Home | Contact Us | Submit Troubleshooting Info | Search | Help
Output | Software Solutions | Proofing | Color, Screening and Calibration | Scanning | Digital Photography | Consumables | POS
Home | Contact Us | Submit Troubleshooting Info | Search | Help
Output | Software Solutions | Proofing | Color, Screening and Calibration | Scanning | Digital Photography | Consumables | POS
Autoloader-specific Error Messages | Base Trendsetter VLF Error Messages
See also
This content is generated by scripts that pull information directly from Firmware Engineering's support site. The scripts were last run: 16 Jul 2008 17:30:11
| Number | Error Message | |
|---|---|---|
| 03054 | WSCOMM: Workstation issued flush while job was still active. Aborting job. | |
| 15969 | ALE: Plate size too small, plate mainscan verification disabled | |
| 15970 | ALE: Timeout waiting for the ADC pressure to settle | |
| 15971 | ALE: System air pressure fell below threshold required for PCUPS during operation | |
| 15972 | ALE: System air pressure fell below threshold required for Picker Vacuum during operation | |
| 15973 | ALE: System air pressure fell below threshold required for Table Vacuum during operation | |
| 15974 | ALE: System air pressure fell below threshold required for Slipsheet Vacuum during operation | |
| 15975 | ALE: System air pressure fell below threshold required for Separators during operation | |
| 15976 | ALE: System air pressure fell below threshold required for Picker Deck float during operation | |
| 15977 | ALE: System air pressure fell below threshold required for Slipsheet picker blower during operation | |
| 15978 | ALE: System air pressure fell below threshold required for Table Plate Holder during operation | |
| 15979 | ALE: System air pressure fell below threshold required for Table Cup Blower, during operation | |
| 15980 | ALE: System air pressure fell below threshold required for Table Load vacuum during operation | |
| 15987 | ALE: Pdoor was not fully open when trying to lower/raise table - check pdoor sensors | |
| 15988 | ALE: Table vacuum is above threshold (tvt) before unloading plate. | |
| 15989 | ALE: Vacuum sensor %d offset too large during sensor null calibrating. | |
| 15990 | ALE: Cannot move table because state is unknown, check sensors. | |
| 15991 | ALE: System pressure sensor offset is not calibrated. Run cal pressure | |
| 15992 | ALE: plate may be partly on drum, please remove | |
| 15993 | ALE: Sensor offset too large ,%s | |
| 15994 | ALE: Pressure Sensor Cal invalid, %d; (range: min %d, max %d) | |
| 15995 | ALE: Pressure Sensor Cal invalid | |
| 15996 | ALE: WARNING: Inadequate air supply | |
| 15997 | ALE: Air supply dump valve test failed, Check that bypass valve is closed. | |
| 15998 | ALE: Air supply filter is Blocked, Dumping Air Pressure! Replace filters and restart the machine. | |
| 15999 | ALE: Illegal action while drum is moving, [ACTIONS] | |
| 16066 | IMAGE: Reject plate - unloading from drum | |
| 22200 | ALE2: Forced failure. Type 'ale step fail clear' to continue | |
| 22201 | ALE2: PDB %d satellite board %s cable disconnected | |
| 22202 | ALE2: GENINE %d satellite board %s cable disconnected | |
| 22203 | ALE2: Picker already in use | |
| 22204 | ALE2: Table already in use | |
| 22205 | ALE2: Plate not detected on picker plate-vacuum | |
| 22206 | ALE2: Failed to deactivate Vcup vacuum | |
| 22207 | ALE2: Failed to raise eject finger | |
| 22208 | ALE2: Failed to lower eject finger | |
| 22209 | ALE2: Failed to raise picker p-cup | |
| 22210 | ALE2: Failed to lower picker plate-cup | |
| 22211 | ALE2: X-axis stepper move timed out | |
| 22212 | ALE2: Y-axis stepper move timed out | |
| 22214 | ALE2: Invalid Y-axis clamp command | |
| 22219 | ALE2: Table y-axis failed to move to target position, or over ran target | |
| 22221 | ALE2: Invalid Y-axis clamp command | |
| 22222 | ALE2: Invalid Y-axis clamp command | |
| 22223 | ALE2: Conveyor not installed - cannot activate | |
| 22224 | ALE2: X-axis could not find homeX-axis could not find away | |
| 22225 | ALE2: Y-axis could not find home | |
| 22226 | ALE2: Extended Autoloading Electronics disabled! Manual VLF Trendsetter functional only | |
| 22227 | ALE2: Failed to lock the gate. Make sure is it properly closed | |
| 22228 | ALE2: Failed to unlock the gate | |
| 22229 | ALE2: 24V power supply disabled, check ABORT, gate,conveyor interface plate & drop leaf | |
| 22230 | ALE2: 48V power supply disabled, check ABORT, gate, and panels | |
| 22231 | ALE2: Y-axis cannot move because pdoor isn't closed | |
| 22232 | ALE2: Remove plate from Picker | |
| 22233 | ALE2: Failed to raise slipsheet-picker | |
| 22234 | ALE2: Failed to lower picker slipsheet-cup | |
| 22235 | ALE2: Slipsheet not detected on picker slipsheet vacuum | |
| 22236 | ALE2: Failed to deactivate picker slipsheet vacuum | |
| 22237 | ALE2: Cannot fetch new plate while there is a plate on the drum | |
| 22238 | ALE2: Slipsheet found on table. Remove sheet then hit RESUME | |
| 22239 | ALE2: Slipsheet found on top of plate before lifting. Remove sheet then hit RESUME | |
| 22240 | ALE2: Slipsheet/obstruction above rollers. Bin may be full | |
| 22241 | ALE2: Plate caught on picker, position against yaxis then RESUME | |
| 22242 | ALE2: Cannot move picker over rollers while Slipsheet bin dooror SS safety guard is open | |
| 22243 | ALE2: Slipsheet detected above slipsheet rollers, Resume when ready to remove slipsheet. | |
| 22244 | ALE2: Remove Slipsheets and resume when ready. | |
| 22245 | ALE2: Slipsheet picker vacuum above threshold before picking slipsheet. | |
