Home | Contact Us | Submit Troubleshooting Info | Search | Help


    Output | Software Solutions | Proofing | Color, Screening and Calibration | Scanning | Digital Photography | Consumables | POS

MCE Diagnostic Commands

ContinuousLoad specific Commands | Base Trendsetter Commands

See also Search Form

Diagnostic Commands specific to Trendsetter CL

TBD

Base Trendsetter Diagnostic Commands

This content is generated by scripts that pull information directly from Firmware Engineering's support site. The scripts were last run: 16 Jul 2008 17:30:49

Command
a
a
a clear
a clear
abort
abort
abort clear
abort clear
abort faults
abort faults
access
access
access dev
access disable
access enable
access expert
access field
ale
autocalibrate [ i ] [ < media_type > ]
autocalibrate [ i ] [ < media_type > ]
autocalibrate args
autocalibrate info
bay
bay
bay < bay_number >
bay < bay_number > close
bay < bay_number > load < quantity > [ m ] [ < mlength > ]
bay < bay_number > measure [ calibrate ]
bay < bay_number > open
bay < bay_number > transfer
bay < bay_number > transfer < to_bay_number > < quantity >
bay < bay_number > unload
bay cancel
bay fail
bay fail < string >
bay info
bay init
bay release
bay step
bay step < enable | disable >
bay time
bay transfer
bay transfer < count >
bcm
bcm bxi
bcm bxi < channel > cb [ bcm ]
bcm bxi < channel > gets
bcm bxi < channel > priority < pri >
bcm bxi < channel > puts < string >
bcm bxi < channel > selftest < string > [ [ < repeat > ] ]
bcm close
bcm commcheck
bcm diag
bcm diag com < com_port >
bcm diag pipe < pipe_num >
bcm diag reset
bcm diag reset com < com_port >
bcm diag reset pipe < pipe_num >
bcm diag reset scc < scc_port >
bcm diag scc < scc_port >
bcm dne
bcm dne < dne_num >
bcm icecheck
bcm open
bcm ping
bcm pipeinfo
bcm res
bcm test
bcm ver
board
board address
bos
bos
can
can
can buf
can diag
can reg
can watch [ < port > ]
cancel
cancel
carriage
carriage
carriage data [ < on | off > ]
carriage idle
carriage init
carriage irq [ < enable | disable > ]
carriage move < velocity >
carriage moveto < position > [ [ < velocity > ] ]
carriage plot < swathwidth > < swathcount > < drumspeed > < indexdelay >
carriage run
carriage sim [ < enable | disable > ]
carriage stop
carriage table
ceh
ceh
ceh edge info
ceh edge mode < edge mode >
ceh edge reset
ceh fault state
ceh focus cal reflect
ceh focus laser < laser mode >
ceh focus mode < focus mode >
ceh focus ramp < pedestal > < slope > < length > < start >
ceh focus state
ceh head command < head command >
ceh head compatible
ceh head environment
ceh head info
ceh head mode < head mode > [ [ < head type > ] ]
ceh head state
ceh log < parameter >
ceh lv pattern < pixel pattern > +
ceh lv pattern off
ceh media block read < media slot >
ceh media block write < media slot >
ceh media query < media specifier >
ceh media set < media specifier >
ceh media slot < media slot > < media specifier >
ceh plot command < plot command >
ceh plot config < data source > < pattern > < polarity > < label >
ceh property read < id > [ [ < index > ] ]
ceh property write < id > < value > [ [ < index > ] ]
ceh punch < sscan shift > < sscan width > < mscan shift > < mscan length >
ceh setup head position < position mode >
ceh shutter control < shutter type > < shutter control >
ceh stroke cal initiate
ceh stroke cal required
ceh stroke cal state
ceh test crc reset [ < data mask > ]
ceh test crc state
ceh test data mode < data mode >
ceh test data reset
ceh test data state
ceh write laser info
ceh write laser mode < laser mode >
ceh write laser state
CFL
CFL connect [ < id > ]
CFL diag
CFL disconnect [ < id > ]
CFL query [ < id > ]
