Trendsetter AL - MCE Error Messages

Home | Contact Us | Submit Troubleshooting Info | Search | Help

MCE Error Messages

Trendsetter AL specific Errors | Base Trendsetter Errors

Errors specific to Trendsetter AL

This content is generated by scripts that pull information directly from Firmware Engineering's support site. The scripts were last run: 16 Jul 2008 17:30:34

Number		Error Message
40302		MDH: No plates detected in bay <Bay number>
40345		MDH: Please remove plate(s) from the outer bay [<I/O name>]
40346		MDH: The plate stack is too high to deploy the outer bay arms
40401		MDH: Picker up/down timeout: Failed to <Action> sensor. [<I/O name>]
40402		MDH: Picker in/out timeout: Failed to <Action> sensor. [<I/O name>]
40403		MDH: Picker wrist timeout: Failed to <Action> sensor. [<I/O name>]
40404		MDH: Picker vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]
40405		MDH: Cannot move the picker, it has not been initialized
40406		MDH: Plate not detected on picker
40407		MDH: Please remove plate detected on picker
40408		MDH: Please close plate cover
40409		MDH: Cannot move picker <Direction> because <Obstruction>
40410		MDH: Plates are sticking together. Please open the plate cover and separate the plates. Press RESUME to continue.
40411		MDH: Timeout waiting for plate cover to be opened/closed. Command cancelled
40412		MDH: Device ready. Close plate cover to continue.
40413		MDH: Picker wrist sensor is not working
40414		MDH: Picker wrist cylinder is faulty
40415		MDH: Separator arm timeout: Failed to <Action> sensor. [<I/O name>]
40416		MDH: Cannot move separators <Direction> because <Obstruction>
40417		MDH: Please close plate cover, or put the preloader into position
40420		MDH: The Preloader is in a faulted state. Please check the Preloader display for more information
40421		MDH: The Preloader is not ready. It may be out of position, open, or not fully powered on
40423		MDH: The Preloader is not powered on. Please check the Preloader connections
40424		MDH: The Preloader is in the bay. Please check the Preloader display for more information
40425		MDH: The Preloader is not loading plates properly into the Trendsetter bay. Please check the Preloader display for more information
40426		MDH: No plates detected in the bay. The plate may not have been properly loaded by the Preloader
40801		MDH: Unload table up/down timeout: Failed to <Action> sensor. [<I/O name>]
40802		MDH: Unload table cups up/down timeout: Failed to <Action> sensor. [<I/O name>]
40803		MDH: Unload table vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]
40804		MDH: Cannot move the unload table, it has not been initialized
40805		MDH: Timeout waiting for plate to leave unload table
40806		MDH: Unload cups rotated, cannot move unload table cups
40807		MDH: Unload stepper motor not in safe position to rotate cups
40809		MDH: Please remove plate detected on unload table [<I/O name>]
40810		MDH: Rotator timeout: Failed to <Action> sensor. [<I/O name>]
40811		MDH: Unable to pull media out of engine. Media still detected at entry sensor [<I/O name>]
40812		MDH: Media not detected at unload table entry [<I/O name>]
40814		MDH: The processor is not ready to accept plates
40815		MDH: The processor is in a faulted state
40816		MDH: The processor is still busy with the previous plate, so is unable to accept another

Base Trendsetter Errors

This content is generated by scripts that pull information directly from Firmware Engineering's support site. The scripts were last run: 16 Jul 2008 17:30:30

Number		Error Message
33256		BFD: Not in download state
33257		BFD: Firmware already in download mode
33258		BFD: Binary file download not complete
33259		BFD: Invalid download handle
33260		BFD: Binary File Header bytes were not zero
33261		BFD: Binary File Illegal Tag value(s) found
33262		BFD: Unknown download type
33263		BFD: unknown destination type specified
33264		BFD: Bad checksum calculated