| 22246 | ALE2: Picker vacuum cup vacuum is above threshold before plate contact. | |
| 22247 | ALE2: Picker unable to grab slipsheet from lower plate after second try. | |
| 22248 | ALE2: Slipsheet found in cassette. Slipsheet handling not installed. Remove sheet then hit RESUME | |
| 22249 | ALE2: ABORT at Autoloader PDB | |
| 22251 | ALE2: Plate detected on picker deck even before picking - check sensor. | |
| 22252 | ALE2: Remove plate from Table | |
| 22253 | ALE2: Slipsheet removal timeout | |
| 22254 | ALE2: Slipsheet detected underneath plate on table. | |
| 22255 | ALE2: WARNING: Service Safety Over Ride is on. Laser and Mechanical hazards exposed. | |
| 22256 | ALE2: NOTE: Slipsheet Roller %s sensor not detected - machine will be slower. | |
| 22257 | ALE2: Plate dropped back in bay, check that plate is properly in bay with slipsheet beneath | |
| 22258 | ALE2: Trendsetter is in Manual mode, but select switch is in Autoloader mode. PLEASE RESET MACHINE | |
| 22259 | ALE2: Trendsetter is in Autoloader mode, but select switch is in Manual mode. PLEASE RESET MACHINE | |
| 22260 | ALE2: No Plate float air detected | |
| 22261 | ALE2: Plate did not arrive in conveyer after ejecting. | |
| 22262 | ALE2: Cannot power or read slipsheet sensor while Slipsheet bin door is open | |
| 22263 | ALE2: I/O failed to write to genine | |
| 22264 | ALE2: Slipsheet sensor (picker) is not functioning correctly | |
| 22265 | ALE2: Picking the LAST plate in current bay | |
| 22266 | ALE2: Bin is Full. %d slipsheets picked | |
| 22267 | ALE2: Picker System pressure sensor is not calibrated. Run cal pressure | |
| 22268 | ALE2: Failed to grab slipsheet from bottom of upper plate. Check nextplate for scratches | |
| 22269 | ALE2: Table not down for fetch or eject | |
| 22270 | ALE2: Pressure sensors need calibrating | |
| 22271 | ALE2: Table slipsheet sensor detected plate when not expected | |
| 22272 | ALE2: | |
| 22273 | ALE2: Pcups failed to lift plate | |
| 22274 | ALE2: CAUTION: Dynamic pressure checking is disabled, faults resulting from air pressure drop will not be reported | |
| 22275 | ALE2: WARNING: Slipsheet sensor reading is out of normal range of slipsheet and empty cassette | |
| 22276 | ALE2: WARNING: Slipsheet roller sensors fault, machine will be slower | |
| 22277 | ALE2: NOTE: Slipsheet sensors did not detect slipsheet beteen plates. Check media x sst | |
| 22278 | ALE2: 24V on genine %d is low | |
| 22279 | ALE2: 48V on genine %d is low | |
| 22280 | ALE2: Autoloader Abort cleared | |
| 22281 | ALE2: WARNING: Plate Transfer to Vcups required wedgemaster to contact plates. Check Next plate for scratches | |
| 22282 | ALE2: Picker lost grip of plate during operation (pvac below threshold) | |
| 22283 | ALE2: Plate lost during Fetch | |
| 22284 | ALE2: System pressure out of tollerance. Please run cal pressure | |
| 22285 | ALE2: Unable to calibrate media slipsheet threshold | |
| 22286 | ALE2: Unable to calibrate media slipsheet threshold | |
| 22287 | ALE2: Unable to calibrate Picker vacuum threshold | |
| 22289 | ALE2: Slipsheet bin door or SS safety guard is open | |
| 22290 | ALE2: Air supply filter has been permanently damaged and MUST be replace, even if this message does not re-occur | |
| 22291 | ALE2: Air supply filter is missing. Please install all filters asap. | |
| 22292 | ALE2: Air supply filter differential analog reading is unstable, Genine 0 | |
| 22293 | ALE2: Air supply filter is dirty | |
| 22294 | ALE2: L Conveyor not ready to accept plate being ejected from unload | |
| 22295 | ALE2: GENINE %d, %s | |
| 22296 | ALE2: Slipsheet bin is getting full. %d Slipsheets picked | |
| 22297 | ALE2: Picker Arm is not down, can't move picker. | |
| 22298 | ALE2: Slipsheet roller %s timeout | |
| 22299 | ALE2: Remove Slipsheet abandoned in bay. | |
| 22300 | ALE2: Cassette already in use | |
| 22301 | ALE2: Cassette %u is not loaded, RESUME to continue anyway | |
| 22302 | ALE2: "Cassette %u is already loaded, RESUME to unload cassette" | |
| 22303 | ALE2: "Cassette cart not is position for loading, replace cart then select RESUME" | |
| 22304 | ALE2: "Timeout moving cassette door" | |
| 22305 | ALE2: "Invalid number of cassettes configured. Check NVS \"val cassettes_installed\" | |
| 22307 | ALE2: "Invalid cassette number (%u) specified" | |
| 22308 | ALE2: "Cassette Picker-Door did not close (obstructed)" | |
| 22309 | ALE2: "Cassette sensors are disabled. Select RESUME once cart is in position for loading." | |
| 22310 | ALE2: "Cassette cart has not been removed for plate loading. Continue plate loading?" | |
| 22311 | ALE2: "Cassette command failed" | |
| 22312 | ALE2: "Invalid cassette %u specified in command" | |
| 22314 | ALE2: "MCU plate door is open. Not safe for MCU movement" ) | |
| 22315 | ALE2: "MCU position is invalid" | |
| 22316 | ALE2: "MCU safety-loop is open. Check all MCU doors and chariot" | |
| 22317 | ALE2: "Unsafe for command. MCU motor is moving" | |
| 22318 | ALE2: "Chariot has a cassette and cannot be parked" | |
| 22319 | ALE2: "Chariot already has a cassette (cannot unload another cassette)" | |
| 22320 | ALE2: "Another cassette is already loaded in MCU position %u" | |
| 22321 | ALE2: "No cassette is loaded in MCU position %u" | |
| 22322 | ALE2: "MCU motor did not stop on time" | |
| 22323 | ALE2: "Please move the MCU plate cassette chariot to parked position" | |
| 22324 | ALE2: "Please move the MCU plate cassette chariot fully inside the unit" | |
| 22325 | ALE2: "Please move the MCU plate cassette chariot fully out" | |
| 22326 | ALE2: "Please wait, the MCU is moving to the selected cassette" | |
| 22327 | ALE2: "Failed to activate the MCU Motor" | |
