| ADC | |
| adc info | Display A/D conversion information. |
| adc mode (disable|enable) | Set the A/D conversion control mode. |
| adc stream (on <element>|off) | Enable / disable streaming of A/D samples. |
| BNK | |
| bnk allocate <size> | Allocate a memory block. |
| bnk free <address> | Free a memory block. |
| bnk info | Display bank information. |
| bnk mcb | Walk the linked-list of MCB's. |
| bnk read <address> <length> | Read word(s) from the bank. |
| bnk write <address> <value> | Write a word to the bank. |
| DBG | |
| code read <address> <length> | Read word(s) from the code space. |
| code write <address> <value> | Write a word to the code space. |
| data read <address> <length> | Read word(s) from the data space. |
| data write <address> <value> | Write a word to the data space. |
| io read <address> <length> | Read word(s) from the I/O space. |
| io write <address> <value> | Write a word to the I/O space. |
| stack info | Display stack information. |
| trace display | Display all trace entries. |
| trace mode (enable|disable) | Configure the trace mode. |
| DIO | |
| dio ignore hw | Ignore hardware errors. |
| dio ignore temp | Ignore temperature errors. |
| dio testgen [<pattern> [int]] | Control the internal test data generator. |
| ld (<diode>|all) (on|off) | Turn diode(s) on/off. |
| ld (<diode>|all) <current> ma | Set diode current(s). |
| ld (<diode>|all) <delay> delay | Set diode pixel delay(s). |
| ld (<diode>|all) mask (on|off) | Enable/disable diode masking. |
| ld all <value> dac | Set diodes to a dac value. |
| ld base (<current>|auto) | Set diode base current. |
| ld idle (on|off) | Turn idle current on/off. |
| ld save delay | Saves the temporary pixel delays to dio pix_delay. |
| ld zero | Turn off all diodes, zero the currents. |
| ld [<diode>] | Show the status of the diode(s). |
| safe [exit] | Enter of exit safe (currents off) mode. |
| DIR | |
| dir list | List all directory entries. |
| DOT | |
| ontime [e] | Display the diode odometer. |
| DPC | |
| dpc pcurve (<diode>|all) | Generate power curves. |
| dpc pcurve save original <password> | Save power curves as the original production values. |
| dpc points [<power_points>] | Set or view power curve points. |
| ld (<diode>|all) <power> mw | Set diode powers. |
| report | Report on the health of diodes. |
| DPS | |
| dps background | Set the background level of the power sensor. |
| dps calibrate <param1> <param2> | Depreciated - do not use. |
| dps calibrate save | Depreciated - do not use. |
| dps gain <diode> <gain> | Power sensor calibration - for use during manufacturing. |
| dps gain save | Power sensor calibration - for use during manufacturing. |
| dps raw range | Turn on each diode and print raw sensor value. |
| dps raw [<samples>] | Get raw values from power sensor. |
| dps read <diode> | Read power sensor and multiply by diode gain. |
| dps response <diode> <samples> [<power>] | Measure the time response of a diode. |
| ld <diode> read | Measure a diode's power. |
| ld all read [<ms_delay>] | Measure the power of all diodes. |
| DSC | |
| analyze [<medIndex>] [e] | Analyze the accuracy of a media strokes. |
| cal | Do a full power calibration. |
| cal abort | Abort an ongoing calibration. |
| cal med <medIndex> | Stroke calibrate a specific media. |
| cal pcurve | Calibrate just the power curves. |
| cal status | Show the status of an ongoing calibration. |
| dsc hotlink reset | Resets the hotlink error counter. |
| ld stroke | Set diodes to the stroke of the current media. |
| EED | |
| eeprom erase | Erase the EEPROM. |
| eeprom info | Display EEPROM information. |
| eeprom read <address> <length> | Read word(s) from the EEPROM. |
| eeprom verify | Verify the EEPROM. |
| eeprom write <address> <word> | Write a word to the EEPROM. |
| ERR | |
| err <code> | Print the error code. |
| err list | List all registered error codes. |
| FLS | |
| fls erase <address> | Erase a flash sector. |
| fls info | Display flash information. |
| fls read <address> <length> | Read word(s) from the flash. |
| fls write <address> <value> | Write a word to the flash. |
| HDW | |
| reset [soft] | Perform a hardware / software reset. |
| HIF | |
| laser (on|off) | Configure the write laser control mode. |
| shutter (open|close) | Open / close the internal shutter. |
| stroke cal | Perform a stroke calibration. |
| HSD | |
| hsd dac <channel> <level> | Set DAC channel. |
| HSP | |
| hsp send <address> <data> | Send to a device. |
| I2C | |
| i2c read <address> <length> | Read from I2C device. |
| i2c write <address> <data> | Write to I2C device. |
| i2c wrrd <address> <data> <length> | Write, read I2C device. |
