Home | Contact Us | Submit Troubleshooting Info | Search | Help
Output | Software Solutions | Proofing | Color, Screening and Calibration | Scanning | Digital Photography | Consumables | POS
Home | Contact Us | Submit Troubleshooting Info | Search | Help
Output | Software Solutions | Proofing | Color, Screening and Calibration | Scanning | Digital Photography | Consumables | POS
Main Firmware | BMM | BBR | Boot code | Recovery code | SNIF
The main operating firmware that controls the satellite I/O board during normal operation. Resides in a field eraseable flash sector.
Caution: Ensure you have at least BBR ver 1.03 or later already installed before attempting to upgrade the satellite board firmware over the CAN Bus.
| Version | Status | Part # / ECO | Date | Notes |
| 1.17 | Unreleased | Dec 2002 | ||
| 1.16 | Released | 19-3412A /E857 | Nov 2002 | |
| 1.15 | Released | Release Notes | ||
| 1.14 | Released | Release Notes | ||
| 1.13 | Released | Release Notes | ||
| 1.12 | Released | Release Notes | ||
| 1.11 | Released | Release Notes | ||
| 1.10 | Released | Release Notes | ||
| 1.09 | Released | Release Notes | ||
| 1.08 | Released | Release Notes | ||
| 1.07 | Released | Release Notes | ||
| 1.06 | Released | Release Notes | ||
| 1.05 | Released | Release Notes | ||
| 1.04 | Released | Release Notes | ||
| 1.03 | Released | Release Notes |
The BMM programming card is used to load the Boot Block Recovery (BBR) code. The *bmm.bin files contain both the BBR code and the Boot code.
| Version | Status | Part # / ECO | Date | Notes |
| 1.09 | Released | 19-3409A /E857 | Nov 2002 | |
| 1.08 | Released | |||
| 1.07 | Released | |||
| 1.06 | Released | |||
| 1.05 | Released | |||
| 1.04 | Released | |||
| 1.03 | Released | |||
| 1.02 | Released |
Boot Block Recovery Code. This code runs from the protected flash boot-block sector and is only re-programmable by using the BMM card. See BMM programmable card for downloads.
| Version | Status | Part # / ECO | Date | Notes |
| 1.03 | Released |
Runs from a field eraseable flash sector. Allows downloading of the main firmware across the CAN bus.
Caution: Ensure you have at least BBR v1.03 or newer already installed before attempting to upgrade satellite board firmware over the CAN Bus. V1.09 Boot code now defaults to 500KHz, while previous versions use 909KHz!
| Version | Status | Part # / ECO | Date | Notes |
| 1.09 | Released | 19-3411A /E857 | Nov 2002 | Use BMM programming card version 1.09 |
| 1.08 | Released | Use BMM programming card version 1.08 | ||
| 1.07 | Released | Use BMM programming card version 1.07 | ||
| 1.06 | Released | Use BMM programming card version 1.06 | ||
| 1.05 | Released | Use BMM programming card version 1.05 | ||
| 1.04 | Released | Use BMM programming card version 1.04 | ||
| 1.03 | Released | Use BMM programming card version 1.03 | ||
| 1.02 | Released | Use BMM programming card version 1.02 |
This firmware is downloaded over the diagnostic serial port when the BBR is running. Use the Bload.exe utility v1.09 or newer. Normally this will never be required, unless the BBR could not find valid Boot code.
| Version | Status | Part # / ECO | Date | Notes |
| 1.00 | Released | 19-3410A /E857 | Nov 2002 | Download over serial port. |
Genine board SNIF diagnostic firmware.
| Version | Status | Part # / ECO | Date | Notes |
| 1.03 | Released | 19-3414A /E857 | Nov 2002 | |
| 1.02 | Released | |||
| 1.00 | Released |