| 22328 | ALE2: "WARNING: MCU sensors disabled. Continuing to run may cause damage to the machine" | |
| 22329 | ALE2: "MCU not in a safe state for motor movement" | |
| 22350 | ALE2: "Conveyor already in use" | |
| 22351 | ALE2: "GENINE4 satellite board %s cable disconnected | |
| 22352 | ALE2: "Timeout moving conveyor rotator" | |
| 22353 | ALE2: "Conveyor exit is blocked" | |
| 22354 | ALE2: "Timeout waiting for plate to enter conveyor" | |
| 22355 | ALE2: "Timeout jogging conveyor belts" | |
| 22356 | ALE2: "Timeout stopping conveyor belts" | |
| 22357 | ALE2: "Invalid conveyor type configured. Check NVS val conveyor_installed | |
| 22358 | ALE2: "Conveyor stopped. Make sure the guard rail gate & drop leaf are closed" | |
| 22359 | ALE2: "Conveyor X-axis stepper move timed out" | |
| 22360 | ALE2: "Conveyor Y-axis stepper move timed out" | |
| 22361 | ALE2: "Conveyor X-axis could not find home" | |
| 22362 | ALE2: "Conveyor Y-axis could not find home" | |
| 22363 | ALE2: "Timeout raising/lowering l-conveyor table surface" | |
| 22364 | ALE2: "Plate not detected on conveyer rotator plate-vacuum" | |
| 22365 | ALE2: "Failed to deactivate Vcup vacuum" | |
| 22366 | ALE2: "Remove plate from Conveyor" | |
| 22367 | ALE2: "Plate did not reach conveyor exit" | |
| 22368 | ALE2: "Plate did not leave conveyor exit" | |
| 22369 | ALE2: "Timeout waiting for plate to enter fully onto conveyor" | |
| 22370 | ALE2: "Conveyor Entrance sensor is blocked" | |
| 22372 | ALE2: "Processor %s is Not Ready" | |
| 22373 | ALE2: "Processor is Busy or Not Ready" | |
| 22374 | ALE2: "Time out waiting for processor %s Busy" | |
| 22375 | ALE2: "Processor %s is indicating a Fault" | |
| 22401 | ALE2: WARNING: Some nvs have been temporarily disabled, these will expirein %lu hours,\n\ which may bring the machine down. | |
| 22406 | ALE2: Failed to grab slipsheet, check NEXT plate for scratches | |
| 23000 | SCON: illegal message buffer specified | |
| 23001 | SCON: illegal message data size specified | |
| 23101 | SCON: SIF general failure %d | |
| 23102 | SCON: Received an SCON NAK reply for register %03Xh at %02Xh data = %Xh | |
| 23103 | SCON: SCON transmit timed out | |
| 23104 | SCON: SCON timeout waiting for read ACK from register %03Xh at %02Xh | |
| 23105 | SCON: SCON timeout waiting for write ACK from register %03Xh at %02Xh | |
| 23106 | SCON: No free CAN transmit buffers available | |
| 23107 | SCON: SCON Datalink timeout | |
| 23201 | SCON: Invalid board type specified: %02X | |
| 23202 | SCON: Invalid register specified: %03X | |
| 23203 | SCON: SAT I/O Node %02X does not exist | |
| 23204 | SCON: Failed to establish SCON communications with %s | |
| 23205 | SCON: Reset reported on %s board | |
| 23206 | SCON: Unregistered board %02X detected | |
| 23300 | SCON: CANbus Satellite board %02X not accepting commands | |
| 23301 | SCON: Invalid command | |
| 23302 | SCON: Cannot execute command, Stepper Motor %u is moving | |
| 23303 | SCON: Invalid motor number %u specified | |
| 23304 | SCON: Stepper Motor %u is already reserved | |
| 23305 | SCON: Invalid Trajectory Queue Address (%u) | |
| 23306 | SCON: Invalid Parameter | |
| 23307 | SCON: Invalid Velocity Value | |
| 23308 | SCON: Invalid Acceleration Value | |
| 23309 | SCON: Invalid Step Rate | |
| 23310 | SCON: Invalid Current Level | |
| 23311 | SCON: Invalid Motor Direction | |
| 23312 | SCON: Motor is in invalid mode for requested command | |
| 23313 | SCON: Stepper output gain specified is too high | |
| 23314 | SCON: Stepper Motor %u hardware error | |
| 23315 | SCON: Stepper Motor %u is not initialized | |
| 23316 | SCON: Invalid stepper \"%s\" specified | |
| 23317 | SCON: Stepper Motor %u 48V safe low | |
| 23318 | SCON: Stepper Motor %u alternate sensor cable not detected | |
| 23319 | SCON: Stepper Motor %u home/away cable not detected | |
| 23320 | SCON: Stepper Motor %u power cable not detected | |
| 23321 | SCON: Stepper Motor %u data cable not detected | |
| 23322 | SCON: Stepper Motor %u driver fault detected | |
| 23323 | SCON: Stepper Motor %u cable not detected | |
| 23324 | SCON: Stepper Motor %u brake override detected | |
| 23325 | SCON: Stepper Motor %u driver over temperature fault detected | |
| 23326 | SCON: Stepper Motor %u driver over current fault detected | |
| 23327 | SCON: Stepper Motor %u driver under voltage fault detected | |
This content is generated by scripts that pull information directly from Firmware Engineering's support site. The scripts were last run: 16 Jul 2008 17:30:08
| Number | Error Message | |
|---|---|---|
| 00000 | MISC: | |
| 00001 | MISC: Reserved | |
| 00002 | MISC: Reserved | |
| 00003 | MISC: Reserved | |
| 00004 | MISC: Reserved | |
| 00005 | MISC: Reserved | |
| 00006 | MISC: Reserved | |
| 00007 | MISC: Reserved | |
| 00020 | MISC: Specified test is not defined | |
| 00021 | MISC: Workstation communications lost | |
| 00030 | MISC: Requested command is not defined | |
| 00100 | MISC: MPE Code checksum is faulty | |
| 00101 | MISC: LCA module checksum is faulty | |
| 00102 | MISC: LCA module incompatable format | |
| 00103 | MISC: Module not found in version list | |
| 00104 | MISC: Firmware module checksum is faulty | |
| 00105 | MISC: Error opening firmware module | |
| 00106 | MISC: Invalid or unneeded code bundled with firmware | |
| 00107 | MISC: Missing required code in the firmware bundle | |
| 00108 | MISC: Product version not found in version list | |
| 00109 | MISC: Invalid version of overwriting pattern | |
| 00200 | MISC: Code bank selected for loadingis current code bank | |
| 00201 | MISC: Flash memory program failed | |
