45260   PRD: APL emergency stop switch is on   Product Support
45261   PRD: APL safety sense is not on, check doors and emergency off switch   Product Support
45262   PRD: The APL doors are unlocked   Product Support
45263   PRD: Component not available to set offline or online   Product Support
45264   PRD: Component <component name> is offline   Product Support
45265   PRD: Media dropped while drum spinning   Product Support
45266   PRD: Failed to unlock APL doors   Product Support
45267   PRD: Failed to lock the exit shutter   Product Support
45268   PRD: Ramp is in near the drum, cannot spin the drum   Product Support
45269   PRD: License has changed the bay limit, device needs to be reset   Product Support
45270   PRD: Front cassette doors are open   Product Support
45271   PRD: Front bypass door (above cassette doors) is open or latch is not closed   Product Support
45272   PRD: Right 1 panel is open (away side, near front)   Product Support
45273   PRD: Right 4 panel is open (away side, near eject)   Product Support
45274   PRD: Left 1 panel is open (home side, near front)   Product Support
45275   PRD: Left 3 panel is open (home side, mid-device)   Product Support
45276   PRD: Left 4 panel is open (home side, near eject)   Product Support
45277   PRD: Bottom eject panel is open   Product Support
45278   PRD: Top eject panel is open   Product Support
45279   PRD: Doors are not locked (primary loop)   Product Support
45280   PRD: Safety loop is not closed, check to make sure all doors are closed and locked   Product Support
45281   PRD: Front doors are not locked (secondary loop)   Product Support
45282   PRD: Front safety loop is not closed, check to make sure all front doors are closed and locked   Product Support
45283   PRD: <Board name> (<Board ID>) <Relay name> relay contacts welded, replace board   Product Support
45301   SPC: Parameters settings prevent spray   Spray-On Option
45302   SPC: Command has been cancelled via API call   Spray-On Option
45303   SPC: Can't start pumps for current liquid - one or more flow rates are zero   Spray-On Option
45304   SPC: Invalid parameter or unallocated message detected   Spray-On Option
45400   _405: PPC 405 General Failure   IBM405PPC Processor
45401   _405: reset induced by software watchdog   IBM405PPC Processor
45700   GMCEX: Bad Memory Address specified in monitor command   GMCE Xilinx Board
45701   GMCEX: GMCE board memory erase failure has occured   GMCE Xilinx Board
45702   GMCEX: Failure reading eeprom or flash memory   GMCE Xilinx Board
45703   GMCEX: Failure writing to eeprom or flash memory   GMCE Xilinx Board
45704   GMCEX: An Un-Supported CPU Interrupt has occured.   GMCE Xilinx Board
45705   GMCEX: RCON File Burn Status Query With Invalid File ID   GMCE Xilinx Board
45706   GMCEX: Invalid format type   GMCE Xilinx Board
45707   GMCEX: Invalid engineering units   GMCE Xilinx Board
45708   GMCEX: Failure creating or configuring TCP/IP socket   GMCE Xilinx Board
45709   GMCEX: Invalid IP address received for TH3 head   GMCE Xilinx Board
45710   GMCEX: A calculated file checksum is invlaid   GMCE Xilinx Board
45801   MDH: Cannot move the fetcher, it has not been initialized   Media Handler
45802   MDH: The fetcher is in an unknown position (uninitialized)   Media Handler
45803   MDH: The fetcher is in an unsafe position for the cassette   Media Handler
45804   MDH: Fetcher plate vacuum on/off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
45805   MDH: Fetcher slipsheet wedgemaster up/down timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
45806   MDH: Fetcher slipsheet vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]   Media Handler
45807   MDH: Slipsheet remover roller on/off/open/close timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
45808   MDH: Slipsheet remover compactor on/off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
45809   MDH: Plenum SS mirror expected to be found in the plenum but was not   Media Handler
45810   MDH: Fetcher plenum slipsheet mirror in/out timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
45811   MDH: Plenum SS sensor expected to find a slipsheet in the cassette but did not. Check following plate for scratches   Media Handler
