The Magnus 800 Lenovo M55e document provides information about the Magnus 800 Lenovo M55e computer, such as warranty coverage, support numbers, and escalation procedures. Find this item under Connectivity procedures on the Connectivity page.

This procedure describes how to replace the leading edge clamp (LEC) on a Magnus 800 platesetter. Find this item under Optomech on the Procedures page.

This procedure describes how to relocate a registration pin on a Magnus 800 platesetter. Find this item under Optomech on the Procedures page.

This procedure describes how to configure and define punches on a Magnus 800 platesetter. Find this item under Loading platform on the Procedures page.

The Web-based version of the Magnus 800 Component Finder Utility is a browser enabled, searchable database containing all the Magnus 800 components. Find this utility under Component finder on the Reference page.

Implement FCO 512-00415A to lower the unloading platform; increase the gap between the unloading platform and the TEC beam, and thus prevent plates from becoming scratched. Find this item under Unloading process on the FCOs page.

This updated procedure describes how to assemble and install the Magnus 800 unloading conveyor. Find this item under Installation Procedures on the Installation page.

This procedure describes how to upgrade the Magnus 800 platesetter and autoloader MSB firmware. Find this item under Software on the Procedures page.

The Magnus 800 Component Finder Utility is a stand-alone, searchable database containing all the Magnus 800 components. The utility and download instructions are both located on the Downloads page.

Find these items under Wiring schematics on the Parts/tools page.

This procedure describes how to connect a Kodak CPG-86/125 processor to a Magnus 800 platesetter. Find this item under Installation procedures on the Installation page.

This procedure describes how to use the Files Collector utility. The Files Collector utility collects data required for analyzing a problem with the device, and sends the information to a Kodak FTP server. The collected data is used for troubleshooting the device. Find this item under Software procedures on the Procedures page.

The Ghost Backup and Restore Utility backs up and restores a ghost image of the previous C drive or the entire disk. Download this utility from the Utilities section on the Downloads page.

This procedure describes how to adjust the dynamic balance weights on the Magnus 800 platesetter. Find this item under Optomech procedures on the Procedures page.

This procedure describes how to align the TEC actuator mushroom pin to the TEC keyhole. If the TEC actuator mushroom pin and the TEC keyhole are not correctly aligned, the TEC actuator may fail to lift the TECs from the drum, and the TECs may be irreparably damaged. Find this item under Optomech procedures on the Procedures page.

This procedure describes how to adjust the position of the platesetter drum in order to optimize the LEC opening. Find this item under Optomech procedures on the Procedures page.

This procedure describes how to calibrate the drum motor encoder on the Magnus 800 platesetter. Find this item under Optomech procedures on the Procedures page.

This procedure describes how to activate the optic sensor on a third-party unloading conveyor. Find this item under Installation procedures on the Installation page.

This document describes how to repair immobile TEC bodies to prevent them from becoming unusable. Find this item under Drum assembly on the Troubleshooting page.

This procedure describes how to use Service Shell to download firmware onto the turbo master electronics board. Find this item under Software on the Procedures page.

This procedure describes how to use Service Shell to restore previously saved parameters onto the turbo master electronics board. Find this item under Software on the Procedures page.

This procedure describes how to use Service Shell to backup the turbo master electronics board. Find this item under Software on the Procedures page.

This document describes how to resolve retry process failures by amending the values of the relevant speed and timeout parameters. Find this item under Plates on the Troubleshooting page.

This document describes how to resolve loading problems associated to large plates. Find this item under Plates on the Troubleshooting page.

The Magnus 800 Platesetter Safety Precautions for Users has been translated into the following languages: Magnus 800 Platesetter Safety Precautions for Users (Czech), Magnus 800 Platesetter Safety Precautions for Users (Danish), Magnus 800 Platesetter Safety Precautions for Users (Estonian), Magnus 800 Platesetter Safety Precautions for Users (Finnish), Magnus 800 Platesetter Safety Precautions for Users (Greek) , Magnus 800 Platesetter Safety Precautions for Users (Hungarian), Magnus 800 Platesetter Safety Precautions for Users (Latvian), Magnus 800 Platesetter Safety Precautions for Users (Lithuanian), Magnus 800 Platesetter Safety Precautions for Users (Norwegian), Magnus 800 Platesetter Safety Precautions for Users (Polish), Magnus 800 Platesetter Safety Precautions for Users (Russian), Magnus 800 Platesetter Safety Precautions for Users (Slovakian), Magnus 800 Platesetter Safety Precautions for Users (Slovenian), Magnus 800 Platesetter Safety Precautions for Users (Swedish), and Magnus 800 Platesetter Safety Precautions for Users (Turkish). Find these documents on the Safety page.

This procedure describes how to make sure the TEC actuator beam is at the correct height in relation to the drum. Find this item under Optomech on the Procedures page.

This document describes the parameter value ranges for the Magnus 800 platesetter. Find this item under Settings on the Control/settings page.

This procedure describes how to adjust the height of the Magnus 800 loading platform in relation to the static loading tray, alignment system, and drum position. Find this procedure under Loading platform on the Procedures page.

This procedure describes how to upgrade the speed of a Magnus 800. Find this item under Upgrade on the Procedures page.

A revised and more concise version of the Magnus 800 platesetter installation guide has been posted on TechPlanet. Find this item under Installation procedures on the Installation page.