cfs
cfs cd < dirname >
cfs dir
cfs md < newdirname >
cfs rd < rdname >
cfs version
chiller
chiller
component
component
component < name > [ online ] | [ offline ]
config [ < password > + ]
config [ < password > + ]
db < address > [ < quantity > ]
db < address > [ < quantity > ]
debris
debris
debris < opt >
debris < opt > < on | off >
debris airjet
debris airjet < on | off >
debris all off
debris blower
debris blower < on | off >
debris debug
debris flexo
debris flexo < on | off >
debris ibutton
debris ibutton setup default [ force ]
debris ibutton setup filter < usage > [ force ]
debris ibutton setup max < usage > [ force ]
debris options
debris pacc
debris pacc < on | off >
debris poc
debris poc < on | off >
debris sim
debris sim < on | off >
debris test bellmouth < value >
debris test differential < value >
debris test nozzle < value >
debris trace
debris trace2
df1
df1
df1
df1 diag
df1 handle
dl < address > [ < quantity > ]
dl < address > [ < quantity > ]
dlp < enable | disable >
dlp < enable | disable >
dlp < enable | disable >
dlp metadata
door
door
door lock
door lock
door unlock
door unlock
dpc
dpc block < on | off >
dpc diag
dpc end
dpc msg < on | off >
dpc ovwr
dpc ovwr < pattern >
dpc retrace
dpc retrace < enable | disable >
dpc retrace delay
dpc retrace delay < value >
dpc scsi
dpc scsi cdb
dpc scsi config
dpc scsi end
dpc scsi flags
dpc scsi pause
dpc scsi resume
dpc scsi start
dpc scsi state
dpc scsi total
dpc start < pattern >
dpc start scsi
dpc stop scsi
dpc strip
dpc strip < on | off >
dpc test memory < pattern > [ [ < iterations > ] ]
dpc tpg query
dr
dr
drum
drum
drum cshow
drum etrace [ < enable | disable | show > ]
drum idle
drum init
drum move < position > [ [ < velocity > ] | [ s ] ]
drum patch [ < offset > ]
drum sim [ < enable | disable > ]
drum smove < position > [ [ < velocity > ] | [ s ] ]
drum spin < velocity >
drum sstopat < position >
drum static
drum stop
drum stopat < position >
drum torque < drive >
dtl
dtl
dtl diag
dualbay
dualbay arms < in | out >
dualbay cylinder < in | out >
dualbay deploy
dualbay retract
dualbay stacker < in | out >
dummy
dummy
dummy
dw < address > [ < quantity > ]
dw < address > [ < quantity > ]
edge
edge
edge away [ < enable | disable > ]
edge stop
edge test
edge test camera
edge test mainscan
edge test plate < plateid >
edge test plate < plateid > camera
edoor
edoor
edoor < open | close > [ w ]
edoor < open | close > [ w ]
eject
eject
engine
engine
engine accuracy
engine accuracy
engine cancel
engine cancel
engine fail
engine fail
engine fail < string >
engine fail < string >
engine init
engine init
engine moveto loadpos
engine moveto loadpos
engine moveto parkpos
engine moveto parkpos
engine moveto unloadpos
engine moveto unloadpos
engine release
engine release
engine set loadpos
engine set loadpos
engine set parkpos
engine set parkpos
engine step
engine step
engine step < enable | disable >
engine step < enable | disable >
engine time
engine time
error
error
error
error list
error param
error reserve < errorid >
error test [ fatal ]
error unreserve < errorid >
event [ < value > ]
event [ < value > ]
fans
fans
fans < on | off >
fans < on | off >
fco
fco
fco < component >
fco < component > < label >
fco < component > < label > < on | off >
feature [ < password > + ]
feature [ < password > + ]
feature list
feature list
feature list current
feature list current
feature remove
feature remove
feature remove < tag >
feature remove < tag >
fload
fload
fload binary head bundle
fload binary head code
fload head bundle
fload head code
flush
flush
flyoff
flyoff
flyoff clear
flyoff clear
focus < focus mode >
focus < focus mode >
