The Magnus 800 Platesetter (S, F, V, X, Z-speed) Safety Guide for Operators has been translated into: Simplified Chinese, Traditional Chinese, Czech, Danish, Dutch, Estonian, Finnish, French, German, Greek, Hungarian, Italian, Japanese, Korean, Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovakian, Slovenian, Swedish,and Turkish. Go to the Safety page.

Go to Site preparation on the Installation page.

When customers use plates ranging from 0.15 mm to 0.3 mm, and experience edge detection problems and/or focus learn errors, zero the head for 0.3 mm plates, so that the error will be +50 µ when the z-stage is in its back position. This software issue will be resolved with the release of Magnus 800 Controller software version 1.06.406. Go to Software on the Troubleshooting page.

Go to Multi-directional unloading conveyor on the Procedure page.

Order the loading platform shaft and bearing kit (514-00165A). Go to Loading platform on the Troubleshooting page.

Go to the Safety page.

Implement FCO 512-00475A to replace the existing TEC actuator bracket with an improved, stronger bracket. Find this item under Unloading process on the FCOs page.

Go to the Safety page.

To learn about punches, and how to order and install them according to customer requirements, see the CTP Punching presentation.
Go to Training on the Reference page.

The Turbo Screening Processor (TSP) board is highly sensitive to electro-static discharge (ESD). Therefore, disconnect the electricity leading to the platesetter and the Brisque workstation, before disconnecting the TSP data cable. Go to Maintenance on the Procedure page.

If you try to connect a cable when the pins are not properly aligned, you may damage the connector and the pins. This can cause intermittent communication, lvd data, or safety loop errors.

The military connectors should sit easily and evenly. If this is not the case, do not force the connector.

If you suspect that the pins are damaged, go to Intermittent communication, lvd data, or safety loop errors.

Go to Installation procedures on the Installation page.

Go to Connectivity procedures on the Connectivity page.

Go to Settings on the Control/settings page.

Replace the existing platesetter MSB motherboard with the improved MSB motherboard (503-00514A). The improved MSB motherboard has electrostatic discharge (ESD) protection. Go to FCO 512-00486A under Boards on the FCO page.

Go to the Installation page.

This procedure describes how to use the Magnus Output Devices Installation Report Tool. The tool enables field engineers to provide installation feedback to Kodak. After every installation, open the Magnus Output Devices Installation Report Tool and submit the report.
Go to the Installation page.

The Magnus 800 Platesetter S300 Safety Precautions for Operators has been translated into: Greek, Hungarian, Korean, Latvian, Lithuanian, Russian, Slovenian, and Turkish. Go to the Safety page.

Go to Replacing the thermal 3 head air filters on a Magnus 800 platesetter on the Maintenance page.

Go to Installing a variable punch on Magnus 800 platesetter on the Procedures page.

Go to Installing Kit 514-00164A onto a Magnus 800 platesetter to enable support for 12-inch plates on the Procedures page.

Go to Lenticular printing on the Reference page.

Go to Lenticular printing on the Procedures page.

To avoid MCE connectivity problems on Magnus 800 platesetters, replace the SCSI board.
Go to Connectivity on the Troubleshooting page.

The Magnus 800 Platesetter S300 Safety Precautions for Users has been translated into: Simplified Chinese, Traditional Chinese, Danish, Estonian, Finnish, Japanese, Norwegian, and Swedish. Go to the Safety page.

Replace the existing safety cables with improved safety cables. The improved safety cables have larger grommets than their predecessors, leading to a reduction in friction between the safety cables and the loading platform actuator brackets. Go to 512-00449A under Loading process on the FCO page.

Go to the Reference page.

Go to Connecting an InterPlater 85/135 HD processor to a Magnus 800 platesetter on the Installation page.

This troubleshooting document describes how to insert clips onto the unloading platform axle, in order to prevent the unloading platform from moving sideways. This document is only applicable to platesetters with serial numbers M80300-M80320. Go to Preventing the unloading platform from moving sideways on the Troubleshooting page.

The Magnus 800 platesetter installation guide has been updated to reflect the recently added Lenovo computer. Find the updated Magnus 800 Platesetter Installation Guide on the Installation page.

The ISO image (.iso) is located on a dedicated server, offering very fast download times. Download the ISO image of Microsoft Windows Server 2003 - server image for Magnus 800 Lenovo M55e V1.12 (1.2 GB) from the Software section on the Downloads page.