33265		BFD: DOWNLOAD START message received, but not in IDLE state
33266		BFD: CPU reset type equals boot level
33267		BFD: Unknown Flash Manufacturer
33268		BFD: Unknown Flash Device or Failure Identifying Flash Device
33269		BFD: Failure writing flash
33270		BFD: Failure writing FW Dir entry for BBR Code
33271		BFD: Failure writing FW Dir entry for Xilinx
33273		BFD: No firmware directory entries available
33274		BFD: Error code not used
33276		BFD: Binary Upload data is exhausted
33277		BFD: Failure writing FW Dir entry for Overwriting data
33501		MSG: Message not reserved
33502		MSG: Invalid argument list
33503		MSG: Incorrect message type
33504		MSG: Incorrect message group
33505		MSG: Command queue is empty
33506		MSG: Timeout waiting on command queue
33507		MSG: String queue is empty
33508		MSG: Timeout waiting on string queue
33509		MSG: Message not released
33510		MSG: No messages in pool remaining
33511		MSG: Timeout waiting for message response
33512		MSG: Maximum head message is 31 bytes
33513		MSG: Failure Sending String Message - Queue Full
33514		MSG: No strings in pool remaining
33516		MSG: Message tracing is disabled
33517		MSG: Zero message trace buffers are allocated
33518		MSG: Internal firmware error
33519		MSG: Command code is filtered and not logged into trace buffer
33520		MSG: Message tracing is not disabled, cannot perform requested action
33521		MSG: Reached the end of the message trace buffer list
33522		MSG: No more free message trace filter entries
33523		MSG: A trace filter with the specified command code exists
33524		MSG: Command code not in trace filter list
33600		STG: Storage Key was not found
33601		STG: Storage Key data block is the wrong size
33602		STG: Storage medium is corrupt
33603		STG: Storage medium is full
33604		STG: More than one type of non-volatile storage medium specified
33605		STG: Invalid Subsystem Number specified for Key
33606		STG: Invalid Private Key Number specified for Key
33607		STG: End of NVS storage found
33608		STG: Storage Medium was recovered from backup
33609		STG: Access to STG Subsystem was Blocked
33610		STG: Invalid function parameter passed to an STG API function
33611		STG: Duplicate Key(s) present in NVS
33612		STG: The type of NVS specified does not exist in this product.
33613		STG: Attempted to write past the end of a STG RAM search table
33614		STG: The specified configuration code is invalid
33615		STG: The specified Nvs medium is not supported by the called function
33616		STG: Configuration failed
33617		STG: Storage medium is not initialized, it cannot be used
33618		STG: Storage medium is corrupt, it cannot be used
33619		STG: Storage medium is corrupt - key data checksum failed
33620		STG: Storage medium is corrupt - key storage control block checksum failed
33621		STG: Storage medium is corrupt - initialized values not set
33622		STG: Invalid storage partition
33623		STG: Invalid storage granularity
33624		STG: Cannot recover NVS medium, only one partition available
33700		MON: Diagnostic NT pipe to SVCHOST is not created
33701		MON: undefined error for monitor command
33702		MON: Failed to create a line editor component
33703		MON: The line editor has disabled forwarding to the terminal
33900		ERR: Description not found
33901		ERR: Too many error groups defined
33903		ERR: No error descriptor partitions left
33904		ERR: Test: <test string pointer> <test decimal value 16-bit integer> <test string pointer> <test pseudo float value (32-bit integer> <test string pointer> <test long 32-bit unsigned integer> <test string pointer> <test 16-bit hexadecimal value>
33905		ERR: Error group is invalid
33906		ERR: Error parameter overflow
33907		ERR: Firmware integrity failure
33908		ERR: Parameterized error table is full, all indexes are reserved
33909		ERR: Error buffer has overrun
33910		ERR: Error buffer is invalid
34000		PRM: Invalid function parameter(s) sent into API function