Implement FCO 512-00349A to eliminate problems that appeared in earlier versions of the software. Find this item under Software on the FCOs page.

The punch configurator utility contains all the information pertaining to a customer’s punch configuration. Find this item under Punch configurator on the Parts/tools page.

This document describes the latest, recommended software that can be installed with each new software release. Find this document under Software version information on the Reference page.

This document describes the improvements that were implemented on Magnus 800 devices between beta and early production. Find this document under Technical bulletins on the Reference page.

This procedure describes how to change the DHCP address of the Magnus 800 computer to enable laptop connectivity. Find this pdf document under Connectivity procedures on the Connectivity page.

This procedure describes how to set up the Magnus 800 computer to the customer's local network. Find this pdf document under Installation procedures on the Installation page.

The Magnus 800 Installation Test Procedure Checklist has been translated into the following languages: Simplified Chinese, French, German, Italian, and Spanish. Find these checklists under Installation procedures on the Installation page.

The installation program for Magnus Controller software version 1.02.402.004 contains a bug that erases the machine license. This troubleshooting document describes how to recover the machine license when installing Magnus Controller software version 1.02.402.004. Find this item under Software on the Troubleshooting page.

This procedure describes how to assemble and attach the unloading conveyor to the Magnus 800 platesetter and processor. Find this document under Plate picker system on the Installation page.

The Site Preparation Guide for Magnus 800 Output Devices has been translated into Japanese. Find this document under Site preparation on the Installation page.

The Magnus 800 Platesetter Safety Precautions for Users has been translated into Japanese. Find this document on the Safety page.

The Magnus 800 Platesetter Visual Reference Guide has been translated into the following languages: Simplified Chinese, French, German, Italian, Japanese, and Spanish. Find these guides under Visual reference guides on the Reference page.

The Magnus 800 Installation Test Procedure Checklist is now available on TechPlanet. Complete the installation test procedure checklist after performing all the test procedures described in the Magnus 800 ITP. Find the Magnus 800 installation test procedure checklist under Installation procedures on the Installation page.

The Magnus 800 self-study guides and internal course are now available on TechPlanet. Find these items under Training on the Reference page.

The Magnus 800 onsite training checklist helps confirm that your customer has acquired all the required knowledge regarding operating and maintaining the Magnus 800 device. Find this item under Installation procedures on the Installation page.

The Thermal plates page can be accessed directly from all the Magnus 800 sites. To access the Thermal plates page, click the Media link, located in the Related sites section of the navigation pane.

The Service Shell home page can now be accessed directly from the Magnus 800 site. The Service Shell link is located under Service tools on the Connectivity page.

The Installing a thermal 2 head on a Magnus 800 platesetter document is located under Optomech on the Procedures page.

This troubleshooting document describes how to check the screws securing the bypass keys, in order to prevent the safety loop from being intermittently activated on Magnus 800 devices. Find this item under Panels and doors on the Troubleshooting page.

The release notes for Magnus Controller software, version 1.02.402.004 are located under Release Notes on the Reference page.

The Magnus 800 Platesetter Safety Precautions for Users has been translated into the following languages: Dutch, French, German, Italian, Portuguese, and Spanish. Find these documents on the Safety page.

This troubleshooting document describes how to resolve the problem of Magnus Controller not starting when the JOIND Diagnostics software is running. Find this item under Software on the Troubleshooting page.

The Magnus 800 IBM Server (xSeries 206m) document provides information about the Magnus 800 IBM server, such as warranty coverage, support numbers, and escalation procedures. Find this item under Connectivity procedures on the Connectivity page.

Increased media sensitivity on V- and X-speed devices is normal. Check the CTP media database for the correct drum speed and estimated power setting, then refer to the media tech note for the detailed setup procedure.

For an example, see section 6.3 of the Kodak Thermal Gold Technical Note.

Download the latest CTP Media Imaging Performance Database. For more details on media qualification and settings, see the Media site.

This troubleshooting document describes how to release a stuck plate from the Magnus 800 punch and how to take preventive measures to avoid a repetition of the problem. Find this item under Plates on the Troubleshooting page.

Find the Chinese, French, German, Italian, and Spanish versions of the site preparation guide for Magnus 800 output devices under Site preparation on the Installation page.

The Verifying the position of the left - and right-side doors on the Magnus 800 platesetter procedure describes how to verify if the left- and right-side doors are correctly positioned. If the doors are incorrectly positioned, the safety switches will not function as required. Find this item under Panels and Doors on the Procedure page.

After installing a device, complete and return the Installation Feedback Report. The report is located under Installation procedures on the Installation page.

The Magnus 800 Platesetter Visual Reference Guide depicts basic operating procedures, troubleshooting, and operator maintenance. Find this item under Visual reference guides on the Reference page.

The Site Preparation Guide for Magnus 800 Output Devices is located under Site preparation on the Installation page.

The Product description and specifications for the Magnus 800 devices is located under Product description on the Overview page.

The Magnus 800 Internal Self-Study Guide for Early Production is located under Training, on the Reference page.

The zipped version of the Magnus 800 Platesetter Help is located under Online help, on the Reference page.

The technical bulletin, Using Magnus 800 Help with Flash 8 describes how to resolve the security issue with Flash Player 8. Find this item under Technical Bulletins, on the Reference page.