focus cal [ < cal mode > ]
focus laser < focus laser >
focus lpos off
focus lpos on < lens position >
focus position
fw
fw dir
fw erase ovwr
fw erase post
fw load boot
fw load boot sat
fw load lca
fw load main
fw load main sat
fw load nvs flash
fw load nvs ram
fw load post
fw save nvs flash
fw save nvs ram
fwd
fwd
fwd list
fwd optimize
fwd validate
fwd version
gc
gc
gc init
gc init
getclamp
getclamp
gim
gim
gim bypassprompt ignore
gim carriage
gim carriage reset
gim cds
gim cds reset
gim drum
gim drum error
gim drum reset
gim edge
gim edge reset
gim lamp < mask > < off | on | flash >
gim latch
gim latch < number > trigger
group
group
group end < index >
group start < index > < headid1 > < plateid1 > [ [ < headid2 > ] [ < plateid2 > ] ]
head
head
head boot [ < brate > ]
head bp
head bp < bp current >
head bp < bp mode >
head debug bank < bank offset > < bank size >
head debug heap
head debug interrupt
head debug nvs < nvs offset > < nvs size >
head debug ram < ram address > < ram size >
head debug stack
head debug stats
head debug structure < structure index >
head debug trace < trace mode >
head edge < edge mode >
head end
head erase bundle
head erase code
head flatten [ < flatten scale > ]
head init
head install < install mode > [ [ < thickness > ] ]
head interval < status interval >
head mask [ < mask mode > < mask number > + ]
head mask save
head nvs [ < parameter group > ]
head nvs checksum
head position
head position
head position < subscan > [ < mainscan > ]
head position < subscan > [ < mainscan > ]
head position < subscan > [ < mainscan > ]
head power [ < power mode > ]
head program
head read < offset > < size >
head recover
head reset
head reset < reset mode >
head sample < sample mode >
head stats bp [ < hold current > ]
head stats dtd < laser on time >
head stats media [ init ] [ < slots > + ]
head status [ < status mode >
head status lvd [ < io register > ] [ [ < register value > ] ]
head stream < stream mode >
head test
head version
help
help
help < search > +
help < token > +
help -all
help -all < token > +
help -brief
help -debug [ all ]
help -tree
help -tree < token >
history
history
history
history < enable | disable >
history display
hlt
hlt
hlt listdebug
hlt puonline
hlt puonline < unit > 0
hlt puonline < unit > 1
hlt reg < subsystem > < errorcode > < timeout >
hlt rep < subsystem > < errorcode >
hlt shutdown system
hlt status
hlt status < subsystem >
hlt status dne
hlt status pu
hlt status subsystems
hlt status system
hlt status ws
hlt test < timeout1 > < timeout2 > < timeout3 > < timeout4 > < timeout5 >
hlt update ws
hlt uptime
hotlink < endis >
hotlink < endis >
hotlink reset
hotlink status
ibm
ibm
ibm nodes < port > < boardid >
ibm scan [ < name > < value > + ]
ibm setup < port > < boardid > < nodenum > < version > < creotype > < number >
image [ < taskid >
image [ < taskid >
image cancel [ < taskid > ]
image end [ < taskid > ]
image flush
image flush end
image params [ < taskid > ]
image parm
image parm < param >
image parm < param > < value >
image parm < param > default
image start [ < taskid > ] | [ < mainscan > ] | [ mediapending ] | [ datapending ]
image stats
image stats clear
image update [ < taskid > ] | [ loaded ] | [ dataready ]
init [ info ] | [ args ] | [ m ] [ < mlength > ]
init [ info ] | [ args ] | [ m ] [ < mlength > ]
laser
laser
laser < laser mode >
laser current < laser current >
laser ship
laser test
latch
latch
latch < number >
latch < number > < enable | disable >
latch < number > setup < sensor > < rise | fall >
lca
lca
lca bstrace < enable | disable >
lca bstrace dump
lca fwdbg
lca fwdbg < value >
lca irq
lca irq reset