45812   MDH: Unable to move the fetcher stepper, the service access panel is open   Media Handler
45813   MDH: Unable to execute command, the slipsheet bin door is open   Media Handler
45814   MDH: The slipsheet bin is not present in the device   Media Handler
45815   MDH: The fetcher is not clear for the unload table   Media Handler
45816   MDH: Plate handoff from fetcher to load table failed.   Media Handler
45817   MDH: There is no plate detected on the fetcher where one was expected   Media Handler
45818   MDH: There is no plate detected on the fetcher by the fetcher vacuum, where one was expected   Media Handler
45819   MDH: There is an obstruction above the slipsheet rollers   Media Handler
45820   MDH: There is an obstruction above the slipsheet rollers likely due to a full slipsheet bin. Empty the slipsheet bin   Media Handler
45821   MDH: A slipsheet was detected beneath the plate on the loadtable.   Media Handler
45822   MDH: Unable to actuate the compactor, the slipsheet roller is open   Media Handler
45823   MDH: Open Panels.\nRemove any media from the fetcher and/or slipsheet area   Media Handler
45824   MDH: Open slipsheet bin cover.\nPlate lost from fetcher.\nRemove any media from the slipsheet area   Media Handler
45825   MDH: Plate lost from fetcher.\nUnlock panels from PC and open hood.\nRemove any media from the load table.\nLock Panels.   Media Handler
45826   MDH: There is no plate detected on the fetcher where one was expected.\n Plates in cassette <Cassette Number> may be pinched by the side rails.   Media Handler
45827   MDH: Open slipsheet bin cover.\nThere is an obstruction above the slipsheet rollers. Remove obstruction and check slipsheet bin level   Media Handler
45828   MDH: Open slipsheet bin cover.\nThere is an obstruction above the slipsheet rollers. Remove obstruction and check slipsheet bin level   Media Handler
45829   MDH: Unlock panels from PC and open hood.\nPlate stuck on fetcher.\nRemove any media from the fetcher.\nLock Panels.   Media Handler
45830   MDH: Plate handoff to fetcher failed.   Media Handler
45831   MDH: Plate handoff to fetcher failed. Verify position of end stops in cassette <Cassette Number>.   Media Handler
45832   MDH: Open slipsheet bin cover.\nPlate width window calibration failed. Check for plate or debris on fetcher deck   Media Handler
45833   MDH: Fetcher did not arrive at the desired position   Media Handler
45834   MDH: Timeout waiting for the fetcher to become free   Media Handler
45835   MDH: Open slipsheet bin cover.\nThere is an obstruction on the plenum. Remove obstruction   Media Handler
45836   MDH: The slipsheet bin is full. Empty slipsheet bin.   Media Handler
45901   MDH: A plate was expected to be at the processor but was not found or did not arrive   Media Handler
45902   MDH: No plate was expected to be at the processor but one was found. Check for processor malfunction   Media Handler
45903   MDH: The ejector is not clear for the unload table   Media Handler
45904   MDH: Open bridge cover panel.\nRemove any media on the processor bridge   Media Handler
45905   MDH: Cannot move the ejector, it has not been initialized   Media Handler
45906   MDH: Unable to eject plates: the gap between the plates is too small   Media Handler
45907   MDH: Ejector did not arrive at the desired position   Media Handler
45908   MDH: Ejector kicker on/off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
45909   MDH: Ejector pinch rollers open timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
45910   MDH: Ejector pinch rollers open timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
45911   MDH: Media on <Media location> did not clear the ejector after <Time waited> minutes, ensure media is clear from device exit   Media Handler
45912   MDH: Remove media from the ejector, unlock doors if necessary   Media Handler
45913   MDH: Timeout waiting for media to exit the bridge, possible processor fault   Media Handler
46001   SSI: Internal firmware error   Servo Serial Interface
46002   SSI: Parameter error. Expecting '<Expected parameter value range>'   Servo Serial Interface
46003   SSI: Command was aborted by a higher priority command   Servo Serial Interface
