Home | Contact Us | Submit Troubleshooting Info | Search | Help
Output | Software Solutions | Proofing | Color, Screening and Calibration | Scanning | Digital Photography | Consumables | POS
Home | Contact Us | Submit Troubleshooting Info | Search | Help
Output | Software Solutions | Proofing | Color, Screening and Calibration | Scanning | Digital Photography | Consumables | POS
See also
This content is generated by scripts that pull information directly from Firmware Engineering's support site. The scripts were last run: 16 Jul 2008 17:30:08
| Number | Error Message | |
|---|---|---|
| 00000 | MISC: | |
| 00001 | MISC: Reserved | |
| 00002 | MISC: Reserved | |
| 00003 | MISC: Reserved | |
| 00004 | MISC: Reserved | |
| 00005 | MISC: Reserved | |
| 00006 | MISC: Reserved | |
| 00007 | MISC: Reserved | |
| 00020 | MISC: Specified test is not defined | |
| 00021 | MISC: Workstation communications lost | |
| 00030 | MISC: Requested command is not defined | |
| 00100 | MISC: MPE Code checksum is faulty | |
| 00101 | MISC: LCA module checksum is faulty | |
| 00102 | MISC: LCA module incompatable format | |
| 00103 | MISC: Module not found in version list | |
| 00104 | MISC: Firmware module checksum is faulty | |
| 00105 | MISC: Error opening firmware module | |
| 00106 | MISC: Invalid or unneeded code bundled with firmware | |
| 00107 | MISC: Missing required code in the firmware bundle | |
| 00108 | MISC: Product version not found in version list | |
| 00109 | MISC: Invalid version of overwriting pattern | |
| 00200 | MISC: Code bank selected for loadingis current code bank | |
| 00201 | MISC: Flash memory program failed | |
| 00202 | MISC: Address <hex address> out of memory bank range | |
| 00203 | MISC: Unsupported memory type detected | |
| 00204 | MISC: Flash memory erase failed | |
| 00500 | MISC: Temperature log: Engine = <Celcius x 10> Leadscrew = <Celcius x 10> | |
| 00501 | MISC: Password not set! | |
| 00502 | MISC: NVS modified and saved, but not backed up! | |
| 00511 | MISC: Dongle not responding | |
| 00512 | MISC: Config: %s %s owner %s | |
| 01000 | RESET: cause unknown | |
| 01001 | RESET: induced by test submodule | |
| 01002 | RESET: induced by RESET opcode, possible warm reset requested at monitor | |
| 01004 | RESET: induced by loss of clock | |
| 01016 | RESET: induced by halt monitor | |
| 01032 | RESET: induced by software watchdog, possible cold reset requested at monitor | |
| 02000 | NVS: checksum error in <NVS subsystem> calibration block | |
| 02040 | NVS: checksum error in <NVS subsystem> configuration block | |
| 02080 | NVS: checksum error in mode <number> table | |
| 02200 | NVS: low battery in NVS detected | |
| 02201 | NVS: NVS automatically upgraded to version 2 | |
| 02202 | NVS: subscan size nvs config parameter is invalid | |
| 03000 | WSCOMM: All faults cleared | |
| 03001 | WSCOMM: Invalid command letter | |
| 03002 | WSCOMM: Parameter syntax error | |
| 03003 | WSCOMM: Defined WS command is currently unsupported | |
| 03004 | WSCOMM: Character pacing timeout, WS transmitting too slowly | |
| 03005 | WSCOMM: too many characters in command string | |
| 03006 | WSCOMM: Could not open serial communications interface for workstation | |
| 03007 | WSCOMM: Resume or clear received when not suspended | |
| 03008 | WSCOMM: Command received for idle image ID | |
| 03009 | WSCOMM: Specified image ID is already active | |
| 03010 | WSCOMM: Maximum active image commands surpassed | |
| 03011 | WSCOMM: Resolution specified is not available | |
| 03012 | WSCOMM: Already aborting | |
| 03014 | WSCOMM: Abort received when no command active | |
| 03015 | WSCOMM: Already imaging | |
| 03016 | WSCOMM: Recorder is flushing, can't accept new commands | |