lca load
lca spddump
lca trace < enable | disable >
lca trace dump
leave on
leave on
lec
lec
lec < on | off > [ w ]
lec < on | off > [ w ]
lec init
lec init
license
license limit < tag > [ [ < value > ] ]
list
list
list
list datatypes
list error [ < errorcode > ]
list map
list media
list media types
list ovwr
list pattern [ < number > ]
list proof
list serial
list stats
list version
list version all
list version version [ d ] | [ s ]
load [ info ] | [ args ] | [ m ] [ < mlength > ]
load [ info ] | [ args ] | [ m ] [ < mlength > ]
loaded [ s ] [ < slength > ]
loaded [ s ] [ < slength > ]
loaded force [ info ] | [ args ] | [ none ] | [ m ] [ < mlength > ]
lockout [ < enable | disable > ]
log
log
log
log clear
log disp [ < tmode > ] | [ < tunits > ] | [ < fmask > ] | [ < emask > ]
log mark [ < id > ]
log mask
log mask < fmask >
log mask < fmask > < emask >
log source
log source disable < label >
log source disable all
log source enable < label >
log source enable all
log start [ < count > ] | [ full ]
log status
log stop [ < count > ]
macro
macro
macro create < name > < command > +
macro delete < name >
macro delete -all
mask
mask
mask < on_off > < flag > +
mask < on_off > all
mask all
mce
mce baud < baudrate >
mce irq
mce term
mce version
media
media
media < number >
media lru
media lru reset
media removed
media removed
media types
mh
mh
mh awayplateload
mh cycletest
mh cycletest
mh cycletest < enable | disable >
mh cycletest < enable | disable >
mh plateless
mh plateless
mh plateless < enable | disable >
mh plateless < enable | disable >
mload
mode
mode
mode < number >
mode dpi < mainscan > [ [ < subscan > ] ]
mode media < number >
mode media < number >
mode vmr < mainscan > < realmainscan >
mpi
mpi
mpi diag
msg
msg
msg res
msg trace
msg trace < on | off >
msg trace dump
msg trace filter < cmdcode > +
msg trace filter list
msg trace filter remove < cmdcode > +
msg trace filter remove all
munload
net < if > ipaddr < newipaddr >
net < if > netmask < newnetmask >
net < on | off >
net < on | off >
net arp
net arp add
net arp delete
net bootp [ < on | off > ]
net cospeed < speed > < duplex >
net diag
net gateway < newgateway >
net loopdevtest < loopc > < datasize >
net looptest < loopc > < datasize >
net newaccount < n > < name >
net newpassword < n > < password >
net ping < ipaddr >
net pktfwd < on | off >
net route
net route add < if > < ipaddr > < netmask > < gateway > < hops >
net route delete < ipaddr > < netmask >
net socket
net status
net tcp
net udp
nl < offset > < width >
nl < offset > < width >
notused_ftr
notused_ftr
notused_hdr
notused_hdr
ntpipe
ntpipe
ntpipe
ntpipe status
nucdebug
nucdebug
nucdebug
nvs
nvs
nvs save all [ < code > ] [ < subsys > ]
opt < OptionToken >
opt < OptionToken >
opt < OptionToken >
option
option
option autoloader [ < enable | disable > ]
option continuousload [ < enable | disable > ]
option debris udrcb [ < enable | disable > ]
option debris udrcb [ < enable | disable > ]
option dual-bay [ < enable | disable > ]
option dual-head [ < enable | disable > ]
option dual-plate [ < enable | disable > ]
option edgedetect [ < enable | disable > ]
option edgedetect [ < enable | disable > ]
option film-guide [ < enable | disable > ]
option film-guide [ < enable | disable > ]
option list
option list
option narrow-format [ < enable | disable > ]
option no-buzzer [ < enable | disable > ]
option no-buzzer [ < enable | disable > ]
option outrigger [ < enable | disable > ]
option outrigger [ < enable | disable > ]
option preloader [ < enable | disable > ]
option processorinterface [ < enable | disable > ]
option processorinterface [ < enable | disable > ]