46004   SSI: The current servo command has been preempted   Servo Serial Interface
46005   SSI: Servo controller response timeout   Servo Serial Interface
46006   SSI: Servo controller response not recognized   Servo Serial Interface
46007   SSI: Servo controller command error: <Error message reported by servo controller>   Servo Serial Interface
46008   SSI: Servo controller '<Error message reported by servo controller>' error   Servo Serial Interface
46009   SSI: Command was aborted by the servo controller   Servo Serial Interface
46010   SSI: Error while initializing servo   Servo Serial Interface
46011   SSI: Servo controller 'home' command failed   Servo Serial Interface
46012   SSI: Servo travel limit (<Text string describing which limits signals are active as follows>) unexpectedly hit   Servo Serial Interface
46013   SSI: Servo timed out while searching for 'home'   Servo Serial Interface
46014   SSI: User attempted to register more than one callback function   Servo Serial Interface
46201   FWD: Empty firmware directory sector   Firmware Directory
46202   FWD: FWD Entry Not Found   Firmware Directory
46203   FWD: FWD handle is invalid   Firmware Directory
46204   FWD: FWD entry table integrity error   Firmware Directory
46205   FWD: Component ID is invalid   Firmware Directory
46206   FWD: Invalid function parameter   Firmware Directory
46207   FWD: Firmware directory entry table is full   Firmware Directory
46208   FWD: Invalid firmware directory entry or component check sum   Firmware Directory
46209   FWD: Directory table synchronization failure   Firmware Directory
46210   FWD: Directory table contains duplicated entries   Firmware Directory
46211   FWD: Directory table need to be validated   Firmware Directory
46212   FWD: End of directory table reached   Firmware Directory
46213   FWD: Firmware directory system is locked   Firmware Directory
46214   FWD: Failed to lock firmware directory system   Firmware Directory
46301   SCS: SCS General Failure   SCON Server
46302   SCS: socket() call has failed   SCON Server
46303   SCS: bind() call has failed   SCON Server
46304   SCS: listen() call has failed   SCON Server
46305   SCS: accept() call has failed   SCON Server
46306   SCS: recv() call has failed   SCON Server
46307   SCS: send() call has failed   SCON Server
46401   CNS: CNS General Failure   CAN Bus Packet Server
46402   CNS: socket() call has failed   CAN Bus Packet Server
46403   CNS: bind() call has failed   CAN Bus Packet Server
46404   CNS: recvfrom() call has failed   CAN Bus Packet Server
46405   CNS: sendto() call has failed   CAN Bus Packet Server
46406   CNS: tfRegisterSocketCB() call has failed   CAN Bus Packet Server
46407   CNS: Internal CNS subsystem resource table is full   CAN Bus Packet Server
46501   CFS: Invalid Path   Creo File System
46502   CFS: No More File/Dir Entry In Subdirectory   Creo File System
46503   CFS: API Function Not Supported   Creo File System
46504   CFS: File or Directory Already Exist   Creo File System
46505   CFS: File Or Directory Not Found   Creo File System
46506   CFS: Path Not Found   Creo File System
46507   CFS: Invalid File Attribute   Creo File System
46508   CFS: Invalid Handle   Creo File System
46509   CFS: Invalid Directory Tree   Creo File System
46510   CFS: File or Subdirectory Deletion Is Not Allowed   Creo File System
46511   CFS: No More Directory_Entry Is Available   Creo File System
46512   CFS: End Of File Reached   Creo File System
46513   CFS: File Write Is Not Allowed   Creo File System
46514   CFS: Media Is Full   Creo File System
46515   CFS: File Allocation Table Integrity Error   Creo File System
46516   CFS: Subdirectory Can Not Be Deleted   Creo File System
46517   CFS: Exclusive File Open Failure   Creo File System
46518   CFS: File/Dir Rename Failure   Creo File System
46519   CFS: Firmware Binary File Deletion Refused   Creo File System
46601   GDPC: socket() call failed: <Error description>   GMCE Data Path Control
46602   GDPC: bind() call failed: <Error description>   GMCE Data Path Control
46603   GDPC: recvfrom() call failed: <Error description>   GMCE Data Path Control
46604   GDPC: sendto() call failed: <Error description>   GMCE Data Path Control