| 03017 | WSCOMM: Door is open | |
| 03018 | WSCOMM: Door is closed | |
| 03019 | WSCOMM: ABORT switch on | |
| 03020 | WSCOMM: ABORT switch off | |
| 03021 | WSCOMM: Operation aborted at recorder - check that abort switch is released | |
| 03022 | WSCOMM: Operation aborted by workstation | |
| 03023 | WSCOMM: ABORT complete | |
| 03024 | WSCOMM: Abort request not heeded within timeout, possible hung subsystem | |
| 03025 | WSCOMM: Task(s) <task codes> did not finish initializing on time | |
| 03026 | WSCOMM: Operation preempted | |
| 03027 | WSCOMM: Cassette bay door open | |
| 03028 | WSCOMM: Cassette bay door closed | |
| 03047 | WSCOMM: Resolution does not exist | |
| 03048 | WSCOMM: Image too wide for plate | |
| 03055 | WSCOMM: Workstation software error - Invalid packet number | |
| 03056 | WSCOMM: Workstation software error - Invalid total packets number | |
| 03057 | WSCOMM: Workstation software error - Out of sequence packet received | |
| 03058 | WSCOMM: Workstation software error - Invalid packet length | |
| 03059 | WSCOMM: Workstation software error - Invalid Media Imaging Mode ID (MIMID) | |
| 03060 | WSCOMM: Packet fails CRC check | |
| 03061 | WSCOMM: Total packet data exceeding firmware buffer capacity | |
| 04001 | MSG: Command parameter error | |
| 04002 | MSG: Parameter is out of range | |
| 04003 | MSG: Defined command is currently unsupported | |
| 04004 | MSG: Requested test pattern not defined | |
| 04005 | MSG: <subsystem> is already reserved | |
| 04006 | MSG: Reserved message in message pool | |
| 04007 | MSG: Task releasing message owned by another task | |
| 04008 | MSG: Task releasing unreserved message | |
| 04009 | MSG: Task sending message owned by another task | |
| 04010 | MSG: Task sending unreserved message | |
| 04011 | MSG: Task received message that was not sent | |
| 04012 | MSG: Reserved string in string pool | |
| 04013 | MSG: Task releasing unreserved string | |
| 04014 | MSG: Task releasing string owned by another task | |
| 04015 | MSG: Task reserving released string | |
| 04016 | MSG: <task name> timed out while waiting for command <hex command code> | |
| 04017 | MSG: <task name> received an invalid command (command = <hex command code>) | |
| 04018 | MSG: Wrong number of parameters | |
| 04019 | MSG: Inactive list sent | |
| 04020 | MSG: Unexpected list type sent | |
| 04021 | MSG: Invalid list entry number sent - Possible version incompatabilities | |
| 04022 | MSG: Plot mode not specified before plot parameters | |
| 04024 | MSG: Task received msg with unexpected id (code = %X) | |
| 04028 | MSG: suspended - waiting for Resume or Clear | |
| 04029 | MSG: plate thickness too large | |
| 04030 | MSG: one or both plate dimensions too large | |
| 04031 | MSG: media type out of range | |
| 04032 | MSG: one or both plate dimensions too small | |
| 04034 | MSG: media %d not supported | |
| 06000 | DRUM: Timeout on drum operation | |
| 06001 | DRUM: Illegal command state machine state | |
| 06002 | DRUM: Timeout waiting for drum move | |
| 06003 | DRUM: Received invalid command | |
| 06004 | DRUM: drum not initialized - can't execute that command | |
| 06005 | DRUM: Unexpected status returned from function | |
| 06006 | DRUM: Timeout during active braking | |
| 06007 | DRUM: Timeout on velocity settling | |
| 06008 | DRUM: Timeout on velocity acceleration | |
| 06009 | DRUM: Sample interrupt failure | |
| 06011 | DRUM: Servo amp fault | |
| 06012 | DRUM: Cable from motherboard to drum servo amp not detected | |
| 06013 | DRUM: Index not detected | |
| 06014 | DRUM: Extra Tach A pulse detected | |
| 06015 | DRUM: Missing Tach A pulse | |
| 06016 | DRUM: Extra Tach B pulse detected | |
| 06017 | DRUM: Missing Tach B pulse | |