option rotator [ < enable | disable > ]
option rotator [ < enable | disable > ]
option separator-arms [ < enable | disable > ]
option separator-arms [ < enable | disable > ]
option single-broadsheet [ < enable | disable > ]
option single-broadsheet [ < enable | disable > ]
option universal-drum [ < enable | disable > ]
option universal-drum [ < enable | disable > ]
option unload-offset [ < enable | disable > ]
option unload-offset [ < enable | disable > ]
option vmr [ < enable | disable > ]
option vmr [ < enable | disable > ]
option zstage [ < enable | disable > ]
override
override
override
override < TableName >
override showall
ovwr
ovwr
ovwr < enable | disable >
ovwr dump < pattern >
ovwr list
ovwr load < pattern >
ovwr mask end
ovwr mask end < value >
ovwr mask loc
ovwr mask loc < value >
ovwr mask start
ovwr mask start < value >
ovwr verify
owb
owb
owb
owb nodes < port >
owb open < port >
owb read < port > < id1 > < id2 > < id3 > < id4 > < id5 > < id6 > < id7 > < id8 > < address > < amount >
owb write < port > < id1 > < id2 > < id3 > < id4 > < id5 > < id6 > < id7 > < id8 > < address > < data > +
pb < map_name > < hex_address > [ < hex_data > ]
pb < map_name > < hex_address > [ < hex_data > ]
pb < map_name > < hex_address > [ < hex_data > ]
phy
phy
phy cablelength
pick
picker
picker < ajet | airjet > < on | off >
picker < in | out > [ w ]
picker < pvac | powervac > < on | off >
picker < up | down | dn > [ w ]
picker arm < in | out >
picker cancel
picker cups < in | out > [ w ]
picker cylinder < in | out >
picker fail
picker fail < string >
picker init
picker lock < on | off >
picker pick
picker release
picker sep < in | out > [ w ]
picker service
picker stacker < in | out >
picker step
picker step < enable | disable >
picker switchoverBay1
picker switchoverBay2
picker time
picker vac < on | off > [ w ]
picker vac_away < on | off > [ w ]
picker vac_home < on | off > [ w ]
picker wrist in [ w ]
picker wrist in fast
picker wrist out [ w ]
pl < map_name > < hex_address > [ < hex_data > ]
pl < map_name > < hex_address > [ < hex_data > ]
pl < map_name > < hex_address > [ < hex_data > ]
pll
pll
pll < on | off >
pll stats [ < samples > ]
pload
pload
pload c < proof_index >
pload d < media_index >
pload r
plot
plot
plot < pattern >
plot < pattern > < subscan > [ < mainscan > ]
plot < pattern > < subscan > plate < plateid >
plot < pattern > plate < plateid >
plot [ s ] < slength >
plot [ s ] < slength >
plot balance
plot balance < interval >
plot crc
plot crc < enable | disable >
plot crc < value > [ < headid > ]
plot debug
plot debug < level >
plot edge
plot edge < enable | disable >
plot edge < position >
plot edge < position > plate < plateid >
plot event < code >
plot events
plot fail
plot fail < event >
plot focus
plot focus < learns >
plot gapless
plot gapless < enable | disable >
plot gc
plot gc < enable | disable >
plot gc rotation < enable | disable >
plot gc scaling < enable | disable >
plot gc tempcomp < enable | disable >
plot headtest [ < mainscan > ]
plot init
plot label
plot label < label text >
plot label default
plot moffset
plot moffset < subscan > [ < mainscan > ]
plot ortho
plot ortho < enable | disable >
plot polarity
plot polarity < polarity type >
plot prepare [ info ] | [ args ] | [ m ] [ < mlength > ]
plot reset
plot scale
plot scale < subscan > [ < mainscan > ]
plot seam
plot seam < enable | disable >
plot seam < number > < rect | lane > < offsetX > < offsetY > < endX > < endY >
plot seam clear
plot sequence
plot series
plot series < enable | disable >
plot series drumspin < enable | disable >
plot series gap < spacing >
plot shift
plot shift < subscan > [ < mainscan > ]