34001		PRM: Invalid parameter group identifier
34002		PRM: Duplicate registration of parameter group table
34003		PRM: Invalid parameter group table
34004		PRM: Duplicate parameter key found
34005		PRM: Invalid parameter key
34006		PRM: The search is complete
34007		PRM: The buffer size specified does not match buffer size for NVS parameter key
34008		PRM: The specified group description has not been found
34009		PRM: The parameter has not been found
34010		PRM: The parameter copy index is invalid
34011		PRM: The parameter element index is invalid
34012		PRM: The parameter syntax is invalid
34013		PRM: The parameter range is invalid (name="<Name of offending parameter>" key=<Key of offending parameter>)
34014		PRM: The string parameter syntax is not supported
34015		PRM: The string parameter length is invalid
34016		PRM: Unexpected software failure
34017		PRM: The functionality has not been implemented
34018		PRM: The PRM command is in progress
34019		PRM: No parameter table was registered for this group
34020		PRM: A zero is sent as the DataLength function parameter
34021		PRM: The PRM internal data buffer size is too small
34022		PRM: No more available overflow system table entries
34023		PRM: The group descriptions are inconsistent
34024		PRM: The NVS system table is corrupt
34025		PRM: NVS medium is corrupt
34026		PRM: STG subsystem General failure
34027		PRM: The NVS medium is full
34028		PRM: A STG key already exist with a different data block size
34029		PRM: Parameter key not found in NVS
34030		PRM: No default is associated with parameter
34031		PRM: No NVS is detected
34032		PRM: Parameter subsystem is not initialized
34033		PRM: Cannot modify parameter, not in configuration mode
34034		PRM: Cannot modify parameter, not in media mode
34035		PRM: The specified configuration code is invalid
34036		PRM: Configuration failed.
34037		PRM: Command cancelled
34038		PRM: This parameter is read-only
34039		PRM: Restricted parameter, insufficient access level
34040		PRM: This parameter is not accessible from the diagnostic monitor
34041		PRM: Parameter '<Group name><Index reference> <Short name><Element name>' changed from <Original value> to <New value> <Units>
34101		UTL: no saved records in history table
34102		UTL: invalid parameter
34103		UTL: pipe handle is invalid
34104		UTL: pipe is now full
34105		UTL: pipe is now empty
34106		UTL: data pipe could not be created
34107		UTL: data pipe could not be deleted
34108		UTL: Reached the end of a linear link list
34109		UTL: Memory Allocation Failure
34110		UTL: The pipe information has not registered
34111		UTL: Pipe is opened
34112		UTL: Connecting NT pipe
34113		UTL: Pipe not connected, cannot retrieve pipe name
34114		UTL: Failed to create and connect NT Pipe
34115		UTL: The destination pipe id is invalid
34116		UTL: The source pipe id is invalid
34117		UTL: The buffer to hold PipeName is too small
34118		UTL: Failed to read from NT pipe
34119		UTL: Sending too much data through an NT pipe
34120		UTL: Cannot disable interrupts when performing link list index search
34121		UTL: Conversion failed, software error
34122		UTL: No data is ready in the specified queue
34123		UTL: Cannot read from the board's IIC port
34124		UTL: Cannot write to the board's IIC port
34125		UTL: Fixed-size queue full
34126		UTL: Fixed-size queue empty
34127		UTL: Invalid format type for conversion
34128		UTL: Invalid engineering units for conversion
34129		UTL: Attempted to register too many override function tables
34130		UTL: Attempted to override the same function more than once
34131		UTL: Cannot override function because function cannot be found
34132		UTL: Cannot override function because override table not registered
34133		UTL: Attempt to register override table or override function after system initialization
34200		BCM: invalid port ID specified
34201		BCM: internal buffer space full
34202		BCM: timeout waiting for ACK