| 06018 | DRUM: Drive direction incorrect - check motor wiring | |
| 06019 | DRUM: Tach encoder cable not detected | |
| 06020 | DRUM: Aborted | |
| 06021 | DRUM: Timeout on hold | |
| 06022 | DRUM: Motor current exceeded limit | |
| 06023 | DRUM: Velocity error - drum rotation blocked or PID gain settings wrong | |
| 06024 | DRUM: Position error is greater than 1000 ticks | |
| 06025 | DRUM: Hall velocity error - drum rotation blocked or PID gain settings wrong | |
| 06026 | DRUM: Timeout waiting for TPU hall sensor PW measurement | |
| 06027 | DRUM: Plate not loaded correctly on drum, obstruction detected below LEC actuator | |
| 06028 | DRUM: ALE actuators on drum | |
| 06029 | DRUM: Hall mode overspeed error - possible TPU failure | |
| 06030 | DRUM: Drum hall velocity does not match encoder velocity to within tolerance. | |
| 06031 | DRUM: Drum is spinning. | |
| 06033 | DRUM: Index detected prematurely - clean encoder disc or re-align encoder | |
| 06034 | DRUM: Drum won't settle with zero torque applied - requires drum cal | |
| 06036 | DRUM: Drum Position error during Velocity mode, (check acceleration setting) | |
| 06037 | DRUM: Drum velocity greater than xx rpm in Position mode, possible runaway | |
| 06038 | DRUM: LCA tick counter annomaly, premature index or spurious counter reset | |
| 06039 | DRUM: Drum Position error during Velocity mode, (extra index possible cause, check monitor values) | |
| 06040 | DRUM: Encoder counted extra ticks | |
| 06041 | DRUM: Index occurred at xx, more than 3 ticks before normal ticks per rotation | |
| 06042 | DRUM: Hall velocity error - more than 20 percent during drum init. | |
| 07000 | CARRIAGE: Limit switches reporting carriage is both HOME and AWAY | |
| 07001 | CARRIAGE: stuck in HOME position | |
| 07002 | CARRIAGE: stuck in AWAY position | |
| 07003 | CARRIAGE: unexpectedly arrived at HOME position | |
| 07004 | CARRIAGE: unexpectedly arrived at AWAY position - image size may have been too large | |
| 07005 | CARRIAGE: operation timed out | |
| 07006 | CARRIAGE: timed out while waiting for LCA position | |
| 07007 | CARRIAGE: position register not accurate | |
| 07008 | CARRIAGE: LCA's not configured at startup | |
| 07009 | CARRIAGE: ALE not taken out of reset | |
| 07010 | CARRIAGE: Unexpected error: 0x%x | |
| 07011 | CARRIAGE: could not find edge of platecheck that plate size is entered correctly | |
| 07012 | CARRIAGE: did not reach target speed | |
| 07013 | CARRIAGE: step synth position register reserved | |
| 07015 | CARRIAGE: Head Stage is at it's away position, unsafe to move carriage | |
| 07016 | CARRIAGE: ALE board timed out during carriage position read | |
| 07017 | CARRIAGE: Carriage state error. Current state: <description>, jog_count = <n> JOG = <number> PLOT = <number> | |
| 07018 | CARRIAGE: Carriage illegal dest. Current %lu, Dest %lu Stop Dist %lu | |
| 07019 | CARRIAGE: Specified Speed exceeds maximum of %lu | |
| 08000 | PROC: Processor not present or turned off | |
| 08001 | PROC: Processor is not ready | |
| 08002 | PROC: Processor fault requires immediate attn. | |
| 08003 | PROC: Processor warning will need attention | |
| 08004 | PROC: Processor type unknown | |
| 08005 | PROC: Illegal processor number used | |
| 10012 | HARDWARE: Carriage limit switch | |
| 10019 | HARDWARE: ALE is not plugged in | |
| 10020 | HARDWARE: DPE is not plugged in | |
| 10022 | HARDWARE: MPE LCA's not configured at startup | |
| 10023 | HARDWARE: DPE will not initialize, may be stuck in reset | |
| 10025 | HARDWARE: DPE LCA's not configured at startup | |
| 10026 | HARDWARE: Incorrect DPE version installed | |
| 10050 | HARDWARE: RAM DAC Incrementing Address Test fail - Address = <fault address>, Write data = <hex data>, Readdata = <hex data> | |
