636-00186B
ECO CA15814

Note: Only install V1.09e on devices that support it, through controlled releases.

This patch addresses the issue where the firmware becomes corrupted and a subsystem is not available.

For details on the changes made to this version, see the TH2 Firmware V1.09 Release Notes

636-00186A
ECO CA13399

This version has been replaced by 1.09e due to a TH2 hardware change.  In all cases, use 1.09e in place of 1.09c.

Note: Version 1.09c has been disabled; do not use.

636-00164B
ECO CA14724

Note: Only install V1.08j on devices that support it, through controlled releases.

This patch addresses the previous focus learn failures in 1.08i.

For details on the changes made to this version, see the v1.08j Release Notes

636-00162A
ECO CA10714

Note: Only install V1.07b on devices that support it, through controlled releases.

For details on the changes made to this version, see the v1.07b Release Notes

636-00156A
ECO CA10062

Note: Only install V1.06 on devices that support it, through controlled releases.

Implemented:
Added greater control of focus laser power for sensitive media.

For details on the changes made to this version, see the v1.06 Release Notes

636-00107B
ECO CA08812

Note: Only install V1.05d on devices that support it, through controlled releases.

Implemented:

• Improved error messaging
• Beam correction utility to extend head life
• Added support for high addressability heads

For details on the changes made to this version, see the v1.05d Release Notes

636-00053B-A
ECO CA03674

Note: Only install V1.04d on devices that support it, through controlled releases.

This version is functionally equivalent to 1.04c.

Implemented:

• hardware fix for new focus diode
• automatic gain control to keep focus sum constant
• allow the MCE to turn the focus laser on and off
• fix focus timeout calculations

For details on the changes made to this version, refer to the V1.04d Release Notes

636-00053A-A
ECO CA03435

This version has been replaced by 1.04d, due to a TH2 hardware change.  In all cases, use 1.04d in place of 1.04c.

Implemented:

• automatic gain control to keep focus sum constant
• allow the MCE to turn the focus laser on and off
• fix focus timeout calculations

For details on the changes made to this version, refer to the V1.04c Release Notes

636-00047A-B
ECO CA03674

Note: Only install V1.03c on devices that support it, through controlled releases.

This version is functionally equivalent to 1.03b.

Implemented:

• hardware fix for new focus diode
• edge detection on improperly coated media
• display table when focus learn fails
• fix clamp shadow handling
• fix mismatch errors during gapless imaging
• update to Xilinx 0.30

For details on the changes made to this version, refer to the V1.03c Release Notes

636-00047A-A
ECO CA01957

This version has been replaced by 1.03c, due to a TH2 hardware change.  In all cases, use 1.03c in place of 1.03b.

V1.03b contains only minor changes from V1.02.  Full regression testing is not required when updating controlled releases from V1.02 to V1.03b. Please refer to the V1.02 documentation if upgrading from V1.01h or earlier to V1.03b.

Implemented:

• edge detection on improperly coated media
• display table when focus learn fails
• fix clamp shadow handling
• fix mismatch errors during gapless imaging
• update to Xilinx 0.30

For details on the changes made to this version, refer to the V1.03b Release Notes

636-00046B-B
ECO CA03674

This version is functionally equivalent to 1.02.

Implemented:

• hardware fix for new focus diode
• Creo Exposure Head (CEH) Interface - with CEH, head parameters are no longer accessible through the MCE interface, access them through the head interface instead (e.g. - use set med under redirection instead of set hdm)
• support for additional focus startup sequences
• support for bidirectional imaging
• support for staggered seams
• featureless edge detect
• support for P22/P33 imaging

For details on the changes made to this version, refer to the V1.02b Release Notes

For the upgrade procedures, refer to version 1.01c Release Notes.

636-00046B-A
ECO CA00924

This version has been replaced by 1.02b, due to a TH2 hardware change.  In all cases, use 1.02b in place of 1.02.

Implemented:

• Creo Exposure Head (CEH) Interface - with CEH, head parameters are no longer accessible through the MCE interface, access them through the head interface instead (e.g. - use set med under redirection instead of set hdm)
• support for additional focus startup sequences
• support for bidirectional imaging
• support for staggered seams
• featureless edge detect
• support for P22/P33 imaging

For details on the changes made to this version, refer to the V1.02 Release Notes

ECO CA03674

• This version is functionally equivalent to 1.01h.
• This version includes the hardware fix for the new focus diode.
• This version was changed to reset the hotlink buffers, which prevents corruption of the image (this is a "kludge" for the "swath data reversal" problem)
• Version 1.01i Release Notes

For the upgrade procedures, refer to version 1.01c Release Notes.

ECO CA00343

• This version was changed to reset the hotlink buffers, which prevents corruption of the image (this is a "kludge" for the "swath data reversal" problem)

For details on the changes made to this version, refer to the V1.01h Release Notes

ECO E751

• This version enables the transmission of WLP burst data to prevent corruption of the laser diode setpoint temperature (PR #556)

For details on the changes made to this version, refer to the V1.01f Release Notes

This is a patch release that fixes the following problems:

• Disable the data cable system fault for version B boards (no PR).
• Fix an "interrupt hole" causing the beam-pointing control loop to be disabled (PR #509).

This is a patch release that fixes the following problems:

• Allow for 50ms of settling time before attempting to read the beam-balance sensor (no PR).
• Attempt to correct the hardware state by opening and then closing the shutter (no PR).
• Fix Xilinx bugs that cause problems selecting pixels, while calculating the stroke profile (version B boards only) (no PR).
• Update the defaults for the beam-pointing PID gains (no PR).
• Focus should function if the voltage is in a warning state (no PR).
• Adjust the warning and alarm ranges for the voltages (no PR).
• Increase the timeout for the focus learn (no PR).
• Fix bugs clearing the beam-pointing actuator over-current state (no PR).

ECO E620

Warning: Do not use this release with heads that have control board 2 (primarily DOP heads). Refer to the release notes for more information.

This is a major release that implements the following changes:

• Staccato support (no PR)
• "Gapless" imaging (no PR)

Release Notes

• Focus will not abort if the voltage levels are in normal or warning states. Focus will abort only if one of the voltage levels is in an alarm state (no PR).
• Adjust the warning and alarm ranges for the voltages (no PR).

For the upgrade procedure, refer to version 1.01c Release Notes.

• Fix a focus bug resulting in the disabling of error checking (no PR)

• Disable the data cable and data overflow warning faults for version B boards (PR 487)

• Implement temporary support for Staccato (no PR)

/E379

• Increase the timeout for detecting WLP burst data (PR #445)
• Fix problems with the focus effective gap algorithm caused by noise (PR #444)
• Fix a bug preventing changes to the NVS parameter med focuslasermode from taking effect immediately (no PR)

Release Notes

/E371

Release Notes