| INT | |
| int info | Display INT information. |
| LOG | |
| log display [<offset> <width>] [wide] | Display the plot / sample data. |
| log dump [<offset> <width>] | Display the sample data in compressed format. |
| log focsetup [<bool NL>] [<bool imaging>] [<trigger>] [<sum divisor>] [<lpos divisor>] [<error divisor>] | Set up the log to collect focus data. |
| log info | Display LOG information. |
| log mode (plot|sample|off) | Set the LOG control mode. |
| log sample [<point> (enable|disable)] [<divisor>] | Display / configure the sample configuration. |
| log stop | Terminate the acquisition of plot / sample data. |
| log trigger [<index>] [<delay>] | Display / configure the trigger event. |
| MED | |
| med index <media index> | Select the media. |
| med info | Display media information. |
| MON | |
| (field|eng) | Set the access level. |
| help list | List all registered subsystems. |
| help [<subsystem>] | List registered commands. |
| monitor baud (9600|19200|38400|57600|115200) | Change the monitor baud rate. |
| MSG | |
| msg info | Display message information. |
| NUC | |
| nuc buffer | Display system memory pool buffers. |
| nuc pool | Display system memory pool information. |
| PRF | |
| parm receive | Receive parameter file and restore the parameters. |
| parm receive <firstkey> [<lastkey>] | Receive parameter file, restore specific keys. |
| parm receive <subsystem> | Receive parameter file, restore a subsystem. |
| parm send | Send parameter file to the PC host. |
| PRM | |
| prm copy <subsystem> [<parameter>] <source> <destination> | Transfer all subsystem parameters. |
| prm diff | List the baseline parameters. |
| prm dump | Dump all parameters. |
| prm list | List all registered subsystems. |
| prm restore | Restore the baseline parameters. |
| prm save | Save the baseline parameters. |
| set | List all registered subsystems. |
| set <subsystem> [<copy>] <parameter> [(<element>|all)] <value> | Write the parameter. |
| set <subsystem> [<copy>] [<parameter>] | Read the parameter. |
| RDR | |
| redirect (enable|pass|disable) | Configure the redirection mode. |
| redirect info | Display redirection information. |
| REG | |
| reg delete <number> | Delete a registry key. |
| reg dump | Dump all registry keys. |
| reg erase [baseline] | Erase the registry. |
| reg info | Display registry information. |
| reg optimize | Optimize the registry. |
| reg verify [baseline] | Verify the registry. |
| SBT | |
| fload bundle | Load the firmware bundle ( binary download ). |
| fload bundle y | Load the firmware bundle ( Y-modem download ). |
| SYM | |
| temp | Read all temperatures from the system monitor. |
| volt | Read all voltages from the system monitor. |
| SYS | |
| coldplot (on|off) | Plot without power to the diodes. |
| hold delay (on|off) | Hold the temporary diode pixel delays. |
| hold focus (on|off) | Hold the focus values. |
| hold mask (on|off) | Hold the diode plot mask. |
| hold power (on|off) | Hold manually set diode powers. |
| ignore focus (on|off) | Ignore focus commands. |
| ignore params (on|off) | Ignore MPE parameters. |
| sys fault (warning|fatal) [<number>] | Generate warning / fatal fault(s). |
| sys fault state | Determine the fault state. |
| sys fault [<point> (on|off)] | Display / configure the fault configuration. |
| sys info | Display system plot settings. |
| sys parm access <index> (disable|enable) | Configure host access to the system parameters. |
| sys parm config | Configure the system parameters. |
| sys parm [<index> <value>] | Display / write the system parameters. |
| TMR | |
| tmr pulse <width> | Generate a pulse stream. |
| URT | |
| urt info | Display uart information. |
| urt loopback [<size>] | Enter loopback mode. |
| urt swap | Swap the datalink and monitor ports. |
| urt txstring <size> | Tx string on MON port. |
| VBS | |
| vbs disable (<subsystem>|all) | Disable the verbose level for the subsystem(s). |
| vbs enable (<subsystem>|all) <level> | Enable the verbose level for the subsystem(s). |
| vbs list | List the verbose level for all subsystems. |
| VER | |
| ver | Display the firmware banner. |
| ver list | List all registered subsystems. |
| VPC | |
| vpc point <velocity> | Retrieve the current media's power point at the specified surface velocity. |
| vpc power <media> [<power_points>] | Read or set the power points on the velocity power curve for the specified media. |
| vpc velocity <media> [<velocity_points>] | Read or set the velocity points on the velocity power curve for the specified media. |
| YMD | |
| ymd rx [<length>] | Receive test file. |
| ymd tx <length> [<truncate>] | Send test file. |