| 10051 | HARDWARE: DPE failure - dpath control write = <hex data>, read = <hex data> | |
| 10060 | HARDWARE: External Debris Blower Filters Not Present | |
| 10061 | HARDWARE: External Debris Blower Filters Full | |
| 10062 | HARDWARE: External Debris Blower Filters Almost Full (Vacuum Level %d is below %d) | |
| 10063 | HARDWARE: External Debris Blower System Blocked (Vacuum Level %d is above %d) | |
| 10064 | HARDWARE: External Debris Blower Not Connected or Filters Full (Vacuum Level %d is below %d) | |
| 10065 | HARDWARE: DBlower Filter Fault. | |
| 11000 | CABLE: HA-BP cbl, Carriage Home/Away | |
| 11002 | CABLE: EH-BP: Exposure Head - Backplane | |
| 11003 | CABLE: TE-BP: Tach Encoder - Backplane | |
| 11004 | CABLE: MD-BP: Drum Motor - Backplane | |
| 11504 | CABLE: SPR-BP | |
| 12000 | POWER: ALE +12V | |
| 12001 | POWER: ALE -12V | |
| 12002 | POWER: Carriage power | |
| 12006 | POWER: Carriage Amp Fault | |
| 12007 | POWER: Exposure Head power | |
| 12008 | POWER: Drum Amp Fault | |
| 12801 | POWER: ALE -2V | |
| 13000 | EHBOOT: internal message timeout | |
| 13001 | EHBOOT: datalink terminated the program sequence prematurely | |
| 13002 | EHBOOT: format error detected during data transfer | |
| 13003 | EHBOOT: sumcheck error detected during data transfer | |
| 13004 | EHBOOT: datalink programming sequence taking too long | |
| 13005 | EHBOOT: LOADER echo mismatch during bootstrap sequence | |
| 13006 | EHBOOT: LOADER not echoed during bootstrap sequence | |
| 13007 | EHBOOT: no break detected after forcing head into bootstrap mode | |
| 13008 | EHBOOT: cannot perform requested operation, no LOADER present | |
| 13009 | EHBOOT: LOADER prompt for next primitive did not arrive | |
| 13010 | EHBOOT: communications error | |
| 13011 | EHBOOT: failed to program location <hex data> with data <hex data> | |
| 13012 | EHBOOT: failed to erase device, stopped at location <hex data> | |
| 13013 | EHBOOT: failed to respond to programming command | |
| 13014 | EHBOOT: Timeout on byte <byte #> while waiting for exposure head to complete response string | |
| 13015 | EHBOOT: ENQ expected and not received | |
| 13016 | EHBOOT: ACK expected and not received | |
| 13017 | EHBOOT: incorrect response length | |
| 13018 | EHBOOT: incorrect version length | |
| 13019 | EHBOOT: incorrect version response in byte <byte #> | |
| 13020 | EHBOOT: incorrect response address | |
| 13021 | EHBOOT: incorrect response data | |
| 14000 | SAT: Satellite error cleared | |
| 14001 | SAT: SPI system not initialized | |
| 14002 | SAT: Unknown Satellite Output Register: <hex number> | |
| 14003 | SAT: Satellite SW corrupted Buffer | |
| 14004 | SAT: Buffer Restore error during Output Command | |
| 14050 | SAT: QSPI error during configuration | |
| 14051 | SAT: Timeout during SPI enable | |
| 14052 | SAT: Timeout during QSPI disable | |
| 14053 | SAT: Timeout during SPI execution | |
| 14054 | SAT: SPI Mode Fault error | |
| 14055 | SAT: QSPI Update Watchdog timeout | |
| 14056 | SAT: <Satellite Board> Error: <Output Name> | |
| 14057 | SAT: Error Detection Error: Address <address>, Bit = <bit number> | |
| 14100 | SAT: Temperature Filter Error: Out of range | |
| 14101 | SAT: LUE Analog testpoint exceeded allowed maximum | |
| 14102 | SAT: LUE Analog testpoint exceeded allowed minimum | |
| 14103 | SAT: Engine Frame temperature out of range | |
| 14104 | SAT: Engine Leadscrew temperature out of range | |
| 14105 | SAT: Spare sensor 0 temperature out of range | |
| 14106 | SAT: Spare sensor 1 temperature out of range | |
| 14107 | SAT: Timeout waiting for conveyor roller speed to update | |
| 14108 | SAT: Timeout waiting for conveyor belt speed to update | |
