| ACT | |
| act blockeracceleration <index> | Configure the maximum acceleration for the beam-blockers. |
| act blockerhold <index> | Configure the hold time for the beam-blocker. |
| act blockerspeed <index> | Configure the maximum speed for the beam-blocker. |
| act shutteracceleration | Configure the maximum acceleration for the fast shutter. |
| act shutterhold | Configure the hold time for the fast shutter. |
| act shutteroffset | Configure the actuation offset for the fast shutter. |
| act shutterspeed | Configure the maximum speed for the fast shutter. |
| act shuttersteps | Configure the actuation steps for the fast shutter. |
| BBS | |
| bbs maximumerror | Configure the maximum allowable beam-balance error. |
| bbs powerfactor <index> | Calibration factors to convert samples to power. |
| BPD | |
| bpd ab | The input weighting of the proportional gain for the PID controller for laser A. |
| bpd aki | The integral gain for the PID controller for laser A. |
| bpd akp | The proportional gain for the PID controller for laser A. |
| bpd ascendoffseta | The ascending offset for the "A" beam-pointing actuator. |
| bpd ascendoffsetb | The ascending offset for the "B" beam-pointing actuator. |
| bpd ascendslopea | The ascending slope for the "A" beam-pointing actuator. |
| bpd ascendslopeb | The ascending slope for the "B" beam-pointing actuator. |
| bpd b | The input weighting of the proportional gain for the PID controller for the centroid. |
| bpd bb | The input weighting of the proportional gain for the PID controller for laser B. |
| bpd bki | The integral gain for the PID controller for laser B. |
| bpd bkp | The proportional gain for the PID controller for laser B. |
| bpd dbpsconfig | The differential beam-pointing sensor configuration. |
| bpd descendoffseta | The descending offset for the "A" beam-pointing actuator. |
| bpd descendoffsetb | The descending offset for the "B" beam-pointing actuator. |
| bpd descendslopea | The descending slope for the "A" beam-pointing actuator. |
| bpd descendslopeb | The descending slope for the "B" beam-pointing actuator. |
| bpd diffcal | The calibration factor for the differential beam-pointing sensor. |
| bpd doffset | The differential offset for the for the beam-pointing control loop. |
| bpd ki | The integral gain for the PID controller for the centroid. |
| bpd kp | The proportional gain for the PID controller for the centroid. |
| bpd offset | The position offset for the beam-pointing control loop. |
| bpd psdoffset | The PSD offset for the PSD sensor. |
| bpd sensormode | The sensor mode of the beam-pointing driver. |
| bpd xtalkab | A crosstalk co-efficient for the differential beam-pointing sensor. |
| bpd xtalkba | A crosstalk co-efficient for the differential beam-pointing sensor. |
| bpd xtalkdira | A crosstalk co-efficient for the differential beam-pointing sensor. |
| bpd xtalkdirb | A crosstalk co-efficient for the differential beam-pointing sensor. |
| EVT | |
| evt cachestate <index> | Configure the cache state. |
| FOC | |
| foc Bandwidth | Closed-loop position servo bandwidth |
| foc CurrentLimit | Current limit of voice coil lens tube actuator |
| foc DmodSync | Focus laser demodulator delay |
| foc ForceConstant | Actuator Force Constant |
| foc LaserFreq | Focus laser frequency |
| foc lpos | Focus lens position in 'fixed' mode |
| foc Offset | Focus offset in microns |
| foc PayloadMass | Mass of lens tube assembly |
| foc PositionSensitivity | LVDT position sensitivity |
| foc TransmitGain | focus laser power gain to compensate for transmissivity |
| HIF | |
| h1c brt | Delay required before initiating a beam-balance. |
| h1c lrt | Delay required before launching the first image. |
| h1c sssa | Component of sub-scan shift adjust dependent on the exposure head. |
| HLT | |
| hlt mask0 | The metric mask for metric points 0 to 31. |
| hlt mask1 | The metric mask for metric points 32 to 63. |
| hlt mask2 | The metric mask for metric points 64 to 95. |
| hlt mask3 | The metric mask for metric points 96 to 127. |
| hlt mask4 | The metric mask for metric points 128 to 159. |
| IBS | |
| ibs maximumerror | Configure the maximum allowable internal balance error. |
| LDD | |
| ldd cki | The integral gain for the PID controller for the calibration to the beam-balance sensor. |
| ldd ckp | The proportional gain for the PID controller for the calibration to the beam-balance sensor. |
| ldd drivemode | The drive mode of the laser diode driver. |
| ldd kb | The input weighting of the proportional gain for the PID controller for the laser diode sensor. |
| ldd ki | The integral gain for the PID controller for the laser diode sensor. |
| ldd kp | The proportional gain for the PID controller for the laser diode sensor. |
| ldd lasermode | The laser mode of the laser diode driver. |
| ldd laserontimea | The laser on time for laser diode A. |
| ldd laserontimeb | The laser on time for laser diode B. |
| ldd nominalcurrenta | The nominal current for laser diode A. |
| ldd nominalcurrentb | The nominal current for laser diode B. |
| ldd sensorcal | The sensor calibration for the laser diode sensor. |
| ldd slopeefficiencya | The slope efficiency for laser diode A. |
| ldd slopeefficiencyb | The slope efficiency for laser diode B. |
| ldd thresholdcurrenta | The threshold current for laser diode A. |
| ldd thresholdcurrentb | The threshold current for laser diode B. |
| LOG | |
| log delay | Configure the trigger delay. |
| log enable | Enable / disable the acquisition of plot data. |
