| DIO | |
| ld (<diode>|all) (on|off) | Turn diode(s) on/off. |
| ld (<diode>|all) <current> ma | Set diode current(s). |
| ld (<diode>|all) mask (on|off) | Enable/disable diode masking. |
| ld zero | Turn off all diodes, zero the currents. |
| ld [<diode>] | Show the status of the diode(s). |
| safe [exit] | Enter of exit safe (currents off) mode. |
| DOT | |
| ontime [e] | Display the diode odometer. |
| DPC | |
| ld (<diode>|all) <power> mw | Set diode powers. |
| report | Report on the health of diodes. |
| DPS | |
| dps raw [<samples>] | Get raw values from power sensor. |
| dps response <diode> <samples> [<power>] | Measure the time response of a diode. |
| ld <diode> read | Measure a diode's power. |
| ld all read [<ms_delay>] | Measure the power of all diodes. |
| DSC | |
| analyze [<medIndex>] [e] | Analyze the accuracy of a media strokes. |
| cal | Do a full power calibration. |
| cal abort | Abort an ongoing calibration. |
| cal status | Show the status of an ongoing calibration. |
| dsc hotlink reset | Resets the hotlink error counter. |
| ld stroke | Set diodes to the stroke of the current media. |
| EED | |
| eeprom erase | Erase the EEPROM. |
| eeprom info | Display EEPROM information. |
| eeprom verify | Verify the EEPROM. |
| ERR | |
| err <code> | Print the error code. |
| err list | List all registered error codes. |
| FLS | |
| fls info | Display flash information. |
| FOC | |
| foc (on|on init|off) | |
| foc actmode [<actuator mode>] | |
| foc cal reflect | |
| foc info | |
| foc lpos [<lens position>] |
| HDW | |
| reset [soft] | Perform a hardware / software reset. |
| HIF | |
| laser (on|off) | Configure the write laser control mode. |
| shutter (open|close) | Open / close the internal shutter. |
| stroke cal | Perform a stroke calibration. |
| MED | |
| med index <media index> | Select the media. |
| med info | Display media information. |
| MON | |
| (field|eng) | Set the access level. |
| help list | List all registered subsystems. |
| help [<subsystem>] | List registered commands. |
| monitor baud (9600|19200|38400|57600|115200) | Change the monitor baud rate. |
| PRF | |
| parm receive | Receive parameter file and restore the parameters. |
| parm receive <subsystem> | Receive parameter file, restore a subsystem. |
| parm send | Send parameter file to the PC host. |
| PRM | |
| prm copy <subsystem> [<parameter>] <source> <destination> | Transfer all subsystem parameters. |
| prm diff | List the baseline parameters. |
| prm dump | Dump all parameters. |
| prm list | List all registered subsystems. |
| prm restore | Restore the baseline parameters. |
| prm save | Save the baseline parameters. |
| set | List all registered subsystems. |
| set <subsystem> [<copy>] <parameter> [(<element>|all)] <value> | Write the parameter. |
| set <subsystem> [<copy>] [<parameter>] | Read the parameter. |
| RDR | |
| redirect (enable|pass|disable) | Configure the redirection mode. |
| redirect info | Display redirection information. |
| REG | |
| reg erase [baseline] | Erase the registry. |
| reg info | Display registry information. |
| reg optimize | Optimize the registry. |
| reg verify [baseline] | Verify the registry. |
| SBT | |
| fload bundle | Load the firmware bundle ( binary download ). |
| fload bundle y | Load the firmware bundle ( Y-modem download ). |
| SYM | |
| temp | Read all temperatures from the system monitor. |
| volt | Read all voltages from the system monitor. |
| SYS | |
| coldplot (on|off) | Plot without power to the diodes. |
| hold delay (on|off) | Hold the temporary diode pixel delays. |
| hold focus (on|off) | Hold the focus values. |
| hold mask (on|off) | Hold the diode plot mask. |
| hold power (on|off) | Hold manually set diode powers. |
| ignore focus (on|off) | Ignore focus commands. |
| ignore params (on|off) | Ignore MPE parameters. |
| sys fault (warning|fatal) [<number>] | Generate warning / fatal fault(s). |
| sys fault state | Determine the fault state. |
| sys fault [<point> (on|off)] | Display / configure the fault configuration. |
| sys info | Display system plot settings. |
| sys parm access <index> (disable|enable) | Configure host access to the system parameters. |
| sys parm config | Configure the system parameters. |
| sys parm [<index> <value>] | Display / write the system parameters. |
| URT | |
| urt info | Display uart information. |
| VBS | |
| vbs disable (<subsystem>|all) | Disable the verbose level for the subsystem(s). |
| vbs enable (<subsystem>|all) <level> | Enable the verbose level for the subsystem(s). |
| vbs list | List the verbose level for all subsystems. |
| VER | |
| ver | Display the firmware banner. |
| ver list | List all registered subsystems. |