| 14150 | SAT: Cassette Bay <bay number> invalid, autoloader currently configured for <max> bays | |
| 14151 | SAT: Cassette Bay <bay number> Error: <device> | |
| 14200 | SAT: PPE Analog testpoint exceeded allowed maximum | |
| 14201 | SAT: PPE Analog testpoint exceeded allowed minimum | |
| 14203 | SAT: Software error: invalid image task state %d in sat_update_lamps() | |
| 15062 | ALE: plate loaded incorrectly, remove plate from drum | |
| 15071 | ALE: remove plate from drum | |
| 15072 | ALE: remove plate partially on drum | |
| 15074 | ALE: trailing edge clamps failed to unlock | |
| 15075 | ALE: trailing edge clamps failed to lock | |
| 15076 | ALE: trailing edge clamps not on actuator | |
| 15077 | ALE: trailing edge clamps already on actuator, possible sensor or software error. | |
| 15078 | ALE: no plate on drum | |
| 15079 | ALE: timeout moving leading edge cylinder | |
| 15080 | ALE: timeout moving trailing edge cylinder | |
| 15082 | ALE: timeout moving roller cylinder | |
| 15503 | ALE: ALE board still in reset | |
| 15504 | ALE: ALE board not responding | |
| 15506 | ALE: command already in progress | |
| 15507 | ALE: Autoloader operation aborted | |
| 15508 | ALE: Autoloader not initialized | |
| 15509 | ALE: System air pressure too low! | |
| 15510 | ALE: Processor channel %d is invalid | |
| 15511 | ALE: not implemented yet | |
| 15520 | ALE: %s %d communication error | |
| 15521 | ALE: %s %d is busy | |
| 15522 | ALE: %s %d initialization error | |
| 15523 | ALE: %s %d not initialized | |
| 15524 | ALE: %s %d SW error: invalid PARAMETER | |
| 15525 | ALE: %s %d aborted while moving | |
| 15526 | ALE: %s %d SW error: invalid STATE | |
| 15528 | ALE: %s %d timed out while aborting | |
| 15531 | ALE: %s %d HOME limit switch is active | |
| 15532 | ALE: %s %d AWAY limit switch is active | |
| 15533 | ALE: %s %d timed out while homing | |
| 15534 | ALE: %s %d timed out while moving | |
| 15535 | ALE: please close access door | |
| 15539 | ALE: engine mount lock cylinders didn't move | |
| 15540 | ALE: move clamps to park position, then select RESUME | |
| 15542 | ALE: trailing edge clamps failed to unlock | |
| 15543 | ALE: trailing edge clamps failed to lock | |
| 15544 | ALE: trailing edge clamps not on actuator | |
| 15545 | ALE: trailing edge clamps on actuator | |
| 15546 | ALE: trailing-edge actuator on drum | |
| 15547 | ALE: timeout moving trailing edge cylinder | |
| 15548 | ALE: timeout moving air cylinder | |
| 15549 | ALE: leading-edge actuator on drum | |
| 15550 | ALE: timeout moving leading edge cylinder | |
| 15551 | ALE: timeout moving roller cylinder | |
| 15552 | ALE: roller on drum | |
| 15556 | ALE: timeout moving load/unload table | |
| 15557 | ALE: load/unload table is in the UP position | |
| 15558 | ALE: load/unload table is in the DOWN position | |
| 15559 | ALE: timeout moving unload table | |
| 15562 | ALE: timeout moving exit flap | |
| 15563 | ALE: cannot move the bay %d tissue compactor, the box lid is in the way | |
| 15564 | ALE: please pull the plate carrier out of bay %d | |
| 15565 | ALE: busy with bay %d, cannot process new message code %04Xh | |
| 15566 | ALE: bay %d safety interlock is open | |
| 15567 | ALE: timeout loading bay %d | |
| 15568 | ALE: bay %d is disabled and turned offline | |
| 15569 | ALE: please close the door on bay %d | |
| 15570 | ALE: please push the carrier in bay %d all the way in | |
| 15571 | ALE: bay %d in use | |
| 15572 | ALE: bay %d is open | |
| 15573 | ALE: bay %d location not initialized in NVS | |
| 15574 | ALE: new bay number out of range | |
| 15575 | ALE: picker inside bay %d, not safe to move | |
| 15576 | ALE: plate box carrier in bay %d is not in the home position | |
| 15577 | ALE: bay %d box lid not open | |