34203		BCM: general failure
34204		BCM: internal buffers exhausted
34205		BCM: HDLC CRC receiver error
34206		BCM: failure to create WIN32 thread
34207		BCM: client receive buffer too small
34208		BCM: received HDLC pkt not for us
34209		BCM: port is in 'Raw' mode
34210		BCM: can't send, no Carrier Detect
34211		BCM: timer thread create failure
34212		BCM: out of virtual connection buffers
34213		BCM: virtual connection was lost
34214		BCM: no more internal HDLC buffers
34215		BCM: transmit timeout multiplex error
34216		BCM: no multiplex communications occuring
34217		BCM: The BCM_PORT is not of type NT Pipe
34218		BCM: Invalid function parameter detected
34219		BCM: The pipe information has not registered
34220		BCM: Pipe is opened
34221		BCM: Connecting NT pipe
34222		BCM: Pipe not connected, cannot retrieve pipe name
34223		BCM: Failed to create and connect NT Pipe
34224		BCM: The destination pipe id is invalid
34225		BCM: The source pipe id is invalid
34226		BCM: The buffer to hold PipeName is too small
34227		BCM: Failed to read from NT pipe
34228		BCM: The specified BCM port is not opened
34229		BCM: Sending too much data through an NT pipe
34230		BCM: Baud Rate specified is too high
34231		BCM: Invalid Baud rate
34232		BCM: Transaction List Underflow
34233		BCM: HDLC Address Invalid or Unknown
34234		BCM: DOP Address Invalid or Unknown
34235		BCM: DNE-ICE Auto ID failure
34236		BCM: DNE-ICE Communication setup failure
34237		BCM: DNE-ICE Communication shutdown failure
34238		BCM: DNE-ICE connection failure
34239		BCM: DNE: receive timout failure on ICE data
34240		BCM: Transmission Cancelled
34241		BCM: Can't open W32 serial Port
34242		BCM: Can't initialize comm port buffers in Win32
34243		BCM: Access attempted to unsupported port in Win32
34244		BCM: Error while closing port
34245		BCM: Error while writing to port
34301		DPC: undefined pattern number
34302		DPC: close of closed scan
34303		DPC: close of un-open scan
34304		DPC: write to undefined scan
34305		DPC: call with NULL pattern struct
34306		DPC: Too many cells in pattern
34307		DPC: Pattern write call error
34308		DPC: write to un-opened scan
34309		DPC: write to closed scan
34310		DPC: open of NULL scan
34311		DPC: memory overflow
34312		DPC: too many scans
34313		DPC: timed out waiting for stripe to complete
34320		DPC: SCSI Driver Error, line <Line Number>
34321		DPC: SCSI driver error, invalid initiator
34322		DPC: SCSI asynchronous transfer requested, line <Line Number>
34323		DPC: SCSI parity error detected
34324		DPC: SCSI bus reset detected
34331		DPC: orthog slope smaller than minimum, check plate rotation
34332		DPC: orthog slope larger than max, check plate rotation
34333		DPC: OCCT SDRAM Test fail - Address = <Address>, Write data = <Write data>, Read data = <Read data>
34334		DPC: SDRAM module was not detected
34335		DPC: RIP resolution is invalid
34336		DPC: Pixels per stroke is invalid
34337		DPC: Subscan duplicate is invalid
34338		DPC: Mainscan duplicate is invalid
34339		DPC: Drum diameter is invalid
34340		DPC: Mainscan length is invalid
34341		DPC: Mainscan length is not a multiple of 32
34342		DPC: Pixels per stroke is not a multiple of 8
34343		DPC: DPC subsystem received unknown command message
34344		DPC: Stroke width not a multiple of subscan replication
34345		DPC: Reserved Error Code 1
34346		DPC: Reserved Error Code 1
34350		DPC: Data transfer already in progress
34351		DPC: Data transfer not in progress
34352		DPC: memory test not defined
34353		DPC: memory test failed at address
34354		DPC: too much data has been received
34355		DPC: too little data has been received
34356		DPC: Data channel not detected
34357		DPC: Datapath operation was preempted
34358		DPC: Image padding limit was exceeded
34359		DPC: No blank regions available for use
34360		DPC: No blank regions currently being used
34361		DPC: Invalid OCCT pointer send to datapath