46605   GDPC: tfGetArpEntryByIpAddr() call failed: <Error description>   GMCE Data Path Control
46606   GDPC: Hotlink FIFO is full, too much data to write!   GMCE Data Path Control
46607   GDPC: The stroke width is not a multiple of 8 or is too large   GMCE Data Path Control
46608   GDPC: The swath is too large to fit in the hotlink FIFO   GMCE Data Path Control
46609   GDPC: The test pattern specified is not defined   GMCE Data Path Control
46610   GDPC: Test pattern generation is already in progress   GMCE Data Path Control
46611   GDPC: Invalid packet received from PSRM   GMCE Data Path Control
46612   GDPC: Invalid protocol version in packet received from PSRM   GMCE Data Path Control
46613   GDPC: Client IP address changed during job   GMCE Data Path Control
46614   GDPC: Invalid sequence number in PSRM open request   GMCE Data Path Control
46615   GDPC: Xilinx TH2DP module version <Current major version>.<Current minor version> is invalid, must be at least <Minimum required major version>.<Minimum required minor version>   GMCE Data Path Control
46616   GDPC: A data overflow occured in the input FIFO, image is corrupt   GMCE Data Path Control
46617   GDPC: A data underrun occured in the input FIFO, image is corrupt   GMCE Data Path Control
46618   GDPC: A data overflow occured in the output FIFO, image is corrupt   GMCE Data Path Control
46619   GDPC: A data underrun occured in the output FIFO, image is corrupt   GMCE Data Path Control
46701   HIM: A parameter to an internal function is invalid   Head Interface Manager
46702   HIM: Attempt to register too many notification callbacks   Head Interface Manager
46703   HIM: Attempt to clear callback that was not previously established   Head Interface Manager
46704   HIM: Head command currently in progress has been preempted   Head Interface Manager
46705   HIM: The head programming operation could not be started   Head Interface Manager
46706   HIM: Head programming state machine integrity violated   Head Interface Manager
46707   HIM: File download state machine integrity violated   Head Interface Manager
46708   HIM: No response from the head while downloading bootloader   Head Interface Manager
46709   HIM: Protocol violation while downloading bootloader to the head   Head Interface Manager
46710   HIM: Head does not support this version of bootloader   Head Interface Manager
46711   HIM: No response from the head while programming   Head Interface Manager
46712   HIM: Protocol violation while programming the head   Head Interface Manager
46713   HIM: Head bootloader failed to program   Head Interface Manager
46714   HIM: Serial port overflow while programming the head   Head Interface Manager
46715   HIM: No data received from the workstation while programming the head   Head Interface Manager
46716   HIM: 'S' expected (received <Received character>) at start of record <Line number> in S-record file   Head Interface Manager
46717   HIM: Invalid record type found at record <Line number> in S-record file   Head Interface Manager
46718   HIM: Invalid data byte <Invalid byte> found at offset <Record offset> of record <Line number> in S-record file   Head Interface Manager
46719   HIM: Checksum failed on record <Line number> in S-record file   Head Interface Manager
46720   HIM: Extra character(s) found at end of record <Line number> in S-record file   Head Interface Manager
46721   HIM: Multiple head interface failures - check interface cable   Head Interface Manager
46722   HIM: No head detected on fiber link - check cable and BOOTP server   Head Interface Manager
46723   HIM: No head detected on serial link - check cable   Head Interface Manager
46724   HIM: Thermal head FTP download file has an invalid checksum   Head Interface Manager
46725   HIM: Thermal head FTP download file name is invalid   Head Interface Manager
46801   CFL: Not connected to the Feature Licensing Server   Creo Feature Licensing
46802   CFL: XML Parser Overflow   Creo Feature Licensing
46803   CFL: XML Unknown escape sequence   Creo Feature Licensing
46804   CFL: Illegal character in XML message   Creo Feature Licensing
46806   CFL: Invalid State in XML parser   Creo Feature Licensing