| 00202 | MISC: Address <hex address> out of memory bank range | |
| 00203 | MISC: Unsupported memory type detected | |
| 00204 | MISC: Flash memory erase failed | |
| 00500 | MISC: Temperature log: Engine = <Celcius x 10> Leadscrew = <Celcius x 10> | |
| 00501 | MISC: Password not set! | |
| 00502 | MISC: NVS modified and saved, but not backed up! | |
| 00511 | MISC: Dongle not responding | |
| 00512 | MISC: Config: %s %s owner %s | |
| 01000 | RESET: cause unknown | |
| 01001 | RESET: induced by test submodule | |
| 01002 | RESET: induced by RESET opcode, possible warm reset requested at monitor | |
| 01004 | RESET: induced by loss of clock | |
| 01016 | RESET: induced by halt monitor | |
| 01032 | RESET: induced by software watchdog, possible cold reset requested at monitor | |
| 02000 | NVS: checksum error in <NVS subsystem> calibration block | |
| 02040 | NVS: checksum error in <NVS subsystem> configuration block | |
| 02080 | NVS: checksum error in mode <number> table | |
| 02200 | NVS: low battery in NVS detected | |
| 02201 | NVS: NVS automatically upgraded to version 2 | |
| 02202 | NVS: subscan size nvs config parameter is invalid | |
| 03000 | WSCOMM: All faults cleared | |
| 03001 | WSCOMM: Invalid command letter | |
| 03002 | WSCOMM: Parameter syntax error | |
| 03003 | WSCOMM: Defined WS command is currently unsupported | |
| 03004 | WSCOMM: Character pacing timeout, WS transmitting too slowly | |
| 03005 | WSCOMM: too many characters in command string | |
| 03006 | WSCOMM: Could not open serial communications interface for workstation | |
| 03007 | WSCOMM: Resume or clear received when not suspended | |
| 03008 | WSCOMM: Command received for idle image ID | |
| 03009 | WSCOMM: Specified image ID is already active | |
| 03010 | WSCOMM: Maximum active image commands surpassed | |
| 03011 | WSCOMM: Resolution specified is not available | |
| 03012 | WSCOMM: Already aborting | |
| 03014 | WSCOMM: Abort received when no command active | |
| 03015 | WSCOMM: Already imaging | |
| 03016 | WSCOMM: Recorder is flushing, can't accept new commands | |
| 03017 | WSCOMM: Door is open | |
| 03018 | WSCOMM: Door is closed | |
| 03019 | WSCOMM: ABORT switch on | |
| 03020 | WSCOMM: ABORT switch off | |
| 03021 | WSCOMM: Operation aborted at recorder - check that abort switch is released | |
| 03022 | WSCOMM: Operation aborted by workstation | |
| 03023 | WSCOMM: ABORT complete | |
| 03024 | WSCOMM: Abort request not heeded within timeout, possible hung subsystem | |
| 03025 | WSCOMM: Task(s) <task codes> did not finish initializing on time | |
| 03026 | WSCOMM: Operation preempted | |
| 03027 | WSCOMM: Cassette bay door open | |
| 03028 | WSCOMM: Cassette bay door closed | |
| 03047 | WSCOMM: Resolution does not exist | |
| 03048 | WSCOMM: Image too wide for plate | |
| 03055 | WSCOMM: Workstation software error - Invalid packet number | |
| 03056 | WSCOMM: Workstation software error - Invalid total packets number | |
| 03057 | WSCOMM: Workstation software error - Out of sequence packet received | |
| 03058 | WSCOMM: Workstation software error - Invalid packet length | |
| 03059 | WSCOMM: Workstation software error - Invalid Media Imaging Mode ID (MIMID) | |
| 03060 | WSCOMM: Packet fails CRC check | |
| 03061 | WSCOMM: Total packet data exceeding firmware buffer capacity | |
| 04001 | MSG: Command parameter error | |
| 04002 | MSG: Parameter is out of range | |
| 04003 | MSG: Defined command is currently unsupported | |
| 04004 | MSG: Requested test pattern not defined | |
| 04005 | MSG: <subsystem> is already reserved | |
| 04006 | MSG: Reserved message in message pool | |
| 04007 | MSG: Task releasing message owned by another task | |
| 04008 | MSG: Task releasing unreserved message | |
| 04009 | MSG: Task sending message owned by another task | |
| 04010 | MSG: Task sending unreserved message | |
| 04011 | MSG: Task received message that was not sent | |
| 04012 | MSG: Reserved string in string pool | |
| 04013 | MSG: Task releasing unreserved string | |
| 04014 | MSG: Task releasing string owned by another task | |
| 04015 | MSG: Task reserving released string | |
| 04016 | MSG: <task name> timed out while waiting for command <hex command code> | |
| 04017 | MSG: <task name> received an invalid command (command = <hex command code>) | |
| 04018 | MSG: Wrong number of parameters | |
| 04019 | MSG: Inactive list sent | |
| 04020 | MSG: Unexpected list type sent | |
| 04021 | MSG: Invalid list entry number sent - Possible version incompatabilities | |
| 04022 | MSG: Plot mode not specified before plot parameters | |
| 04024 | MSG: Task received msg with unexpected id (code = %X) | |
| 04028 | MSG: suspended - waiting for Resume or Clear | |
| 04029 | MSG: plate thickness too large | |
| 04030 | MSG: one or both plate dimensions too large | |
| 04031 | MSG: media type out of range | |
| 04032 | MSG: one or both plate dimensions too small | |
| 04034 | MSG: media %d not supported | |
| 06000 | DRUM: Timeout on drum operation | |
| 06001 | DRUM: Illegal command state machine state | |
| 06002 | DRUM: Timeout waiting for drum move | |
| 06003 | DRUM: Received invalid command | |
| 06004 | DRUM: drum not initialized - can't execute that command | |
| 06005 | DRUM: Unexpected status returned from function | |
| 06006 | DRUM: Timeout during active braking | |
| 06007 | DRUM: Timeout on velocity settling | |
| 06008 | DRUM: Timeout on velocity acceleration | |
| 06009 | DRUM: Sample interrupt failure | |
| 06011 | DRUM: Servo amp fault | |
| 06012 | DRUM: Cable from motherboard to drum servo amp not detected | |
| 06013 | DRUM: Index not detected | |
| 06014 | DRUM: Extra Tach A pulse detected | |
