MPE Assemblies

Serial numbers start with TN

Note: Check SAP for latest BOMs.

Top level assemblies

Top level assemblies

Trendsetter NEWS—02-4289
Drawing not available | BOM

Kit, TS8 to TS2637 AL—50-2124a
Drawing not available |kit upgrade ts8 to ts2637

Common parts kit—11-0845
Drawing not available |BOM

TS Base kit—11-0846
Drawing not available |BOM

Preloader interface - for NEWS 150, 200 only

Preloader interface, MPE—11-1139A
Drawing not available |BOM

NELA preloader interface-11-1063A BOM
Preloader interface board-10-5072A

Preloader interface, MCE—11-1140A
Drawing not available |BOM

NELA preloader interface-11-1063A BOM
Preloader interface board-10-5072A

TS-A, Non-Rotator Autoloader kit—11-0817
Drawing not available |BOM

See Autoloader Assemblies for detail

Blanking panel assembly—50-1947
Drawing not available |BOM

Fly-off sensor
Transmitter—36-3117
Receiver—36-3118
Cable assembly—10-3612A

Head

50-2149A—Upgrade Kit 1.7 to 2.0
BOM

10-4954A—Power Cable to Thermal Head 2 (EH2-PWR)
Assembly drawing

10-4956A—Control Cable to Thermal Head 2 (TEH2-CTRL)
Assembly drawing

10-5145A—Hot link cable for Thermal 2 head (EH2 - BLKHD)

Autoloader assemblies

Load Ramp  
50-2426A  Assembly Drawing | BOM

Lower ramp cylinder, home 50-1653A Drawing|BOM
Upper ramp cylinder, home or away (FRU) 512-00263A - kit contains 2 cylinders plus all fittings Drawing - see FCO CA06235
Plate sensor 36-3219
Plate sensor to TEE cable 10-3687A Assembly Drawing
Nylon spacers 52-3323 - 5 pieces home side, 6 pieces away side photo
Spacers should not be too tight—allow 1 mm of movement after spacers installed.

Load Table
50-2425 Assembly Drawing | BOM

Plate ledge assembly 50-2459
Assembly Drawing | BOM
Note: if this is not the plate ledge you have, order upgrade kit 05-0241

Plate ledge flathead screws—52-7177

Plate sensor 36-3210

Picker vacuum generator 340-00001
Order kit 518-00114A to replace failed vacuum generator (340-00001 or 55-0632) or muffler (55-0569).

Door lock solenoid 10-3739A
Door lock relay 10-3800B

Operator door, Gas strut cylinder 330-00080 see CA04191

Warning light bulbs 36-3156 (part of assy 10-3742A)

Cables
Separator arms microswitch 10-3686A Assembly Drawing
Cover lock disconnect (runs inside load table) 10-3794A Assembly Drawing
Cover lock relay 10-3800B Assembly Drawing
Corner lights 10-3741A Assembly Drawing

Load table support bracket - 57-5450A

Manifold
50-2466A Assembly Drawing | BOM

Valve, Single Solenoid—55-0088
Valve, Double Solenoid—55-0089

Operator Door and Skins
50-1992A Operator Door Assembly Drawing | BOM
50-1931A Lower Operator Door
50-1973A Panel Kit TS8 AL BOM

Operator Interface
50-1522B Assembly Drawing | BOM

Board 10-1420B Assembly Drawing
Cable 10-3187B Assembly Drawing
Pushbutton switch 15-3246

Picker, Version III
50-2423 Assembly Drawing | BOM

Picker Head Assembly
50-2424 DWG | BOM

Picker head in/out cylinder kit 518-01238A - includes 2 cylinders and 2 elbows
cylinders on both sides should be replaced
Picker wrist cylinder 330-00002 see FCO CA00567 Wrist Cylinder Upgrade
Suction cups W\O valve, silicone, red 55-0706
Vacuum Generator 340-00001
Order kit 518-00114A to replace failed vacuum generator (340-00001 or 55-0632) or muffler (55-0569).
Wrist sensor cable assembly 10-4579A