46807   CFL: Malformed XML message detected   Creo Feature Licensing
46808   CFL: XML Parser memory allocation failure   Creo Feature Licensing
46809   CFL: XML Parser does not support more than 8 bit characters   Creo Feature Licensing
46810   CFL: Feature Licensing detected encryption memory corruption   Creo Feature Licensing
46811   CFL: Feature Licensing detected a failure with a socket operation   Creo Feature Licensing
46812   CFL: Communication timeout with the Feature Licensing Server   Creo Feature Licensing
46813   CFL: XML Node Not found   Creo Feature Licensing
46814   CFL: Feature licensing authentication failure   Creo Feature Licensing
46815   CFL: Feature Licensing integrity check failed   Creo Feature Licensing
46816   CFL: Licensing feature is not supported   Creo Feature Licensing
46817   CFL: Feature value for "<Limit Name - This is the name of the feature value that is being verified>" (<Limit ID - The numeric representation (Limit Tag value>) is outside of it's licensed range   Creo Feature Licensing
46818   CFL: Feature Licensing subsystem is not initialized   Creo Feature Licensing
46819   CFL: Invalid limit tag <Tag - The parameter is the numeric value of the internally used limit tag> used.   Creo Feature Licensing
46820   CFL: No more Feature Licensing connections available   Creo Feature Licensing
46821   CFL: Invalid Feature Licensing connection ID   Creo Feature Licensing
46822   CFL: Feature Licensing connection has been disconnected   Creo Feature Licensing
46823   CFL: Feature Licensing connection failed   Creo Feature Licensing
46824   CFL: Feature Licensing Server had an internal error   Creo Feature Licensing
46825   CFL: Feature Licensing Server communication failed   Creo Feature Licensing
46826   CFL: Feature Licensing Server cannot detect a service dongle   Creo Feature Licensing
46827   CFL: Feature Licensing Server was requested information about a invalid service component   Creo Feature Licensing
46828   CFL: Feature Licensing Server cannot find the appropriate license   Creo Feature Licensing
46829   CFL: Feature Licensing Server cannot detect a customer dongle   Creo Feature Licensing
46830   CFL: Invalid IP address used when communicating with the Feature Licensing Server   Creo Feature Licensing
46831   CFL: Feature Licensing Server detects an invalid customer dongle   Creo Feature Licensing
46832   CFL: Feature Licensing Server does not support this version of firmware   Creo Feature Licensing
46833   CFL: Feature Licensing Server could not find requested feature   Creo Feature Licensing
46834   CFL: Feature Licensing Server could not find requested tag   Creo Feature Licensing
46835   CFL: Feature Licensing Server could not find requested value   Creo Feature Licensing
46901   DCC: Just a placeholder error   DC Motor Control
47001   PUN: Punch subsystem is not initialized   Punch
47002   PUN: Internal integrity failure   Punch
47003   PUN: Punch Motor <MotorID - The punch motor that is not initialized> is not initialized   Punch
47004   PUN: Punch Motor <MotorID - The punch motor that has failed> retry limit exceeded   Punch
47005   PUN: Initialization Required   Punch
47006   PUN: Punch system is busy   Punch
47008   PUN: Punch group is out of range   Punch
47009   PUN: Punch motor ID is out of range   Punch
47010   PUN: The punch system option is not enabled   Punch
47011   PUN: Punch motor is not present   Punch
47012   PUN: Punch system already initializing   Punch
47013   PUN: Punch Motor <MotorID - The punch motor that has drawn execssive current> has exceeded firmware current threshold   Punch
47014   PUN: Punch Motor <MotorID - The punch motor that has drawn execssive current> has exceeded hardware current threshold   Punch
47015   PUN: Punch Motor <MotorID - The punch motor that has timed out during the punch cycle> has timed out while attempting a full cycle   Punch
47101   CAM: No results buffers left in pool   Camera
47102   CAM: Event not allowed in the current subsystem state   Camera
47103   CAM: Event not allowed in the current subsystem state   Camera
47104   CAM: Camera strobe field was not expected   Camera
47105   CAM: Strobe collision   Camera
47106   CAM: Strobe split   Camera