plot skip [ < swath > < count > ]
plot skip remove
plot skip update < count >
plot stop
plot stroke
plot stroke < shift >
plot time
plot time reset
post
post clear
post reload [ < BoardId > ]
post reset
post results [ < BoardId > ]
post test < BoardId > < TestId > [ [ < TestMode > ] ]
preloader
preloader test docked < enable | disable >
preloader test pickerclear < enable | disable >
preloader test requestplate < enable | disable >
prm < groupname > [ [ limit ] | [ < copy > ] [ < parameter > ] [ default ] | [ all ] [ s ] | [ default ] | [ < value > ] [ s ] ]
prm < groupname > [ [ limit ] | [ < copy > ] [ < parameter > ] [ default ] | [ all ] [ s ] | [ default ] | [ < value > ] [ s ] ]
prm < search > +
prm access [ < level > ]
prm all
prm diff
prm group
prm limit
prm saveall
prmdef < key >
prmdef < key >
processor
processor test < notready | ready | busy | busyfault | idlefault >
product
product
property
property
property read [ < number > ] [ [ < index > ] [ < secondaryindex > ] ]
property write < number > < index > < secondaryindex > < value >
punload
punload
putclamp
putclamp
pw < map_name > < hex_address > [ < hex_data > ]
pw < map_name > < hex_address > [ < hex_data > ]
pw < map_name > < hex_address > [ < hex_data > ]
ramp
ramp
ramp < in | out > [ w ]
ramp < in | out > [ w ]
ramp bottom
ramp bottom < in | out > [ w ]
ramp top
ramp top < in | out > [ w ]
redirect [ < endis > ]
redirect [ < endis > ]
redirect file < filename >
redirect pass
redirect passthrough
release
release
reset
reset
reset
reset all
reset bbr
reset boot
reset cold
reset head
reset partial
reset post
resume
resume
rif
rif
rif res
rif ver
rlr [ < token > + ]
rlr [ < token > + ]
roller
roller
roller < on | off > [ w ]
roller < on | off > [ w ]
roller init
roller init
rtl
rtl address
rtl diag
rtl diag reset
rtl diag reset bcm
rtl ping < x > < y > < z >
rtl res
rtl resetbcmdiag
rtl resetdiag
rtl routing
rtl trans
rtl transdump
rtl ver
run < Filename >
run < Filename >
run < Filename >
safety
safety
safety abortfn
safety abortfn
safety move
safety move
safety spin
safety spin
scan < ioname > [ [ addr ] | [ < on | off > ] | [ < value > ] | [ < bon | boff > ] | [ < son | soff > ] ]
scan < ioname > [ [ addr ] | [ < on | off > ] | [ < value > ] | [ < bon | boff > ] | [ < son | soff > ] ]
scan bclear
scan bits
scan bstatus
scan events
scan groups
scan presence
scan time [ clear ]
scanline
scanline
scanline read < scanlinenum >
scanline read < scanlinenum > < offset > [ < numwords > ]
scanline write < scanlinenum > < offset > < data >
scheduler
scheduler
scheduler < media_instance >
scheduler < media_instance > cancel
scheduler < media_instance > steps
scheduler autounload
scheduler autounload < enable | disable >
scheduler cycletest
scheduler cycletest < enable | disable >
scheduler debug
scheduler mediatypes
scheduler stats
scheduler stats clear
scheduler tasks
scorr
scorr
scorr < pixel pair >
scorr < pixel pair > < scorr value >
scorr init [ < scorr value > ] [ [ < scorr slope > ] ]
scorr save
sdram
sdram size
sdram test [ < startaddress > < endaddress > [ < percentage > ] ]
service [ info ] | [ args ] | [ m ] [ < mlength > ]
service [ info ] | [ args ] | [ m ] [ < mlength > ]
set < search > +
set [ < groupname > ] [ [ < copy > ] [ < parameter > ] [ < val_element > ] [ < value > ] ]
set [ < groupname > ] [ [ < copy > ] [ < parameter > ] [ < val_element > ] [ < value > ] ]
shutter < shutter control > [ [ hw ] ]
shutter < shutter control > [ [ hw ] ]
sif
sif
sif
sif diag
sif rd < sport > < bid > < vaddr >
sif read < bid > < vaddr >
sif test read < bid > < vaddr >
sif test write < bid > < vaddr > < data > +
