Home | Contact Us | Submit Troubleshooting Info | Search | Help


    Output | Software Solutions | Proofing | Color, Screening and Calibration | Scanning | Digital Photography | Consumables | POS

MPE NVS Parameters

See also Search Form

This content is generated by scripts that pull information directly from Firmware Engineering's support site. The scripts were last run: 16 Jul 2008 17:30:13

Parameter Family Parameter Name
al     coff (clamp_offset)
al     ldvel (load_vel)
al     lepos (le_pos)
al     lr (load_ramp_sensor)
al     lrtp (load_ramp_tilt_pos)
al     ppos (park_pos)
al     soff (sensor_offset)
al     uldvel (unload_vel)
aldly     le (le_delay)
aldly     roller (roller_delay)
aldly     sensor (sensor_delay)
aldly     te (te_delay)
aldly     tes (te_sensor_delay)
carriage     accel (max_accel)
carriage     again (driver_accel_gain)
carriage     bflearn (blank_focus_learn)
carriage     bfrlearn (blank_focus_relearn)
carriage     coff (cos_offset)
carriage     cph (centre_plate_to_home)
carriage     eaccel (edge_search_accel)
carriage     eatt (edge_attempts)
carriage     esearch (edge_narrow_search)
carriage     espeed (edge_speed)
carriage     gearing (srot_per_lrot)
carriage     hgain (driver_hold_gain)
carriage     ispeed (init_speed)
carriage     kspeed (knee_speed)
carriage     mgain (driver_move_gain)
carriage     mspeed (max_speed)
carriage     msspeed (max_skip_speed)
carriage     mswidth (min_skip_width)
carriage     mtravel (max_travel)
carriage     period (accel_period)
carriage     pgain (driver_plot_gain)
carriage     pitch (mil_per_lrot)
carriage     psteps (plot_accel_steps)
carriage     scyc (steps_per_scyc)
carriage     skip (blank_skipping)
carriage     soff (sine_offset)
carriage     steps (steps_per_srot)
carriage     wsearch (edge_wide_search)
config     al (alexist)
config     conv (conveyor)
config     engine (engexist)
config     msz (mscan_size)
config     owner (ownername)
config     res (resolutions)
config     serial (serialno)
config     speed (speed)
config     ssz (sscan_size)
config     type (machtype)
config     ver (version)
dpe     mzs (mscan_zone_size)
drum     chkfly (check_flyoff)
drum     dfrict (drive_friction)
drum     dgh (deriv_gain_hall)
drum     dgp (deriv_gain_posn)
drum     dgs (deriv_gain_soft)
drum     dgv (deriv_gain_vel)
drum     dgvt (deriv_gain_vel_test)
drum     diam (nominal_diameter)
drum     doff (drive_offset)
drum     dt (drum_type)
drum     epos (edge_position)
drum     gear (drum_gear_ratio)
drum     hppr (hall_pulses_per_rot)
drum     igh (integ_gain_hall)
drum     igp (integ_gain_posn)
drum     igs (integ_gain_soft)
drum     igv (integ_gain_vel)
drum     igvt (integ_gain_vel_test)
drum     iner (drum_inertia)
drum     maxdiff (max_hall_vs_enc_diff)
drum     mtcn (motor_torque_const)
drum     mtol (move_tolerance)
drum     pacc (position_accel)
drum     pgh (prop_gain_hall)
drum     pgp (prop_gain_posn)
drum     pgs (prop_gain_soft)
drum     pgv (prop_gain_vel)
drum     pgvt (prop_gain_vel_test)
drum     ted (tach_encoder_direction)
drum     tpr (tach_pulses_per_rot)
drum     vacc (velocity_accel)
drum     vgp (vel_gain_posn)
gc     cbp (cal_beam_pos)
gc     engc (enable_gc)
gc     eno (enable_orthog)