| 06015 | DRUM: Missing Tach A pulse | |
| 06016 | DRUM: Extra Tach B pulse detected | |
| 06017 | DRUM: Missing Tach B pulse | |
| 06018 | DRUM: Drive direction incorrect - check motor wiring | |
| 06019 | DRUM: Tach encoder cable not detected | |
| 06020 | DRUM: Aborted | |
| 06021 | DRUM: Timeout on hold | |
| 06022 | DRUM: Motor current exceeded limit | |
| 06023 | DRUM: Velocity error - drum rotation blocked or PID gain settings wrong | |
| 06024 | DRUM: Position error is greater than 1000 ticks | |
| 06025 | DRUM: Hall velocity error - drum rotation blocked or PID gain settings wrong | |
| 06026 | DRUM: Timeout waiting for TPU hall sensor PW measurement | |
| 06027 | DRUM: Plate not loaded correctly on drum, obstruction detected below LEC actuator | |
| 06028 | DRUM: ALE actuators on drum | |
| 06029 | DRUM: Hall mode overspeed error - possible TPU failure | |
| 06030 | DRUM: Drum hall velocity does not match encoder velocity to within tolerance. | |
| 06031 | DRUM: Drum is spinning. | |
| 06033 | DRUM: Index detected prematurely - clean encoder disc or re-align encoder | |
| 06034 | DRUM: Drum won't settle with zero torque applied - requires drum cal | |
| 06036 | DRUM: Drum Position error during Velocity mode, (check acceleration setting) | |
| 06037 | DRUM: Drum velocity greater than xx rpm in Position mode, possible runaway | |
| 06038 | DRUM: LCA tick counter annomaly, premature index or spurious counter reset | |
| 06039 | DRUM: Drum Position error during Velocity mode, (extra index possible cause, check monitor values) | |
| 06040 | DRUM: Encoder counted extra ticks | |
| 06041 | DRUM: Index occurred at xx, more than 3 ticks before normal ticks per rotation | |
| 06042 | DRUM: Hall velocity error - more than 20 percent during drum init. | |
| 07000 | CARRIAGE: Limit switches reporting carriage is both HOME and AWAY | |
| 07001 | CARRIAGE: stuck in HOME position | |
| 07002 | CARRIAGE: stuck in AWAY position | |
| 07003 | CARRIAGE: unexpectedly arrived at HOME position | |
| 07004 | CARRIAGE: unexpectedly arrived at AWAY position - image size may have been too large | |
| 07005 | CARRIAGE: operation timed out | |
| 07006 | CARRIAGE: timed out while waiting for LCA position | |
| 07007 | CARRIAGE: position register not accurate | |
| 07008 | CARRIAGE: LCA's not configured at startup | |
| 07009 | CARRIAGE: ALE not taken out of reset | |
| 07010 | CARRIAGE: Unexpected error: 0x%x | |
| 07011 | CARRIAGE: could not find edge of platecheck that plate size is entered correctly | |
| 07012 | CARRIAGE: did not reach target speed | |
| 07013 | CARRIAGE: step synth position register reserved | |
| 07015 | CARRIAGE: Head Stage is at it's away position, unsafe to move carriage | |
| 07016 | CARRIAGE: ALE board timed out during carriage position read | |
| 07017 | CARRIAGE: Carriage state error. Current state: <description>, jog_count = <n> JOG = <number> PLOT = <number> | |
| 07018 | CARRIAGE: Carriage illegal dest. Current %lu, Dest %lu Stop Dist %lu | |
| 07019 | CARRIAGE: Specified Speed exceeds maximum of %lu | |
| 08000 | PROC: Processor not present or turned off | |
| 08001 | PROC: Processor is not ready | |
| 08002 | PROC: Processor fault requires immediate attn. | |
| 08003 | PROC: Processor warning will need attention | |
| 08004 | PROC: Processor type unknown | |
| 08005 | PROC: Illegal processor number used | |
| 10012 | HARDWARE: Carriage limit switch | |
| 10019 | HARDWARE: ALE is not plugged in | |
| 10020 | HARDWARE: DPE is not plugged in | |
| 10022 | HARDWARE: MPE LCA's not configured at startup | |
| 10023 | HARDWARE: DPE will not initialize, may be stuck in reset | |
| 10025 | HARDWARE: DPE LCA's not configured at startup | |
| 10026 | HARDWARE: Incorrect DPE version installed | |
| 10050 | HARDWARE: RAM DAC Incrementing Address Test fail - Address = <fault address>, Write data = <hex data>, Readdata = <hex data> | |
| 10051 | HARDWARE: DPE failure - dpath control write = <hex data>, read = <hex data> | |
| 10060 | HARDWARE: External Debris Blower Filters Not Present | |
| 10061 | HARDWARE: External Debris Blower Filters Full | |
| 10062 | HARDWARE: External Debris Blower Filters Almost Full (Vacuum Level %d is below %d) | |
| 10063 | HARDWARE: External Debris Blower System Blocked (Vacuum Level %d is above %d) | |
| 10064 | HARDWARE: External Debris Blower Not Connected or Filters Full (Vacuum Level %d is below %d) | |
| 10065 | HARDWARE: DBlower Filter Fault. | |
| 11000 | CABLE: HA-BP cbl, Carriage Home/Away | |
| 11002 | CABLE: EH-BP: Exposure Head - Backplane | |
| 11003 | CABLE: TE-BP: Tach Encoder - Backplane | |
| 11004 | CABLE: MD-BP: Drum Motor - Backplane | |
| 11504 | CABLE: SPR-BP | |
| 12000 | POWER: ALE +12V | |
| 12001 | POWER: ALE -12V | |
| 12002 | POWER: Carriage power | |
| 12006 | POWER: Carriage Amp Fault | |
| 12007 | POWER: Exposure Head power | |
| 12008 | POWER: Drum Amp Fault | |
| 12801 | POWER: ALE -2V | |
| 13000 | EHBOOT: internal message timeout | |
| 13001 | EHBOOT: datalink terminated the program sequence prematurely | |
| 13002 | EHBOOT: format error detected during data transfer | |
| 13003 | EHBOOT: sumcheck error detected during data transfer | |
| 13004 | EHBOOT: datalink programming sequence taking too long | |
| 13005 | EHBOOT: LOADER echo mismatch during bootstrap sequence | |
| 13006 | EHBOOT: LOADER not echoed during bootstrap sequence | |
| 13007 | EHBOOT: no break detected after forcing head into bootstrap mode | |
| 13008 | EHBOOT: cannot perform requested operation, no LOADER present | |
| 13009 | EHBOOT: LOADER prompt for next primitive did not arrive | |
| 13010 | EHBOOT: communications error | |