| 15578 | ALE: timeout moving bay %d cassette lid | |
| 15579 | ALE: missing bay %d cassette lid | |
| 15580 | ALE: bay %d cassette lid already on grippers | |
| 15581 | ALE: timeout moving bay %d cassette lid grippers | |
| 15582 | ALE: timeout moving bay %d shutter cylinder | |
| 15583 | ALE: bay %d failed to lock | |
| 15590 | ALE: picker plate-detect microswitch stuck on | |
| 15593 | ALE: timeout homing bay %d paper sweeper | |
| 15594 | ALE: timeout while crushing slip-sheets in bay %d | |
| 15595 | ALE: bay %d paper sweeper is skewed, please move home | |
| 15596 | ALE: bay %d paper sweeper not responding | |
| 15597 | ALE: bay %d paper sweeper blocking action, not home or away | |
| 15598 | ALE: sensors indicate bay %d paper sweeper both home and away | |
| 15599 | ALE: Please move the bay %d paper sweeper home or away | |
| 15600 | ALE: plate in bay %d is not metal | |
| 15601 | ALE: plate in bay %d is metal | |
| 15603 | ALE: plate loaded incorrectly, remove plate from drum | |
| 15604 | ALE: plate too small, remove from load ramp | |
| 15605 | ALE: plate too large or slip sheet attached, remove from load ramp | |
| 15606 | ALE: plate lost after picking, check inside recorder | |
| 15607 | ALE: plate on picker, please remove | |
| 15608 | ALE: no plate on picker or low vac, can't continue | |
| 15609 | ALE: plate on turtle, please remove | |
| 15610 | ALE: no plate on turtle or low vac, can't continue | |
| 15612 | ALE: no plate on load ramp or low vac, can't continue | |
| 15613 | ALE: plate on unload ramp, please remove | |
| 15614 | ALE: no plate on unload ramp or low vac, can't continue | |
| 15615 | ALE: plate stuck on unload ramp | |
| 15616 | ALE: plate on bridge, please remove | |
| 15617 | ALE: no plate on bridge, can't continue | |
| 15618 | ALE: plate on drum, please remove | |
| 15619 | ALE: no plate on drum, can't continue | |
| 15622 | ALE: PICK command already in progress | |
| 15623 | ALE: FETCH command already in progress | |
| 15624 | ALE: LOAD command already in progress | |
| 15625 | ALE: UNLOAD command already in progress | |
| 15626 | ALE: EJECT command already in progress | |
| 15627 | ALE: EJECT command timed out | |
| 15628 | ALE: no plate on push-bar or plate size wrong, can't continue | |
| 15630 | ALE: trailing edge clamp status unknown,\\ possible software or sensor error #%d. | |
| 15631 | ALE: Picker board not responding or wrong version | |
| 15632 | ALE: Turtle board not responding or wrong version | |
| 15633 | ALE: Engine board not responding or wrong version | |
| 15634 | ALE: Unload Ramp board not responding or wrong version | |
| 15636 | ALE: Cassette Bay 1 & 2 board not responding or wrong version | |
| 15637 | ALE: Cassette Bay 3 & 4 board not responding or wrong version | |
| 15638 | ALE: Cassette Bay 5 & 6 board not responding or wrong version | |
| 15640 | ALE: picker Z-axis not in handoff position | |
| 15641 | ALE: turtle W-axis not in position for plate hand-off | |
| 15642 | ALE: picker Z-axis not HOME | |
| 15643 | ALE: picker Z-axis not in position for plate grab | |
| 15644 | ALE: engine_is_installed flag is set to 0! | |
| 15660 | ALE: Waiting for the bay %d door to close | |
| 15661 | ALE: Waiting for the bay %d carrier to get home | |
| 15662 | ALE: Crushing the tissues in bay %d | |
| 15663 | ALE: Closing the cassette lid in bay %d | |
| 15664 | ALE: Opening the cassette lid in bay %d | |
| 15665 | ALE: processor number is invalid, check process[] NVS setting | |
| 15666 | ALE: ejector motor %d stalled, check for plate in bridge | |
| 15667 | ALE: timeout moving ejector %d rollers, check hall sensors | |
| 15668 | ALE: timeout waiting for plate to leave ejector %d | |
| 15669 | ALE: bridge motor %d stalled, check for plate in bridge | |
