| bbs maximumerror | Configure the maximum allowable beam-balance error. |
| bpd ab | The input weighting of the proportional gain for the PID controller for laser A. |
| bpd aki | The integral gain for the PID controller for laser A. |
| bpd akp | The proportional gain for the PID controller for laser A. |
| bpd ascendoffseta | The ascending offset for the "A" beam-pointing actuator. |
| bpd ascendoffsetb | The ascending offset for the "B" beam-pointing actuator. |
| bpd ascendslopea | The ascending slope for the "A" beam-pointing actuator. |
| bpd ascendslopeb | The ascending slope for the "B" beam-pointing actuator. |
| bpd b | The input weighting of the proportional gain for the PID controller for the centroid. |
| bpd bb | The input weighting of the proportional gain for the PID controller for laser B. |
| bpd bki | The integral gain for the PID controller for laser B. |
| bpd bkp | The proportional gain for the PID controller for laser B. |
| bpd dbpsconfig | The differential beam-pointing sensor configuration. |
| bpd descendoffseta | The descending offset for the "A" beam-pointing actuator. |
| bpd descendoffsetb | The descending offset for the "B" beam-pointing actuator. |
| bpd descendslopea | The descending slope for the "A" beam-pointing actuator. |
| bpd descendslopeb | The descending slope for the "B" beam-pointing actuator. |
| bpd diffcal | The calibration factor for the differential beam-pointing sensor. |
| bpd doffset | The differential offset for the for the beam-pointing control loop. |
| bpd ki | The integral gain for the PID controller for the centroid. |
| bpd kp | The proportional gain for the PID controller for the centroid. |
| bpd offset | The position offset for the beam-pointing control loop. |
| bpd psdoffset | The PSD offset for the PSD sensor. |
| bpd sensormode | The sensor mode of the beam-pointing driver. |
| bpd xtalkab | A crosstalk co-efficient for the differential beam-pointing sensor. |
| bpd xtalkba | A crosstalk co-efficient for the differential beam-pointing sensor. |
| bpd xtalkdira | A crosstalk co-efficient for the differential beam-pointing sensor. |
| bpd xtalkdirb | A crosstalk co-efficient for the differential beam-pointing sensor. |
| foc Bandwidth | Closed-loop position servo bandwidth |
| foc CurrentLimit | Current limit of voice coil lens tube actuator |
| foc DmodSync | Focus laser demodulator delay |
| foc ForceConstant | Actuator Force Constant |
| foc LaserFreq | Focus laser frequency |
| foc lpos | Focus lens position in 'fixed' mode |
| foc Offset | Focus offset in microns |
| foc PayloadMass | Mass of lens tube assembly |
| foc PositionSensitivity | LVDT position sensitivity |
| foc TransmitGain | focus laser power gain to compensate for transmissivity |
| h1c brt | Delay required before initiating a beam-balance. |
| h1c lrt | Delay required before launching the first image. |
| h1c sssa | Component of sub-scan shift adjust dependent on the exposure head. |
| ibs maximumerror | Configure the maximum allowable internal balance error. |
| med <media index> beamcurve <polarity> | The target curve for the beam-balance. |
| med <media index> beampiston | Link the target profiles for the beam-balance. |
| med <media index> beamslope <polarity> | The target slope for the beam-balance. |
| med <media index> colour | The media colour for identifying media. |
| med <media index> drumspeed | The drum speed for the media. |
| med <media index> focusmode | The focus mode for the media. |
| med <media index> focuspower | The focus laser power reaching the surface the media. |
| med <media index> imagemode | The image mode for identifying media. |
| med <media index> laserpower | The write laser power for the media. |
| med <media index> name | The media name for identifying media. |
| med <media index> rcvrgain | The receiver gain of the media. |
| med <media index> scorr <polarity / spot quad> | The stroke correction table for the media. |
| med <media index> sd | The surface depth of the media. |
| med <media index> sensitivity | The sensitivity for the media. |
| med <media index> sensitivityadjust | The sensitivity adjustment for the media. |
| med <media index> stroke <polarity / spot quad> | The stroke table for the media. |
| med <media index> strokeoffset | Configure the pixels used for plotting. |
| med <media index> strokewidth | Configure the pixels used for plotting. |
| med <media index> surfacevelocity | The surface velocity for the media. |
| sys annealaccrual | The accrual time for the light valve annealing. |
| sys annealsetpoint | The setpoint time for light valve annealing. |
| sys comment | A comment that applies to the exposure head. |
| sys dpi | The maximum DPI of the exposure head. |
| sys imagedata | Configure the source for the image data. |
| sys imagetiming | Configure the source for the image timing. |
| sys laseranneal | Enable / disable the light valve annealing. |
| sys laserenable | Enable / disable the write laser. |
| sys laserstandby | Enable / disable the write laser standby. |
| sys plotenable | Enable / disable plotting. |
| sys polarity | Configure the polarity type. |
| sys ratedpower | The rated power for the exposure head ( at full stroke width ). |
| sys serialnumber | The serial number of the exposure head. |
| sys standbyperiod | The period for the write laser standby. |
| sys standbythreshold | The threshold for the write laser standby. |
| sys standbytimeout | The timeout for the write laser standby. |
| sys tpgpattern | Configure the TPG pattern. |