47107   CAM: Drum failed to reach strobe position   Camera
47108   CAM: Timed out waiting for strobe field from camera   Camera
47109   CAM: Field capture is pending   Camera
47110   CAM: Field was not captured   Camera
47111   CAM: No space to save file to firmware FTP folder   Camera
47112   CAM: Video signal from edge detect camera not detected   Camera
47113   CAM: LED driver board(s) not detected   Camera
47114   CAM: Sending camera file to the workstation over TCP link failed   Camera
47201   CED: No results buffers left in pool   Camera Edge Detect
47202   CED: Event not allowed in the current subsystem state   Camera Edge Detect
47203   CED: Internal firmware error   Camera Edge Detect
47204   CED: Camera strobe field was not expected   Camera Edge Detect
47205   CED: Horizontal edge not found during calibration   Camera Edge Detect
47206   CED: Requested edge detect point is not on plate (mainscan) (check calibration)   Camera Edge Detect
47207   CED: Camera has not been calibrated for this media thickness   Camera Edge Detect
47208   CED: Vertical edge not found   Camera Edge Detect
47209   CED: Cannot calibrate camera when away edge detect is requested   Camera Edge Detect
47400   MDH: Picker was unable to measure stack heights in cassette <Cassette> because the height differential between each side was greater than <Maximum differential> mm   Media Handler
47401   MDH: Picker measured a height difference of <Height differential> mm between broadsheet stacks in cassette <Cassette>, the maximum allowed is <Maximum differential> mm   Media Handler
47402   MDH: Picker measured a height difference of <Height differential> mm between panorama sides in cassette <Cassette>, the maximum allowed is <Maximum differential> mm. Recalibrate picker   Media Handler
47403   MDH: Picker unexpectedly detected a media stack on <Stack Location> side in cassette <Cassette>, remove all the media from this side   Media Handler
47404   MDH: Picker feet on timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
47405   MDH: Picker feet off timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
47406   MDH: Picker reflex cycle list is at its maximum of <Maximum cycles> cycles, cannot add anymore   Media Handler
47407   MDH: Picker cannot pick slip sheets with rigid airjets installed, only non-slip sheet plates are supported   Media Handler
47500   DMC: The DC motor is not supported by the product   DC Motor Control
47501   DMC: The handle of the DC motor is invalid   DC Motor Control
47502   DMC: The requested movement of the DC motor is invalid   DC Motor Control
47503   DMC: The DC motors do not support synchronous movement   DC Motor Control
47504   DMC: The DC motor is being initialized   DC Motor Control
47505   DMC: The DC motor has been disabled   DC Motor Control
47506   DMC: The DC motor has been reserved   DC Motor Control
47507   DMC: The DC motor has timed out   DC Motor Control
47601   MDHAPL: <Motor name> axis motor did not arrive at the desired position   Media Handler (APL)
47602   MDHAPL: Actuator timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler (APL)
47603   MDHAPL: Picker <Side> tower not found   Media Handler (APL)
47604   MDHAPL: Cannot move the <Mechanism>, it has not been initialized   Media Handler (APL)
47605   MDHAPL: Cannot move <mechanism to move>, <unsafe mechanism> not in safe state   Media Handler (APL)
47606   MDHAPL: <Motor name> position not found   Media Handler (APL)
47607   MDHAPL: Pusher <Axis name> not found <Sensor name>   Media Handler (APL)
47608   MDHAPL: <Parameter name> parameter not initialized   Media Handler (APL)
47609   MDHAPL: Timeout waiting for the <Motor name> motor to become free   Media Handler (APL)
47610   MDHAPL: <I/O name> vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) (only reached <ActualValue>).   Media Handler (APL)
47611   MDHAPL: <Sensor name> sensor invalid state (<Sensor state>)   Media Handler (APL)
47612   MDHAPL: The plate is misaligned in bay <bay>   Media Handler (APL)
47613   MDHAPL: <Motor name> motor not initialized   Media Handler (APL)
47614   MDHAPL: Plate detected on pusher shoes. Top plate may be damaged ( bay <bay> )   Media Handler (APL)