sif wr < sport > < bid > < vaddr > < data > +
sif write < bid > < vaddr > < data > +
sim
sim
sim all [ < enable | disable > ]
sim all [ < enable | disable > ]
sim bay [ < enable | disable > ]
sim car [ < enable | disable > ]
sim car [ < enable | disable > ]
sim drum [ < enable | disable > ]
sim drum [ < enable | disable > ]
sim engine [ < enable | disable > ]
sim engine [ < enable | disable > ]
sim head [ < enable | disable > ]
sim head [ < enable | disable > ]
sim mh [ < enable | disable > ]
sim mh [ < enable | disable > ]
sim pdb [ < enable | disable > ]
sim pdb [ < enable | disable > ]
sim picker [ < enable | disable > ]
sim preloader [ < enable | disable > ]
sim processor [ < enable | disable > ]
sim saveall
sim saveall
sim table [ < enable | disable > ]
sio
sio
sio con < bid >
sio nodes
sio reset all
sio reset single < bid >
sio uns
slipsheet bin
slipsheet bin
slipsheet bin < bin_number > unload
slipsheet bin args
slipsheet bin info
smc
smc
smc < name >
smc < name > current
smc < name > current < zero | quarter | half | full >
smc < name > dirmode
smc < name > dirmode < homeccw | homecw >
smc < name > follow < maximumVelocity > < lastValid > < home | away >
smc < name > followr < maximumVelocity > < lastValid > < home | away >
smc < name > gain
smc < name > gain < outputGain >
smc < name > home < velocity >
smc < name > homer < velocity >
smc < name > hwreset
smc < name > init
smc < name > jog < maximumVelocity > < acceleration > < steps >
smc < name > jogr < maximumVelocity > < acceleration > < distance >
smc < name > micro
smc < name > micro < microstepRate >
smc < name > move < maximumVelocity > < acceleration > < position >
smc < name > mover < maximumVelocity > < acceleration > < position >
smc < name > position
smc < name > position < newPosition >
smc < name > positionr
smc < name > positionr < newPosition >
smc < name > query [ vel ] | [ accel ] | [ micro ] | [ vmax ] | [ steps ] | [ pos ] | [ tarpos ] | [ curmove ] | [ lastmove ] | [ sensor ] | [ gain ] | [ all ]
smc < name > queryr [ vel ] | [ accel ] | [ micro ] | [ vmax ] | [ distance ] | [ pos ] | [ tarpos ] | [ curmove ] | [ lastmove ] | [ sensor ] | [ stepsperunit ] | [ gain ] | [ all ]
smc < name > run < velocity >
smc < name > runr < velocity >
smc < name > sensor
smc < name > sensor < sensorMask >
smc < name > sensorinv
smc < name > sensorinv < sensorInvMask >
smc < name > start < quarter | half | full > [ [ < timeout > ] [ < zero | quarter | half | full > ] ]
smc < name > status
smc < name > stepsperunit
smc < name > stepsperunit < stepsPerRealUnit >
smc < name > stop [ now ]
smc < name > traj < address >
smc < name > traj < address > < acceleration > < steps >
smc < name > traj reset [ zero ]
smc < name > trajr < address >
smc < name > trajr < address > < acceleration > < distance >
smc < name > trajr reset [ zero ]
smc < name > udlast < lastValid >
smc < name > udvel < velocity >
smc < name > udvelr < velocity >
smc < name > unreserve
smc cafault [ < on | off > ]
spot < pixel offset > [ [ < pixel width > ] ]
spot < pixel offset > [ [ < pixel width > ] ]
spot full
spot off
stats
stats
stats < enable | disable >
status
status
status < groupname >
status < groupnumber >
status all
status scantime
statuslights
statuslights < blue | bluef | green | greenf | yellowf | off >
stg
stg
stg
stg delete flash < key >
stg delete ram < key >
stg delete temp < key >
stg erase flash
stg erase ram
stg erase temp
stg list flash
stg list ram
stg list temp
stg load
stg optimize flash
stg optimize ram
stg optimize temp
stg read flash < key >
stg read ram < key >
stg read temp < key >
stg status flash
stg status ram