Picker move up/down cylinders
Right 50-1761A Assembly | BOM
Left 50-1762A Assembly | BOM
   55-0804 (cylinder only)
Picker move sensor cable assembly 10-4071A (on Load table BOM)

Picker rails
Right 50-1763B Assembly | BOM
Left 50-1764A Assembly | BOM

Picker up/down sensors cable assembly 10-4651A drawing
Rail only - Order 57-6019B If you are replacing 57-6019A, the hole for attaching the bottom sensor is lower because of the change introduced in CA07202 - remove the foam on the side of the picker head (away position) so that the sensor will work.
Optical sensors on rails - Order kit 518-02218A (FCO CA11580) to replace 10-3676A. If FCO is already applied, order 500-03817A for replacement.
Picker rail bottom bracket 57-6000A (item 30 on 50-1763B and 50-1764A drawings

Picker guide cable (Stainless steel) 50-1765A See also FCO E042.

Lower pulley for guide cable (Picker 3) 57-6015A Drawing
Pulley 1, Move Cylinder (Larger upper pulley for Picker 3) 57-6016A Drawing
Pulley 2, Move Cylinder (Small upper pulley for Picker 3) 57-6017A Drawing
Bushing,1/4"*5/16"*1/2",Bronze 54-4024

Miscellaneous
Speed ctrl 0.1mm orfice 55-0807
Speed ctrl 0.2mm orfice 55-0806

Sensor reed switch 15-3063
Magnet for reed switch 59-3141

Unload Pans
Short pan 50-2427A Assembly Drawing | BOM

Traveler 50-2428 BOM
Flex track 10-3773D See E876

Idler pulley 50-1497A
Motor Assembly 50-1496A Assembly Drawing | BOM
        Motor only 15-3234
        Drive pulley 50-1756A
        Rubber spider in coupling between pulley and motor 50-0231
Plate eject sensor 36-3141
Suction Cup 55-0541
Traveler home/away optical sensor 10-3683

Short bridge 50-1617A Assembly Drawing | BOM

Unload Table 50-1449A
Assembly Drawing | BOM
Note: for older versions, see Parts Archive

Unload cylinder 50-1493A Assembly Drawing |BOM

• Cylinder only 55-0604
• Orifice for non-rotator table 55-1188 Drawing item 20
• Orifice for rotator table 55-1187 Drawing item 20

Clevis and Pin Kit 50-2341A FCO E100
Kit includes:

• 52-4488 Cotter pin, auto locking, 1/2" shaft (2)
• 52-4064 M12 washer (4)
• 52-4897 Clevis pin, 7/16"*2.5" (2)
• 55-0605 Rod end, clevis, 5/8" - 18, 0.43 Pin (2)

Traveler drive motor controller board 15-3235

Plate pusher 50-1690 Assembly Drawing |BOM

Safety guard 57-5245

Rear cover panel 50-1535A Assembly Drawing

Cables
Sensors to TEE (J6) 10-3682A Assembly Drawing

Base Machine

Carriage

Carriage motor and Pulley—11-0865
Assembly Drawing| BOM

Carriage motor cooling assembly—11-0885
Assembly Drawing | BOM
( fan #10-4521A)

Carriage motor mount—50-1623
Drawing not available | BOM

Carriage Adapter Plate (TEH 1.7 to 2.0)—50-2476
Assembly Drawing |

Engine

Engine—50-2109
Assembly Drawing | Pneumatic Circuit Schematic | BOM

• Edge detect strips  57-3826
• High registration blocks  57-7514 see Assembly Drawing
• Low registration blocks 57-7515
• Center leading edge clamp pivot block (1 required) 57-7745
  (This block fits into the groove for the registration pin)
• LEC Pivot block ends (2 required) 57-7698
• LEC pivot block central (4 required) 57-6851