34800		RIF: Image property parameter not found in list
34801		RIF: Image property list is invalid
34802		RIF: Image property type is invalid
34803		RIF: Message type is invalid
34805		RIF: Cannot merge image property lists
34810		RIF: Received invalid command code from workstation
34811		RIF: Received invalid parameter from workstation
34812		RIF: Command code received from workstation is not supported
34813		RIF: Received non-zero value in reserved field from workstation
34820		RIF: No more resolutions supported
34821		RIF: Resolution mode not defined
34822		RIF: Invalid resolution specified
34823		RIF: No more media supported
34855		RIF: Too many timestamps in timing loop-back packet
34856		RIF: Cannot timestamp a non timing loop-back packet
34857		RIF: Signifies that the packet represents a timing loop-back
34858		RIF: The input function parameter is incorrect
34900		RTL: failure
34901		RTL: no free transactions
34902		RTL: no match
34903		RTL: full
34904		RTL: addressing conflict
34905		RTL: no route found
34906		RTL: timeout
34907		RTL: port not opened
34908		RTL: NT COM port or pipe conflict
34909		RTL: Invalid Source Id String
34910		RTL: Invalid Destination Id String
34911		RTL: Cannot determine which DNE instance to connect to
34912		RTL: RTL transaction has already been freed
34913		RTL: No Communications to Target Device
34914		RTL: Route buffer is reserved by non-streaming messages
34915		RTL: The indexed RTL transaction is invalid
34916		RTL: Invalid CDI communication profile
34917		RTL: BCM port cannot be opened
34918		RTL: Linked List Protection Semaphore Fault
34919		RTL: Transaction flushed from RTL list
35702		PRD: unable to find subsystem name
35703		PRD: unable to find specified record
35706		PRD: unable to find specified subsystem number
35707		PRD: called function is not applicable for this product
35708		PRD: version information has already been registered
35709		PRD: version information has not been registered yet
35710		PRD: The run-time option specified does not exist
35711		PRD: Could not save the run-time option setting to NVS
35712		PRD: Flyoff occurred, remove media
35713		PRD: Flyoff sensor blocked, check machine for loose media, or check flyoff sensor
35714		PRD: Roller down, cannot move nor spin the drum
35718		PRD: Trailing edge backbone is down, cannot move or spin the drum
35720		PRD: Safety sense is not on, check doors and emergency off switch
35722		PRD: Media partially loaded on drum, cannot move nor spin drum
35724		PRD: Emergency stop switch is on
35733		PRD: Front panel is open, check front panel
35735		PRD: Back panel not detected, check back panel
35738		PRD: Cannot unlock doors if the drum is spinning
35741		PRD: Invalid Temperature Reading Attempted
35743		PRD: Invalid NVS key in callback
35744		PRD: The write laser could not be turned on because the safe line is not high
35745		PRD: The write laser relay did not activate as asked, it may be welded
35746		PRD: The drum amp relay did not activate as asked, it may be welded
35747		PRD: The main power relay did not activate as asked, it may be welded
35748		PRD: System Presence Fault: <Presence detect bit description> (<Presence detect bit name>) Not Detected
35749		PRD: System Input Fault: <Input bit description> (<Input bit name>) In Unexpected State
35750		PRD: System Output Fault: <Output bit description> (<Output bit name>) In Unexpected State
35751		PRD: System Range Fault: <Analog bit description> (<Analog bit name>) Out Of Range: Low=<Low range limit>, High=<High range limit>, Reading=<Current value>
35752		PRD: System Range Warning: <Analog bit description> (<Analog bit name>) Out Of Range: Low=<Low range limit>, High=<High range limit>, Reading=<Current value>
35756		PRD: Drum is spinning when a stationary drum is expected
35757		PRD: Hardware can't generate requested tach simulation velocity
35758		PRD: Leading edge backbone is down, cannot move the drum
35766		PRD: Invalid model configuration specified