| 13011 | EHBOOT: failed to program location <hex data> with data <hex data> | |
| 13012 | EHBOOT: failed to erase device, stopped at location <hex data> | |
| 13013 | EHBOOT: failed to respond to programming command | |
| 13014 | EHBOOT: Timeout on byte <byte #> while waiting for exposure head to complete response string | |
| 13015 | EHBOOT: ENQ expected and not received | |
| 13016 | EHBOOT: ACK expected and not received | |
| 13017 | EHBOOT: incorrect response length | |
| 13018 | EHBOOT: incorrect version length | |
| 13019 | EHBOOT: incorrect version response in byte <byte #> | |
| 13020 | EHBOOT: incorrect response address | |
| 13021 | EHBOOT: incorrect response data | |
| 14000 | SAT: Satellite error cleared | |
| 14001 | SAT: SPI system not initialized | |
| 14002 | SAT: Unknown Satellite Output Register: <hex number> | |
| 14003 | SAT: Satellite SW corrupted Buffer | |
| 14004 | SAT: Buffer Restore error during Output Command | |
| 14050 | SAT: QSPI error during configuration | |
| 14051 | SAT: Timeout during SPI enable | |
| 14052 | SAT: Timeout during QSPI disable | |
| 14053 | SAT: Timeout during SPI execution | |
| 14054 | SAT: SPI Mode Fault error | |
| 14055 | SAT: QSPI Update Watchdog timeout | |
| 14056 | SAT: <Satellite Board> Error: <Output Name> | |
| 14057 | SAT: Error Detection Error: Address <address>, Bit = <bit number> | |
| 14100 | SAT: Temperature Filter Error: Out of range | |
| 14101 | SAT: LUE Analog testpoint exceeded allowed maximum | |
| 14102 | SAT: LUE Analog testpoint exceeded allowed minimum | |
| 14103 | SAT: Engine Frame temperature out of range | |
| 14104 | SAT: Engine Leadscrew temperature out of range | |
| 14105 | SAT: Spare sensor 0 temperature out of range | |
| 14106 | SAT: Spare sensor 1 temperature out of range | |
| 14107 | SAT: Timeout waiting for conveyor roller speed to update | |
| 14108 | SAT: Timeout waiting for conveyor belt speed to update | |
| 14150 | SAT: Cassette Bay <bay number> invalid, autoloader currently configured for <max> bays | |
| 14151 | SAT: Cassette Bay <bay number> Error: <device> | |
| 14200 | SAT: PPE Analog testpoint exceeded allowed maximum | |
| 14201 | SAT: PPE Analog testpoint exceeded allowed minimum | |
| 14203 | SAT: Software error: invalid image task state %d in sat_update_lamps() | |
| 15062 | ALE: plate loaded incorrectly, remove plate from drum | |
| 15071 | ALE: remove plate from drum | |
| 15072 | ALE: remove plate partially on drum | |
| 15074 | ALE: trailing edge clamps failed to unlock | |
| 15075 | ALE: trailing edge clamps failed to lock | |
| 15076 | ALE: trailing edge clamps not on actuator | |
| 15077 | ALE: trailing edge clamps already on actuator, possible sensor or software error. | |
| 15078 | ALE: no plate on drum | |
| 15079 | ALE: timeout moving leading edge cylinder | |
| 15080 | ALE: timeout moving trailing edge cylinder | |
| 15082 | ALE: timeout moving roller cylinder | |
| 15503 | ALE: ALE board still in reset | |
| 15504 | ALE: ALE board not responding | |
| 15506 | ALE: command already in progress | |
| 15507 | ALE: Autoloader operation aborted | |
| 15508 | ALE: Autoloader not initialized | |
| 15509 | ALE: System air pressure too low! | |
| 15510 | ALE: Processor channel %d is invalid | |
| 15511 | ALE: not implemented yet | |
| 15520 | ALE: %s %d communication error | |
| 15521 | ALE: %s %d is busy | |
| 15522 | ALE: %s %d initialization error | |
| 15523 | ALE: %s %d not initialized | |
| 15524 | ALE: %s %d SW error: invalid PARAMETER | |
| 15525 | ALE: %s %d aborted while moving | |
| 15526 | ALE: %s %d SW error: invalid STATE | |
| 15528 | ALE: %s %d timed out while aborting | |
| 15531 | ALE: %s %d HOME limit switch is active | |
| 15532 | ALE: %s %d AWAY limit switch is active | |
| 15533 | ALE: %s %d timed out while homing | |
| 15534 | ALE: %s %d timed out while moving | |
| 15535 | ALE: please close access door | |
| 15539 | ALE: engine mount lock cylinders didn't move | |
| 15540 | ALE: move clamps to park position, then select RESUME | |
| 15542 | ALE: trailing edge clamps failed to unlock | |
| 15543 | ALE: trailing edge clamps failed to lock | |
| 15544 | ALE: trailing edge clamps not on actuator | |
| 15545 | ALE: trailing edge clamps on actuator | |
| 15546 | ALE: trailing-edge actuator on drum | |
| 15547 | ALE: timeout moving trailing edge cylinder | |
| 15548 | ALE: timeout moving air cylinder | |
| 15549 | ALE: leading-edge actuator on drum | |
| 15550 | ALE: timeout moving leading edge cylinder | |
| 15551 | ALE: timeout moving roller cylinder | |
| 15552 | ALE: roller on drum | |
| 15556 | ALE: timeout moving load/unload table | |
| 15557 | ALE: load/unload table is in the UP position | |
| 15558 | ALE: load/unload table is in the DOWN position | |
| 15559 | ALE: timeout moving unload table | |
| 15562 | ALE: timeout moving exit flap | |
| 15563 | ALE: cannot move the bay %d tissue compactor, the box lid is in the way | |
| 15564 | ALE: please pull the plate carrier out of bay %d | |
| 15565 | ALE: busy with bay %d, cannot process new message code %04Xh | |
| 15566 | ALE: bay %d safety interlock is open | |
| 15567 | ALE: timeout loading bay %d | |
| 15568 | ALE: bay %d is disabled and turned offline | |
| 15569 | ALE: please close the door on bay %d | |
| 15570 | ALE: please push the carrier in bay %d all the way in | |
| 15571 | ALE: bay %d in use | |
| 15572 | ALE: bay %d is open | |
| 15573 | ALE: bay %d location not initialized in NVS | |
| 15574 | ALE: new bay number out of range | |
| 15575 | ALE: picker inside bay %d, not safe to move | |
| 15576 | ALE: plate box carrier in bay %d is not in the home position | |