| 15670 | ALE: timeout moving bridge %d rollers | |
| 15671 | ALE: timeout waiting for plate to leave bridge %d | |
| 15672 | ALE: PROCESS command aborted, check for plate in bridge | |
| 15673 | ALE: please lower processor bridge | |
| 15674 | ALE: please close bridge lid | |
| 15675 | ALE: please close cassette-bay side access door | |
| 15676 | ALE: please close front access door | |
| 15677 | ALE: please close roof access door | |
| 15678 | ALE: picker in bay %d, select RESUME | |
| 15680 | ALE: pick could not complete because table is up | |
| 15681 | ALE: timeout moving tec backbone up or down | |
| 15682 | ALE: attempt to move backbone with tec locked | |
| 15683 | ALE: plate expected to cover lower load sensor | |
| 15684 | ALE: plate expected to be sensed in ejector | |
| 15685 | ALE: attempt to move table while plate in ejector %d | |
| 16005 | IMAGE: update received after load started | |
| 16006 | IMAGE: task received incorrect ID | |
| 16007 | IMAGE: Inactive image task received image update | |
| 16008 | IMAGE: Total mainscan shift less than or equal to zero | |
| 16009 | IMAGE: Total subscan shift less than zero | |
| 16010 | IMAGE: Total mainscan shift too large | |
| 16011 | IMAGE: PLL is not able to track drum motion | |
| 16012 | IMAGE: PLL was not able to maintain drum motion tracking | |
| 16013 | IMAGE: Specified \"around drum\" image size too large | |
| 16018 | IMAGE: exposure too low | |
| 16021 | IMAGE: mainscan length must be a multiple of 16 | |
| 16022 | IMAGE: command received when already suspended | |
| 16023 | IMAGE: plate exposed by open door | |
| 16025 | IMAGE: Stroke must be flat when calibrating scorr | |
| 16026 | IMAGE: Scorr must be initialized in current mode before calibrating | |
| 16027 | IMAGE: TPG not idle after imaging, DPE reset | |
| 16028 | IMAGE: Series plot completed | |
| 16030 | IMAGE: Series strip width is set to zero | |
| 16038 | IMAGE: Total number of retraces: <retraces> | |
| 16050 | IMAGE: DPE orthog slope less than 0, check plate rotation | |
| 16051 | IMAGE: DPE orthog slope larger than max, check plate rotation | |
| 16068 | IMAGE: Unable to initialize plot for mode set to 0 DPI | |
| 17046 | HEAD: multiple edges detected - verify image position | |
| 17501 | HEAD: temperature out of range | |
| 17502 | HEAD: value out of range | |
| 17503 | HEAD: missing laser on parameters | |
| 17504 | HEAD: attempted write blocked | |
| 17505 | HEAD: failure to write to memory | |
| 17506 | HEAD: unsupported message | |
| 17507 | HEAD: message length incorrect | |
| 17508 | HEAD: invalid control message | |
| 17509 | HEAD: operation was aborted | |
| 17532 | HEAD: no more room in mailbox | |
| 17533 | HEAD: ran out of buffers | |
| 17534 | HEAD: all retries failed on chnl 0 | |
| 17535 | HEAD: all retries failed on chnl 1 | |
| 17536 | HEAD: sync lost on chnl 0 | |
| 17537 | HEAD: sync lost on chnl 1 | |
| 17548 | HEAD: CONFIG register incorrect | |
| 17549 | HEAD: flash memory checksum error | |
| 17550 | HEAD: LCA won't init for reprogram | |
| 17551 | HEAD: LCA won't admit being loaded | |
| 17552 | HEAD: SRAM memory check failure | |
| 17596 | HEAD: software error | |
| 17597 | HEAD: LCA config unavailable | |
| 17692 | HEAD: Light level too low for Beam Pointing | |
| 17693 | HEAD: Timeout waiting for LASER OK | |
| 17694 | HEAD: Light valve high voltage fault | |
| 17695 | HEAD: LV Positive 12V fault (bipolar) | |
| 18017 | LASER: Cannot continue, laser is not ready | |
| 19000 | PDB: Air Supply Below Threshold | |
| 21000 | SCSI: SCSI bus reset while imaging | |
| 21001 | SCSI: SCSI parity error while imaging, check plate for artifacts | |
| 21002 | SCSI: SCSI driver error, invalid initiator | |
| 21003 | SCSI: SCSI Driver Error, line <line number> | |