stg status temp
stg verify flash
stg verify ram
stg verify temp
stg write flash < key > < data > +
stg write ram < key > < data > +
stg write temp < key > < data > +
stroke
stroke
stroke < pixel pair >
stroke < pixel pair > < stroke value >
stroke cal
stroke config
stroke init [ < stroke value > ]
stroke profile
stroke save
suspend
suspend
suspend add < error_code > [ [ < type > ] [ < buttons > ] ]
suspend buttons
suspend debug
suspend remove < suspend_id >
system
system
table
table < up | down | dn > [ w ]
table away
table cancel
table cups < up | down | dn > [ w ]
table fail
table fail < string >
table home
table idle
table init
table jog < distance >
table move < position > [ [ < velocity > ] ]
table move away
table move home
table move rotate
table push < on | off > [ w ]
table release
table rot < on | off > [ w ]
table search rotate
table step
table step < enable | disable >
table time
table vac < on | off > [ w ]
tac [ < on | off > [ < rpm > ] ]
tac [ < on | off > [ < rpm > ] ]
tec
tec
tec < lock | unlock > [ w ]
tec < lock | unlock > [ w ]
tec < on | off > [ w ]
tec < on | off > [ w ]
tec getclamp
tec getclamp
tec init
tec init
tec putclamp
tec putclamp
temp
temp
th2
th2
th2 < string >
tsp
tsp
tsp < channel >
tsp < channel > < enable | disable >
tsp < channel > clear
tsp pesel < enable | disable >
tsp scanlines < number >
tsp start
tsp test [ < subscan > ] [ < tsps > ] [ < mainscan > ]
tud
tud
tud create [ < period > ] [ < command > + ]
tud delete < number >
tud delete all
u
u
ui
ui
ui buzzer < on | off >
ui buzzer < on | off >
ui errlamp < on | off >
ui errlamp < on | off >
ui imglamp < on | off >
ui imglamp < on | off >
ui loadlamp < on | off >
ui loadlamp < on | off >
unload [ info ] | [ args ] | [ m ] [ < mlength > ]
unload [ info ] | [ args ] | [ m ] [ < mlength > ]
urt
urt
urt
urt break clear < port >
urt break reset < port >
urt break set < port >
urt break status < port >
urt close < port >
urt diag < port >
urt flush receive < port >
urt flush transmit < port >
urt handshake set < port > < data >
urt handshake status < port >
urt open < port > [ [ < baud > ] ]
urt receive < port > < count >
urt reset < port >
urt Rx < port >
urt transmit < port > < data > +
urt Tx < port >
vbs [ < token > + ]
vbs [ < token > + ]
verbose
verbose
verbose < level > < ss_name > +
verbose < level > all
verbose alpha
verbose default
verbose diag
verbose off
verbose off < ss_name > +
verbose off < ss_number > +
verbose off all
verbose on
verbose on < ss_name > +
verbose on < ss_number > +
verbose on all
verbose user
verbose user < level >
version [ < on | off > ]
version [ < on | off > ]
wb < address > < data >
wb < address > < data >
wl < address > < data >
wl < address > < data >
wmd
wmd cmd < code > < enable | disable >
wmd cmd < code > [
wmd cmd all < enable | disable >
wmd diag
wmd diag < enable | disable >
wmd diag cmd
wmd diag cmd < enable | disable >
wmd diag resp
wmd diag resp < enable | disable >
wmd diag uerr
wmd diag uerr < enable | disable >
wmd diag umsg
wmd diag umsg < enable | disable >
wmd listcmd
wmd promptinfo
wmd uerr < code >
wmd umsg
wmd umsg < enable | disable >
ww < address > < data >
ww < address > < data >
zdrive
zdrive debug
zdrive focus [ < diam > [ < mthick > ] | [ < offset > ] | [ c ] | [ calibrate ] ]
zdrive focus sample
zdrive focus stop
zdrive focus update
zdrive home
zdrive idle
zdrive init
zdrive jog < offset > [ [ < speed > ] | [ s ] ]
zdrive moveto < position > [ [ < speed > ] | [ s ] ]
zdrive sim [ < enable | disable > ]
zdrive stop
zstage
zstage back
zstage forward

    Copyright © 2005 Creo Inc. All rights reserved. Confidential. Back to top.