47615   MDHAPL: Multiple plates detected on <Location> ( bay <bay> )   Media Handler (APL)
47616   MDHAPL: No plate detected on <Location> ( bay <bay> )   Media Handler (APL)
47617   MDHAPL: Unable to <request>, check the <mechanism>   Media Handler (APL)
47618   MDHAPL: Closing the APL requires at least one defined bay   Media Handler (APL)
47619   MDHAPL: Failure threading the picker towers through the plate stacks ( bay <bay> )   Media Handler (APL)
47620   MDHAPL: The plate stack cannot be used ( bay <bay> ), <reason>   Media Handler (APL)
47621   MDHAPL: The plate stack was not detected ( bay <bay> )   Media Handler (APL)
47622   MDHAPL: The plate stack is configured incorrectly ( bay <bay> )   Media Handler (APL)
47623   MDHAPL: The pallet hunting algorithm has failed ( bay <bay> )   Media Handler (APL)
47624   MDHAPL: The plate stack is positioned too far back ( bay <bay> )   Media Handler (APL)
47625   MDHAPL: The plate stack is positioned too close ( <side>-side of bay <bay> )   Media Handler (APL)
47626   MDHAPL: The plate stack does not match the mainscan size ( bay <bay> )   Media Handler (APL)
47627   MDHAPL: The plate stack does not match the subscan size ( bay <bay> )   Media Handler (APL)
47628   MDHAPL: The plate stack has exceeded the maximum skew ( bay <bay> )   Media Handler (APL)
47629   MDHAPL: The plate stack has exceeded the maximum tilt ( bay <bay> )   Media Handler (APL)
47630   MDHAPL: Plate handoff to pusher failed ( bay <bay> ).   Media Handler (APL)
47631   MDHAPL: Plate left inside APL. Unlock APL.\nRemove plate from the transfer table.\n Lock APL.   Media Handler (APL)
47632   MDHAPL: No Slipsheet detected in bay <bay>.\nTop plate may be damaged.   Media Handler (APL)
47633   MDHAPL: The picked plate is lost inside the APL   Media Handler (APL)
47634   MDHAPL: A slip sheet has been detected on top of the plate in bay <bay>   Media Handler (APL)
47635   MDHAPL: Unable to clamp the slipsheet on top of the plate in bay <bay>   Media Handler (APL)
47636   MDHAPL: The media quantity cannot be estimated ( bay <bay> ), <reason>   Media Handler (APL)
47637   MDHAPL: The plate stack is positioned too far forward ( bay <bay> )   Media Handler (APL)
47638   MDHAPL: An invalid float bar position of <position> mm was specified, range is <min position> to <max position>   Media Handler (APL)
47639   MDHAPL: Plate not positioned correctly on the transfer table.   Media Handler (APL)
47640   MDHAPL: The pusher has not reached the handoff position   Media Handler (APL)
47641   MDHAPL: The plate stack has exceeded the maximum height ( bay <bay> )   Media Handler (APL)
47642   MDHAPL: The float bar has insufficient range, the plate stack is too low ( bay <bay> )   Media Handler (APL)
47643   MDHAPL: The <sensor> sensor appears to have failed, <reason>   Media Handler (APL)
47644   MDHAPL: The slipsheet trajectory could not be calculated   Media Handler (APL)
47800   MDH: Media was detected on the <location> of the <hardware>, however it was not expected   Media Handler
47801   MDH: Unable to move <name of hardware trying to move> because <name of hardware in the way> is in the way   Media Handler
47802   MDH: Unable to move <name of hardware trying to move> because <name of hardware reserving the area the way> is currently reserving the area requested   Media Handler
47803   MDH: Sensor calibration failed because not all the sensors were triggered   Media Handler
47804   MDH: Sensor calibrate failed because some of the sensors were triggered prior to calibration   Media Handler
47805   MDH: <operation name> is waiting for media to finish imaging and be unloaded from the drum before continuing   Media Handler
47806   MDH: Slip sheet unexpectedly detected in cassette, cassette was setup not to use slip sheets   Media Handler
47807   MDH: <motor name> stepper motor did not reach or remain on the sensor it was searching for [<I/O name>]   Media Handler
47900   MDH: Open the cassette doors   Media Handler
47901   MDH: Pull out slip sheet bin to unload position   Media Handler
47902   MDH: Push slip sheet bin in until it latches   Media Handler
47903   MDH: Close the cassette doors   Media Handler
47904   MDH: Slip sheet bin is full, empty slip sheet bin   Media Handler