| 21004 | SCSI: SCSI asynchronous transfer requested, line <line number> | |
| 21005 | SCSI: timed out waiting for SCSI complete | |
| 30000 | TPG: memory overflow | |
| 30001 | TPG: too many scans | |
| 30002 | TPG: write to closed scan | |
| 30003 | TPG: write to unopened scan | |
| 30004 | TPG: write to undefined scan | |
| 30005 | TPG: close of closed scan | |
| 30006 | TPG: close of unopen scan | |
| 30007 | TPG: open of NULL scan | |
| 30008 | TPG: Undefined pattern number, use "list pattern" | |
| 30009 | TPG: Call with NULL pattern struct | |
| 30010 | TPG: Pattern write call error | |
| 30011 | TPG: Too many cells in pattern | |
| 30012 | TPG: timed out waiting for stripe to complete | |
| 31002 | LCA: DONE signal stuck low while programming | |
| 31003 | LCA: READY signal stuck low while programming | |
| 31004 | LCA: did not accept programming data | |
| 31006 | LCA: INIT signal stuck low while programming | |
| 31007 | LCA: INIT signal stuck high while programming | |
| 31008 | LCA: Required LCA file is not in firmware | |
| 31009 | LCA: Required LCA master file is not in firmware | |
| 31010 | LCA: Length of LCA diff file does not match master | |
| 32200 | SW: Ink Key buffers out of synch | |
| 32201 | SW: Image shutdown error | |
| 32202 | SW: NCO update timeout | |
| 32203 | SW: Resolution mode not defined | |
| 32301 | SW: Unknown ID code in firmware directory | |
| 32302 | SW: undefined subsystem in NVS list | |
| 32401 | SW: Could not open console interface for serial communications | |
| 32403 | SW: Could not open head interface for serial communications | |
| 32404 | SW: Could not open laser interface for serial communications | |
| 32450 | SW: Out of memory | |
| 32480 | SW: WS data list unexpectedly in use | |
| 32481 | SW: WS command pattern incorrect | |
| 32490 | SW: AL Sched: pick sync error | |
| 32491 | SW: AL Sched: unload sync error | |
| 32492 | SW: AL Sched: load sync error | |
| 32493 | SW: AL Sched: process sync error | |
| 32500 | SW: Unexpected SW failure - general exception | |
| 32600 | SW: executive call failed | |
| 32601 | SW: executive call tsk_create() failed | |
| 32602 | SW: executive call tsk_delete() failed | |
| 32603 | SW: executive call tsk_suspend() failed | |
| 32604 | SW: executive call tsk_resume() failed | |
| 32605 | SW: executive call tsk_set_priority() failed | |
| 32606 | SW: executive call mbx_create() failed | |
| 32607 | SW: executive call mbx_delete() failed | |
| 32608 | SW: executive call mbx_send() failed | |
| 32609 | SW: executive call mbx_receive() failed | |
| 32610 | SW: executive call mbx_flush() failed | |
| 32611 | SW: executive call buf_alloc() failed | |
| 32612 | SW: executive call buf_free() failed | |
| 32613 | SW: executive call tmr_create() failed | |
| 32614 | SW: executive call tmr_delete() failed | |
| 32615 | SW: executive call pip_create() failed | |
| 32616 | SW: executive call pip_delete() failed | |
| 32617 | SW: mbx_send failed, NULL mailbox | |
| 32618 | SW: mbx_send failed, mailbox full | |
| 32700 | SW: all tasks suspended | |
| 32701 | SW: Unexpected message in mailbox <mailbox name>, message code <hex message code> | |
| 32702 | SW: message buffer request failed | |
| 32703 | SW: message buffer release failed | |
| 32704 | SW: string buffer request failed | |
| 32705 | SW: string buffer release failed | |
| 32706 | SW: unexpected case - file:<filename> line:<line number> | |
| 32707 | SW: image command received by active task | |
| 32708 | SW: procedure call has invalid parameters | |
| 32709 | SW: status mask has duplicate flags defined | |
| 32711 | SW: Unexpected message type for this command. type: <hex message type> | |
| 32766 | SW: Non-specific error | |