gc     ftc (frame_temp_coef)
gc     lstc (leadscrew_temp_coef)
gc     mbp (measure_beam_pos)
gc     msca (mscan_scale_adjust)
gc     mss (mscan_shift)
gc     mssa (mscan_shift_adjust)
gc     ortho (orthog_adjust)
gc     prot (plate_rotate)
gc     sprot (small_plate_rotate)
gc     ssca (sscan_scale_adjust)
gc     sss (sscan_shift)
gc     tinc (track_profile_inc)
gc     trk (track_profile)
gc     vsprot (very_small_plate_rotate)
media     dopt (debris_option)
media     esp (exp_series_pattern)
media     inv (invert)
media     mcode (media_code)
media     mdt (max_door_time)
media     name (media_type_name)
media     pcode (processor_code)
media     proc (processor)
media     sens (default_sensitivity)
media     tc (temp_coef)
media     thk (default_thickness)
mode     dpi (rip_dpi)
mode     edge (find_edge)
mode     esi (exp_series_step)
mode     ess (exp_series_start)
mode     exp (exposure_adjust)
mode     ikb (ink_key_bits)
mode     ikms (mscan_sample_size)
mode     ikss (sscan_sample_size)
mode     ikt (ink_key_transitions)
mode     inv (invert)
mode     is (image_side)
mode     mir (mirror)
mode     mis (mscan_image_size)
mode     msa (mscan_scale_adjust)
mode     msd (mscan_duplicate)
mode     mssa (mscan_shift_adjust)
mode     pps (pixels_per_stroke)
mode     rbo (rip_byte_order)
mode     skr (skip_rotations)
mode     sl (series_length)
mode     ss (stroke_shift_pixels)
mode     ssa (sscan_scale_adjust)
mode     ssd (sscan_duplicate)
mode     sssa (sscan_shift_adjust)
mode     sw (series_strip_width)
oldmedia     escan (extra_scanlines)
oldmedia     esp (exp_series_pattern)
oldmedia     inv (invert)
oldmedia     ltol (tolerance_limit)
oldmedia     mcode (media_code)
oldmedia     name (media_type_name)
oldmedia     proc (processor)
oldmedia     rexp (reject_exp_time)
oldmedia     sens (default_sensitivity)
oldmedia     sm (sensitivity_slope)
oldmedia     srt (sens_recal_thresh)
oldmedia     stol (stroke_tolerance)
oldmedia     tc (temp_coef)
oldmedia     thk (default_thickness)
sat     cbec (cb_err_chk)
sat     et (engine_temp)
sat     fsc0 (FullScaleCal0)
sat     fsc1 (FullScaleCal1)
sat     fsc2 (FullScaleCal2)
sat     fsc3 (FullScaleCal3)
sat     lst (leadscrew_temp)
sat     ltpmax (ldr_testpoint_max)
sat     ltpmin (ldr_testpoint_min)
sat     luec (lu_err_chk)
sat     p0v (Proc0Vel)
sat     p1v (Proc1Vel)
sat     pdec (pd_err_chk)
sat     ppec (pp_err_chk)
sat     ptpmax (pkr_testpoint_max)
sat     ptpmin (pkr_testpoint_min)
sat     pvg (pkr_vac_gain)
sat     pvo (pkr_vac_offset)
sat     st0 (spare_temp0)
sat     st1 (spare_temp1)
sat     state (state)
sat     tr0 (ThermistorRef0)
sat     tr1 (ThermistorRef1)
sat     tr2 (ThermistorRef2)
sat     tr3 (ThermistorRef3)
sat     uvg (unld_vac_gain)
sat     uvo (unld_vac_offset)
sat     uvt (uvac_threshold)
sat     zbrake (z_brake_err_chk)
sat     zsc0 (ZeroScaleCal0)
sat     zsc1 (ZeroScaleCal1)
sat     zsc2 (ZeroScaleCal2)
sat     zsc3 (ZeroScaleCal3)
state     aif (post_imaging_faults)
state     arch (nvs_modified)
state     bay (bay_index)
state     btime (total_busy_time)
state     ci (total_cancelled_images)
state     cmd (command)
state     door (door_opened)
state     double (double_edge_count)
state     dtime (time_door_open)