| log plot <index> | Enable / disable the acquisition of plot data for the sample point. |
| log sample <index> | Enable / disable the acquisition of sample data for the sample point. |
| log trigger | Configure the trigger event. |
| LVD | |
| lvd blockeroffset | Configure the pixels that are not physically blocked. |
| lvd blockerwidth | Configure the pixels that are not physically blocked. |
| lvd edgedelay | Configure the edge delay for the hardware. |
| lvd highbias | Calibrate the high bias applied to the light valve. |
| lvd hightrim | Calibrate the high trim applied to the light valve. |
| lvd highvoltage | Calibrate the high voltage applied to the light valve. |
| lvd idleperiod | Configure the idle period for polarity switching. |
| lvd lowbias | Calibrate the low bias applied to the light valve. |
| lvd lowtrim | Calibrate the low trim applied to the light valve. |
| MED | |
| med <media index> beamcurve <polarity> | The target curve for the beam-balance. |
| med <media index> beampiston | Link the target profiles for the beam-balance. |
| med <media index> beamslope <polarity> | The target slope for the beam-balance. |
| med <media index> colour | The media colour for identifying media. |
| med <media index> drumspeed | The drum speed for the media. |
| med <media index> focusmode | The focus mode for the media. |
| med <media index> focuspower | The focus laser power reaching the surface the media. |
| med <media index> imagemode | The image mode for identifying media. |
| med <media index> laserpower | The write laser power for the media. |
| med <media index> name | The media name for identifying media. |
| med <media index> plotcounter | The plot counter for the media. |
| med <media index> rcvrgain | The receiver gain of the media. |
| med <media index> scorr <polarity / spot quad> | The stroke correction table for the media. |
| med <media index> sd | The surface depth of the media. |
| med <media index> sensitivity | The sensitivity for the media. |
| med <media index> sensitivityadjust | The sensitivity adjustment for the media. |
| med <media index> stroke <polarity / spot quad> | The stroke table for the media. |
| med <media index> strokeoffset | Configure the pixels used for plotting. |
| med <media index> strokewidth | Configure the pixels used for plotting. |
| med <media index> surfacevelocity | The surface velocity for the media. |
| NET | |
| net <interface> defaultgateway | Configures the default gateway of the network interface. |
| net <interface> hostname | Configures the hostname of the network interface. |
| net <interface> ipaddress | Configures the IP address of the network interface. |
| net <interface> macaddress <byte> | Configures the MAC address of the network interface. |
| net <interface> subnetmask | Configures the subnet mask of the network interface. |
| PLT | |
| plt <copy index> columnnumber | Configures the column number of the TPG pattern. |
| plt <copy index> combinationname | Configure the combination name of the TPG combination. |
| plt <copy index> combinationnumber | Configure the combination number of the TPG combination. |
| plt <copy index> patterndata <data index> | Configures the pattern data of the TPG pattern. |
| plt <copy index> patternname | Configures the pattern name of the TPG pattern. |
| plt <copy index> patternnumber | Configures the pattern number of the TPG pattern. |
| plt <copy index> rownumber | Configures the row number of the TPG pattern. |
| plt <copy index> rowrepeat | Configures the row repeat of the TPG pattern. |
| plt <copy index> stripenumber | Configure the stripe number of the TPG combination. |
| plt <copy index> stripepattern <stripe index> | Configure the stripe pattern of the TPG combination. |
| plt <copy index> stripewidth <stripe index> | Configure the stripe width of the TPG combination. |
| SAT | |
| sat devsinstalled | Install / uninstall satellites. |
| sat expectedhw | The expected hardware version for the satellite boards. |
| sat statmask0 | The status mask for status points 0 to 31. |
| sat statmask1 | The status mask for status points 32 to 63. |
| sat statmask2 | The status mask for status points 64 to 95. |
| sat statmask3 | The status mask for status points 96 to 127. |
| sat statmask4 | The status mask for status points 128 to 159. |
| SYS | |
| sys annealaccrual | The accrual time for the light valve annealing. |
| sys annealsetpoint | The setpoint time for light valve annealing. |
| sys bipolarcal | Enable / disable bipolar calibration. |
| sys comment | A comment that applies to the exposure head. |
| sys dpi | The maximum DPI of the exposure head. |
| sys firmwareversion | The firmware version used to detect firmware upgrades. |
| sys imagedata | Configure the source for the image data. |
| sys imagetiming | Configure the source for the image timing. |
| sys laseranneal | Enable / disable the light valve annealing. |
| sys laserenable | Enable / disable the write laser. |
| sys laserstandby | Enable / disable the write laser standby. |
| sys plotenable | Enable / disable plotting. |
| sys polarity | Configure the polarity type. |
| sys ratedpower | The rated power for the exposure head ( at full stroke width ). |
| sys serialnumber | The serial number of the exposure head. |
| sys standbyperiod | The period for the write laser standby. |
| sys standbythreshold | The threshold for the write laser standby. |
| sys standbytimeout | The timeout for the write laser standby. |
| sys tpgpattern | Configure the TPG pattern. |
| VBS | |
| vbs level <subsystem> | The verbose level for all subsystems. |