| 15577 | ALE: bay %d box lid not open | |
| 15578 | ALE: timeout moving bay %d cassette lid | |
| 15579 | ALE: missing bay %d cassette lid | |
| 15580 | ALE: bay %d cassette lid already on grippers | |
| 15581 | ALE: timeout moving bay %d cassette lid grippers | |
| 15582 | ALE: timeout moving bay %d shutter cylinder | |
| 15583 | ALE: bay %d failed to lock | |
| 15590 | ALE: picker plate-detect microswitch stuck on | |
| 15593 | ALE: timeout homing bay %d paper sweeper | |
| 15594 | ALE: timeout while crushing slip-sheets in bay %d | |
| 15595 | ALE: bay %d paper sweeper is skewed, please move home | |
| 15596 | ALE: bay %d paper sweeper not responding | |
| 15597 | ALE: bay %d paper sweeper blocking action, not home or away | |
| 15598 | ALE: sensors indicate bay %d paper sweeper both home and away | |
| 15599 | ALE: Please move the bay %d paper sweeper home or away | |
| 15600 | ALE: plate in bay %d is not metal | |
| 15601 | ALE: plate in bay %d is metal | |
| 15603 | ALE: plate loaded incorrectly, remove plate from drum | |
| 15604 | ALE: plate too small, remove from load ramp | |
| 15605 | ALE: plate too large or slip sheet attached, remove from load ramp | |
| 15606 | ALE: plate lost after picking, check inside recorder | |
| 15607 | ALE: plate on picker, please remove | |
| 15608 | ALE: no plate on picker or low vac, can't continue | |
| 15609 | ALE: plate on turtle, please remove | |
| 15610 | ALE: no plate on turtle or low vac, can't continue | |
| 15612 | ALE: no plate on load ramp or low vac, can't continue | |
| 15613 | ALE: plate on unload ramp, please remove | |
| 15614 | ALE: no plate on unload ramp or low vac, can't continue | |
| 15615 | ALE: plate stuck on unload ramp | |
| 15616 | ALE: plate on bridge, please remove | |
| 15617 | ALE: no plate on bridge, can't continue | |
| 15618 | ALE: plate on drum, please remove | |
| 15619 | ALE: no plate on drum, can't continue | |
| 15622 | ALE: PICK command already in progress | |
| 15623 | ALE: FETCH command already in progress | |
| 15624 | ALE: LOAD command already in progress | |
| 15625 | ALE: UNLOAD command already in progress | |
| 15626 | ALE: EJECT command already in progress | |
| 15627 | ALE: EJECT command timed out | |
| 15628 | ALE: no plate on push-bar or plate size wrong, can't continue | |
| 15630 | ALE: trailing edge clamp status unknown,\\ possible software or sensor error #%d. | |
| 15631 | ALE: Picker board not responding or wrong version | |
| 15632 | ALE: Turtle board not responding or wrong version | |
| 15633 | ALE: Engine board not responding or wrong version | |
| 15634 | ALE: Unload Ramp board not responding or wrong version | |
| 15636 | ALE: Cassette Bay 1 & 2 board not responding or wrong version | |
| 15637 | ALE: Cassette Bay 3 & 4 board not responding or wrong version | |
| 15638 | ALE: Cassette Bay 5 & 6 board not responding or wrong version | |
| 15640 | ALE: picker Z-axis not in handoff position | |
| 15641 | ALE: turtle W-axis not in position for plate hand-off | |
| 15642 | ALE: picker Z-axis not HOME | |
| 15643 | ALE: picker Z-axis not in position for plate grab | |
| 15644 | ALE: engine_is_installed flag is set to 0! | |
| 15660 | ALE: Waiting for the bay %d door to close | |
| 15661 | ALE: Waiting for the bay %d carrier to get home | |
| 15662 | ALE: Crushing the tissues in bay %d | |
| 15663 | ALE: Closing the cassette lid in bay %d | |
| 15664 | ALE: Opening the cassette lid in bay %d | |
| 15665 | ALE: processor number is invalid, check process[] NVS setting | |
| 15666 | ALE: ejector motor %d stalled, check for plate in bridge | |
| 15667 | ALE: timeout moving ejector %d rollers, check hall sensors | |
| 15668 | ALE: timeout waiting for plate to leave ejector %d | |
| 15669 | ALE: bridge motor %d stalled, check for plate in bridge | |
| 15670 | ALE: timeout moving bridge %d rollers | |
| 15671 | ALE: timeout waiting for plate to leave bridge %d | |
| 15672 | ALE: PROCESS command aborted, check for plate in bridge | |
| 15673 | ALE: please lower processor bridge | |
| 15674 | ALE: please close bridge lid | |
| 15675 | ALE: please close cassette-bay side access door | |
| 15676 | ALE: please close front access door | |
| 15677 | ALE: please close roof access door | |
| 15678 | ALE: picker in bay %d, select RESUME | |
| 15680 | ALE: pick could not complete because table is up | |
| 15681 | ALE: timeout moving tec backbone up or down | |
| 15682 | ALE: attempt to move backbone with tec locked | |
| 15683 | ALE: plate expected to cover lower load sensor | |
| 15684 | ALE: plate expected to be sensed in ejector | |
| 15685 | ALE: attempt to move table while plate in ejector %d | |
| 16005 | IMAGE: update received after load started | |
| 16006 | IMAGE: task received incorrect ID | |
| 16007 | IMAGE: Inactive image task received image update | |
| 16008 | IMAGE: Total mainscan shift less than or equal to zero | |
| 16009 | IMAGE: Total subscan shift less than zero | |
| 16010 | IMAGE: Total mainscan shift too large | |
| 16011 | IMAGE: PLL is not able to track drum motion | |
| 16012 | IMAGE: PLL was not able to maintain drum motion tracking | |
| 16013 | IMAGE: Specified \"around drum\" image size too large | |
| 16018 | IMAGE: exposure too low | |
| 16021 | IMAGE: mainscan length must be a multiple of 16 | |
| 16022 | IMAGE: command received when already suspended | |
| 16023 | IMAGE: plate exposed by open door | |
| 16025 | IMAGE: Stroke must be flat when calibrating scorr | |
| 16026 | IMAGE: Scorr must be initialized in current mode before calibrating | |
| 16027 | IMAGE: TPG not idle after imaging, DPE reset | |
| 16028 | IMAGE: Series plot completed | |