The ISO image (.iso) is located on a dedicated server, offering very fast download times. Download the ISO image (.iso) of Microsoft Windows Server 2003 - server image for Magnus 800 IBM x206/x206m V1.09 (1.2 GB) from the Software section on the Downloads page.

The ISO image (.iso) is located on a dedicated server, offering very fast download times. Download the ISO image (.iso) of Magnus 800 controlled release, software version 1.04.404 (230 MB) from the Software section on the Downloads page.

The ISO image (.iso) is located on a dedicated server, offering very fast download times. Download the ISO image (.iso) of Magnus 800 controlled release, software version 1.05.405 (230 MB) from the Software section on the Downloads page.

This procedure describes how to install a thermal 1.7 head (TH 1.7) on a Magnus 800 platesetter. Go to the Installation page.

The Magnus 800 Platesetter S300 Safety Precautions for Users has been translated into the following languages: Magnus 800 platesetter safety guide for operators (Czech), Magnus 800 platesetter safety guide for operators (Dutch), Magnus 800 platesetter safety guide for operators (French), Magnus 800 platesetter safety guide for operators (German), Magnus 800 platesetter safety guide for operators (Italian), Magnus 800 platesetter safety guide for operators (Polish), Magnus 800 platesetter safety guide for operators (Portuguese), and Magnus 800 platesetter S300 safety precautions for users (Slovakian). Go to the Safety page.

Imaging artifacts may be resolved by replacing the carriage with a carriage that was modified to accept 30 mm radial roller bearings. The new bearings help ensure uniform movement along the carriage tracks. Go to 512-00424A under Optomech on the FCO page.

This guide describes the loading sequence and parameters for the Magnus 800 platesetter. Go to Sequence and parameter reference guide for the Magnus 800 platesetter under Loading sequence on the Reference page.

Files Collector 2.0 is a utility that collects log files and registry paths from the Magnus 800 platesetter and sends them to a Kodak FTP server. Find the Files Collector 2.0 utility and the Files Collector 2.0 user guide under Utilities on the Downloads page.

This troubleshooting document describes how to prevent the diagnostic software from failing at the saw tooth test, which is part of the MSB test. Find this item under Software on the Troubleshooting page.

This document describes how to install a ZOOM PCI analog modem on a Magnus 800 computer. The Zoom V.92 PCI 56K internal analog modem on the Magnus 800 computer is used to support the platesetter from a remote location. The modem is only to be used if a fast connection and/or a modem on the workflow device is unavailable. Find this procedure under Remote installation and setup procedures on the Installation page.

The ZOOM PCI analog modem driver is available for downloading. Find this item under Drivers on the Installation page.

Find the Magnus 800 platesetter safety guide for service engineers on the Safety page.

The Magnus 800 Controller software version information page has been updated to reflect the recommended software that can be installed along with Magnus 800 Controller, Controlled Release, Software Version 1.05.405.101. Find this item under Software information the Reference page.

This document describes how to back up and restore the Magnus 800 computer's drives. Find this item under Software on the Procedures page.

The Magnus 800 Series 300 Delta Course Internal Self-Study Guide is now available on TechPlanet. Find this item under Training on the Reference page.

Find the Magnus 800 platesetter safety guide for operators on the Safety page.

The latest release notes for Magnus 800 Controller software, version 1.05.405.101 are located under Release Notes on the Reference page.

This reference document describes how to diagnose the Magnus 800 platesetter software. Find this item under Software information on the Reference page.

This troubleshooting document describes how to prevent abrasive damage to the unloading platform motor wiring harness. Find this item under Unloading platform on the Troubleshooting page.

This procedure describes how to connect a Mercury V6 processor to a Magnus 800 platesetter. Find this item under Installation procedures on the Installation page.

This troubleshooting document describes how to resolve intermittent alignment system failures. Find this item under Plates on the Troubleshooting page.

The latest release notes for Magnus 800 Controller software, version 1.04.404.059 are located under Release Notes on the Reference page.

The updated version of the Magnus 800 Platesetter Installation Guide includes a section describing how to configure the parameters for additional modules. Find this guide under Installation procedures on the Installation page.

Implement FCO 512-00363A to incorporate new software features and to eliminate problems that appeared in earlier versions of the software. Find this item under Software on the FCOs page.

This troubleshooting document describes how to interpret the behavior of the LEDs on the Magnus 800 MSB. Find this item under Electronics on the Troubleshooting page.