When white lines (banding) appear on Agfa Amigo plates with AM or FM screening that are imaged at the specified power and drum speed, reduce the laser power and drum speed to maintain the 240 mJ/cm2 exposure.
Go to Image quality on the Troubleshooting page.

If the Write cache enabled check box is not selected, the cache memory is not saved.
Go to Performance on the Troubleshooting page.

FCO 512-00492A installs the improved power distribution board (PDB) to prevent board burn-out due to continuous drum vacuum pump operation.
Go to the FCOs page.

To maximize uptime for the Magnus 400 II family platesetters and as part of the planned maintenance (PM) regimen, fill out the online interactive Magnus 400 II PM checklist.
Go to Planned maintenance on the Maintenance page.

This procedure describes how to remove and install the power distribution board (PDB).
Go to Parts replacement on the Procedures page.

This procedure describes how to remove and install the leadscrew.
Go to Parts replacement on the Procedures page.

The difference in distance between the inner registration pin and the outer registration pin is 0.5 mm. To ensure that your plate is properly aligned for plate exposure, adjust the Width Start Image Area parameter.
Go to Technical bulletins on the Reference page.

If the drum motor fails to rotate the drum, rotates the drum in the wrong direction, or is excessively noisy, you might need to replace the drum motor. This procedure describes how to remove and install the drum motor.
Go to Parts replacement on the Procedures page.

Use the Magnus 400 II Family Visual Reference Guide (VRG) to help you maintain and operate the Magnus 400 II and Magnus 400 II Quantum platesetter configurations.
The VRG is available in 25 languages.
Go to Visual Reference Guides (VRGs) on the Reference page.

Follow the procedures in the Magnus 400 II Quantum Hardware Installation Guide to install the Magnus 400 II Quantum platesetter and (optional) plate conveyor at the customer's site.
For platesetters with the punch conveyor configuration, see the Punch Conveyor Hardware and Software Installation Guide.
Go to Installation procedures on the Installation page.

See the Cold Start Software Installation Guide for Magnus 400 Controller 1.05.394 whenever you need to perform an installation of the Magnus 400 Controller 1.05.394 software from the beginning.
Go to Installation procedures on the Installation page.

Version 1.05.394 includes support for the bypass option, punch conveyor, diode cross connection and more. Learn about these and other features that appear in the Magnus 400 Controller 1.05.394 Release Notes and Software Installation Guide.
Go to Release notes on the Reference page.

Two versions of the Magnus 400 Component Finder are available on TechPlanet: a web-based version, which is a browser enabled, searchable database containing all the Magnus 400 components, and a downloadable version.
Go to Tools on the Parts/tools page, or Component finder on the Reference page.

Magnus 400 Quantum firmware versions for the Magnus 400 Controller 1.05.394 software are now available.
Go to Firmware on the Downloads page.

The Magnus 400 II and Magnus 400 II Quantum Safety Precautions for Service is available for EP.
Go to Service engineer on the Safety page.

The part number for the Basic PM Kit for Quantum configurations with MCU has been promoted from 518-01320A to 518-01320B. In addition to the Lotem Quantum with MCU configuration, the updated part number is relevant also to the Magnus 400 Quantum with MCU and Magnus 400 II Quantum with MCU II configurations.
Go to the Parts/tools page.

This procedure describes how to use the Magnus Output Devices Installation Report Tool. The tool enables field engineers to provide installation feedback to Kodak. After every installation, open the Magnus Output Devices Installation Report Tool and submit the report.
Go to the Installation page.

The Magnus 400 II and Magnus 400 II Quantum Safety Precautions for Operators guide is available in English. Translations will be available later this year.
Go to the Safety page.

The Magnus 400 II and Magnus 400 II Quantum Site Preparation Guide is available in the following languages: Danish, Dutch, French, German, Italian, Norwegian, Portuguese, Spanish, and Swedish.
Changes made after the translation cycle will appear only in the English version with links to the updated information under the Site Preparation subcategory Updates.
Go to the Installation page.

The English version of the Magnus 400 II and Magnus 400 II Quantum Site Preparation Guide is now available. Translations will be available in February 2008.
Go to the Installation page.

Each time that you replace a thermal imaging head, you must fill out the Exposure head request (EHR) form and notify all members on the #CEM-EH Request list.
For more information about returning thermal heads, see Replacing a thermal head.
Go to the Parts/tools page.

The Magnus 400 II Quantum site is now live, and includes product description information. We will continue to add information to the site.