| 16030 | IMAGE: Series strip width is set to zero | |
| 16038 | IMAGE: Total number of retraces: <retraces> | |
| 16050 | IMAGE: DPE orthog slope less than 0, check plate rotation | |
| 16051 | IMAGE: DPE orthog slope larger than max, check plate rotation | |
| 16068 | IMAGE: Unable to initialize plot for mode set to 0 DPI | |
| 17046 | HEAD: multiple edges detected - verify image position | |
| 17501 | HEAD: temperature out of range | |
| 17502 | HEAD: value out of range | |
| 17503 | HEAD: missing laser on parameters | |
| 17504 | HEAD: attempted write blocked | |
| 17505 | HEAD: failure to write to memory | |
| 17506 | HEAD: unsupported message | |
| 17507 | HEAD: message length incorrect | |
| 17508 | HEAD: invalid control message | |
| 17509 | HEAD: operation was aborted | |
| 17532 | HEAD: no more room in mailbox | |
| 17533 | HEAD: ran out of buffers | |
| 17534 | HEAD: all retries failed on chnl 0 | |
| 17535 | HEAD: all retries failed on chnl 1 | |
| 17536 | HEAD: sync lost on chnl 0 | |
| 17537 | HEAD: sync lost on chnl 1 | |
| 17548 | HEAD: CONFIG register incorrect | |
| 17549 | HEAD: flash memory checksum error | |
| 17550 | HEAD: LCA won't init for reprogram | |
| 17551 | HEAD: LCA won't admit being loaded | |
| 17552 | HEAD: SRAM memory check failure | |
| 17596 | HEAD: software error | |
| 17597 | HEAD: LCA config unavailable | |
| 17692 | HEAD: Light level too low for Beam Pointing | |
| 17693 | HEAD: Timeout waiting for LASER OK | |
| 17694 | HEAD: Light valve high voltage fault | |
| 17695 | HEAD: LV Positive 12V fault (bipolar) | |
| 18017 | LASER: Cannot continue, laser is not ready | |
| 19000 | PDB: Air Supply Below Threshold | |
| 21000 | SCSI: SCSI bus reset while imaging | |
| 21001 | SCSI: SCSI parity error while imaging, check plate for artifacts | |
| 21002 | SCSI: SCSI driver error, invalid initiator | |
| 21003 | SCSI: SCSI Driver Error, line <line number> | |
| 21004 | SCSI: SCSI asynchronous transfer requested, line <line number> | |
| 21005 | SCSI: timed out waiting for SCSI complete | |
| 30000 | TPG: memory overflow | |
| 30001 | TPG: too many scans | |
| 30002 | TPG: write to closed scan | |
| 30003 | TPG: write to unopened scan | |
| 30004 | TPG: write to undefined scan | |
| 30005 | TPG: close of closed scan | |
| 30006 | TPG: close of unopen scan | |
| 30007 | TPG: open of NULL scan | |
| 30008 | TPG: Undefined pattern number, use "list pattern" | |
| 30009 | TPG: Call with NULL pattern struct | |
| 30010 | TPG: Pattern write call error | |
| 30011 | TPG: Too many cells in pattern | |
| 30012 | TPG: timed out waiting for stripe to complete | |
| 31002 | LCA: DONE signal stuck low while programming | |
| 31003 | LCA: READY signal stuck low while programming | |
| 31004 | LCA: did not accept programming data | |
| 31006 | LCA: INIT signal stuck low while programming | |
| 31007 | LCA: INIT signal stuck high while programming | |
| 31008 | LCA: Required LCA file is not in firmware | |
| 31009 | LCA: Required LCA master file is not in firmware | |
| 31010 | LCA: Length of LCA diff file does not match master | |
| 32200 | SW: Ink Key buffers out of synch | |
| 32201 | SW: Image shutdown error | |
| 32202 | SW: NCO update timeout | |
| 32203 | SW: Resolution mode not defined | |
| 32301 | SW: Unknown ID code in firmware directory | |
| 32302 | SW: undefined subsystem in NVS list | |
| 32401 | SW: Could not open console interface for serial communications | |
| 32403 | SW: Could not open head interface for serial communications | |
| 32404 | SW: Could not open laser interface for serial communications | |
| 32450 | SW: Out of memory | |
| 32480 | SW: WS data list unexpectedly in use | |
| 32481 | SW: WS command pattern incorrect | |
| 32490 | SW: AL Sched: pick sync error | |
| 32491 | SW: AL Sched: unload sync error | |
| 32492 | SW: AL Sched: load sync error | |
| 32493 | SW: AL Sched: process sync error | |
| 32500 | SW: Unexpected SW failure - general exception | |
| 32600 | SW: executive call failed | |
| 32601 | SW: executive call tsk_create() failed | |
| 32602 | SW: executive call tsk_delete() failed | |
| 32603 | SW: executive call tsk_suspend() failed | |
| 32604 | SW: executive call tsk_resume() failed | |
| 32605 | SW: executive call tsk_set_priority() failed | |
| 32606 | SW: executive call mbx_create() failed | |
| 32607 | SW: executive call mbx_delete() failed | |
| 32608 | SW: executive call mbx_send() failed | |
| 32609 | SW: executive call mbx_receive() failed | |
| 32610 | SW: executive call mbx_flush() failed | |
| 32611 | SW: executive call buf_alloc() failed | |
| 32612 | SW: executive call buf_free() failed | |
| 32613 | SW: executive call tmr_create() failed | |
| 32614 | SW: executive call tmr_delete() failed | |
| 32615 | SW: executive call pip_create() failed | |
| 32616 | SW: executive call pip_delete() failed | |
| 32617 | SW: mbx_send failed, NULL mailbox | |
| 32618 | SW: mbx_send failed, mailbox full | |
| 32700 | SW: all tasks suspended | |
| 32701 | SW: Unexpected message in mailbox <mailbox name>, message code <hex message code> | |
| 32702 | SW: message buffer request failed | |
| 32703 | SW: message buffer release failed | |
| 32704 | SW: string buffer request failed | |
| 32705 | SW: string buffer release failed | |
| 32706 | SW: unexpected case - file:<filename> line:<line number> | |
| 32707 | SW: image command received by active task | |
| 32708 | SW: procedure call has invalid parameters | |
| 32709 | SW: status mask has duplicate flags defined | |
| 32711 | SW: Unexpected message type for this command. type: <hex message type> | |
| 32766 | SW: Non-specific error | |