state     ecode (error_code)
state     epos (edge_position)
state     error (error_status)
state     expd (exposed_flag)
state     fail (failed_edge_count)
state     false (false_edge_count)
state     fcnt (fault_count)
state     fcnt (fault_reset_count)
state     fi (total_failed_images)
state     flen (total_fault_length)
state     ftime (most_recent_time)
state     head (head_type)
state     id (image_id)
state     if (imaging_faults)
state     msz (mscan_size)
state     order (load_order)
state     pcnt (pwr_rst_count)
state     pib (pre_img_bay_faults)
state     pif (pre_imaging_faults)
state     pl (plate_loading)
state     pp (plates_picked)
state     ptime (low_pressure_time)
state     reject (total_reject_images)
state     ret (retrace_count)
state     sens (sensitivity)
state     ssz (sscan_size)
state     state (state)
state     status (status)
state     stime (total_suspended_time)
state     te (tec_on_drum)
state     thk (plate_thickness)
state     ti (total_ws_images)
state     tmax (max_temperature)
state     tmin (min_temperature)
state     total (total_ws_images)
state     ttime (total_on_time)
state     type (media_type)
status     mask (status_mask)
sys     asp (asynch_series_period)
sys     asr (abort_on_scsi_reset)
sys     ast (asynch_series_pause)
sys     bench (bench_mode)
sys     chin (chiller_installed)
sys     cpy (chars_per_yield)
sys     dbhs (dblower_high_stop)
sys     dbin (dblower_installed)
sys     dbls (dblower_low_stop)
sys     dblw (dblower_low_warning)
sys     dlys (delay_scsi_start)
sys     eis (extra_invert_stroke)
sys     ewc (echo_ws_commands)
sys     ewd (echo_watchdog)
sys     ews (echo_ws_status)
sys     hi (head_installed)
sys     hpd (high_pwr_drives_inst)
sys     ism (image_size_margin)
sys     load (load_plate)
sys     m1 (macro1)
sys     m2 (macro2)
sys     m3 (macro3)
sys     maxis (max_image_size)
sys     maxssz (max_subscan_size)
sys     mb1 (must_be_1)
sys     newd (new_drum_speed)
sys     ntau (nco_filter_tau)
sys     ntu (nco_tach_update)
sys     pgain (pll_gain)
sys     pswd (password)
sys     s1 (stroke_stats1_mode)
sys     s2 (stroke_stats2_mode)
sys     sbaud (scon_baudrate)
sys     scon (scon_installed)
sys     sid (scsi_id)
sys     sig (display_signatures)
sys     sn (serial_number)
sys     spt (sys_pressure_thresh)
sys     track (report_tracking)
sys     tstate (state_filter_length)
sys     tstatus (status_filter_length)
sys     tstk (stroke_update_interval)
sys     wd (ws_watchdog_timeout)
sys     wsb (ws_baud_rate)
temp     b1 (integer1)
temp     b2 (integer2)
temp     b3 (integer3)
temp     b4 (integer4)
temp     l1 (lword1)
temp     l2 (lword2)
temp     l3 (lword3)
temp     l4 (lword4)
temp     w1 (word1)
temp     w2 (word2)
temp     w3 (word3)
temp     w4 (word4)
verbose     alcmd (al_command)
verbose     all (all)
verbose     carriage (carriage)
verbose     datalink (datalink)
verbose     drum (drum)
verbose     eh (exp_head)
verbose     image (image)
verbose     monitor (monitor)
verbose     msg (messages)
verbose     plot (plot_mgr)
verbose     redirect (redirect)
verbose     sys (system)
verbose     timer (timer)
verbose     ws (workstation)

    Copyright © 2005 Creo Inc. All rights reserved. Confidential. Back to top.