47905   MDH: Slip sheet bin locking pin extend timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
47906   MDH: Slip sheet bin locking pin retract timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
47907   MDH: Slip sheet bin <Bin> is not valid   Media Handler
47908   MDH: Cannot change the warning count in slip sheet bin <Bin>   Media Handler
47909   MDH: Cannot change the full count in slip sheet bin <Bin>   Media Handler
47910   MDH: Slip sheet bin cannot initialize because the picker area is currently reserved by the picker   Media Handler
47911   MDH: Slip sheet bin is full, open the cassette doors to unload   Media Handler
48000   MDH: Shuttle is unable to align media, ensure that there are <Number of stacks> stack(s) on the shuttle   Media Handler
48001   MDH: Shuttle pinch rollers open timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
48002   MDH: Shuttle pinch rollers close timeout: Failed to <Action> sensor. [<I/O name>]   Media Handler
48003   MDH: Cannot move the shuttle if the pinch rollers are closed   Media Handler
48004   MDH: Unlock doors and remove media from the shuttle   Media Handler
48005   MDH: Shuttle failed to move media to the pinch rollers sensors (prepare transfer), check <Media location>   Media Handler
48006   MDH: Shuttle failed to move media to the loadtable, check <Media location>   Media Handler
48007   MDH: Shuttle cannot initialize because the picker area is currently reserved by the picker   Media Handler
48008   MDH: Shuttle detected an underlying slip sheet, check <Media location> media   Media Handler
48101   XAC: Device alarm active   X-Axis Controller Interface
48102   XAC: Sensor limit reached   X-Axis Controller Interface
48103   XAC: Command was cancelled by the user   X-Axis Controller Interface
48104   XAC: Command sent to the device is not supported   X-Axis Controller Interface
48105   XAC: The command was rejected by the device   X-Axis Controller Interface
48106   XAC: The command timed out   X-Axis Controller Interface
48107   XAC: Receive buffer overflow, unable to process packet   X-Axis Controller Interface
48108   XAC: Component busy, not able to process new command   X-Axis Controller Interface
48109   XAC: An internal firmware error occurred   X-Axis Controller Interface
48110   XAC: Protocol Communications Error: Packet was too small   X-Axis Controller Interface
48111   XAC: Protocol Communications Error: Packet is wrong size   X-Axis Controller Interface
48112   XAC: Protocol Communications Error: No match for reply Packet   X-Axis Controller Interface
48113   XAC: Protocol Communications Error: Unknown type of reply Packet   X-Axis Controller Interface
48114   XAC: Protocol Communications Error: Illegal reply packet header   X-Axis Controller Interface
48115   XAC: Protocol Communications Error: Unknown reply packet header   X-Axis Controller Interface
48116   XAC: Internal Firmware Error: Internal Message Queue resources exhausted   X-Axis Controller Interface
48117   XAC: THINK DEVICE Error: Device Alarm   X-Axis Controller Interface
48118   XAC: THINK DEVICE Error: Limit reached   X-Axis Controller Interface
48119   XAC: THINK DEVICE Error: Operation Cancelled   X-Axis Controller Interface
48120   XAC: THINK DEVICE Error: Command Unsupported   X-Axis Controller Interface
48200   COM: Internal firmware error - COM driver   CANopen Master Communication Protocol Driver
48201   COM: Internal firmware error - COM driver   CANopen Master Communication Protocol Driver
48202   COM: CAN Transmit Queue is Full - COM driver   CANopen Master Communication Protocol Driver
48203   COM: CANopen SDO channels are all in use - COM driver   CANopen Master Communication Protocol Driver
48204   COM: Failure opening SDO channel to CANopen node - COM driver   CANopen Master Communication Protocol Driver
48205   COM: Timeout performing CANopen communication - COM driver   CANopen Master Communication Protocol Driver
48206   COM: SDO abort occuring performing CANopen SDO communication - COM driver   CANopen Master Communication Protocol Driver
48207   COM: Unknown SDO CANopen communication error - COM driver   CANopen Master Communication Protocol Driver