35767		PRD: Ramp is in near the drum, cannot spin the drum
35772		PRD: System Pressure Out of Range: Reading=<Low range limit>, Low=<High range limit>, High=<Current value> (<Analog group name>)
35773		PRD: Top panels not detected, check top panels
35774		PRD: Top door is open, check top door
35775		PRD: Fanbox panel is not detected, check fanbox panel
35776		PRD: Invalid safety array entry specified
35777		PRD: Fatal error triggered
35778		PRD: Invalid callback
35779		PRD: User issued an abort, use 'abort clear' to clear the abort
35780		PRD: <Group name> Presence Fault: <Presence detect bit description> (<Presence detect bit name>) Not Detected
35781		PRD: <Group name> Input Fault: <Input bit description> (<Input bit name>) In Unexpected State
35782		PRD: <Group name> Output Fault: <Output bit description> (<Output bit name>) In Unexpected State
35783		PRD: <Group name> Range Fault: <Analog bit description> (<Analog bit name>) Out Of Range: Reading=<Current value>, Low=<Low range limit>, High=<High range limit>
35784		PRD: <Group name> Range Warning: <Analog bit description> (<Analog bit name>) Out Of Range: Reading=<Current value>, Low=<Low range limit>, High=<High range limit>
35785		PRD: <Group name>: All faults cleared
35786		PRD: Front panel is unlocked
35789		PRD: Media detected on the load ramp, cannot spin drum. Please remove media from the ramp
35790		PRD: Model code is invalid or unavailable
35791		PRD: Limit tag is not specified in the limit table
35792		PRD: Invalid optional value found. Limit tag [<Limit Tag>]. Value <Optional Value>.
35793		PRD: <Limit description> is <Limit value> <Unit>. <Parameter> <Unit> exceeds the limit.
35794		PRD: <Limit description> is <Limit value> <Unit>. <Parameter> <Unit> is lower than the minimum.
35795		PRD: <Limit description> must be <Limit State>.
35796		PRD: <Limit description> do not contain option flag <Option flag>. Cannot enable the option.
35797		PRD: <Limit description> is <Limit value> <Unit>. <Parameter> <Unit> is not equal to the limit.
35798		PRD: Key switch is on, drum speed limited to <Drum Speed> RPM
35800		_376: reset induced by software watchdog
35801		_376: reset induced by halt monitor
35802		_376: reset induced by RESET opcode
35803		_376: reset cause unknown
35804		_376: reset triggered by crash dump handler
36001		VBS: specified subsystem number is not registered
36002		VBS: specified output device is not applicable for this product
36200		URT: invalid serial port ID specified
36201		URT: serial port not opened yet
36202		URT: pipe access failed; pipe may be full (TX) or empty (RX)
36203		URT: illegal option specified
36204		URT: UART disabled
36501		BRD: Internal Error - Failed to create a Nucleus PLUS Timer
36502		BRD: Internal Error - Failed to control a Nucleus PLUS Timer
36503		BRD: Internal Error - Failed to Reset a Nucleus PLUS Timer
36504		BRD: Flash Driver code does not support this command primitive
36505		BRD: Flash Driver code has failed to program flash memory
36506		BRD: Flash Driver code has failed to erase a flash sector
36507		BRD: Insufficient memory to hold assembler flash driver routines
36508		BRD: The flash memory write operation failed to verify
36509		BRD: The address specified does not point to flash memory
36510		BRD: No Xilinx (LCA) was found in flash memory
36511		BRD: Undefined error
36512		BRD: Undefined error
36513		BRD: Board temperature sensor initialization failed
36514		BRD: No Overwriting pattern file (OVWR) was found in flash memory
36800		HLT: DNE not initialized (set DNE init 1)
36801		HLT: Invalid Parameters Sent to HLT Function
36802		HLT: Requested element is not registered
36803		HLT: Requested subsystem is not registered
36804		HLT: Internal HLT Subsystem Error
36805		HLT: A Subsystem has timed out
36806		HLT: Subsystem reported with unrecoverable error
36807		HLT: No cable detected between DNE and ICE
36808		HLT: BCM comm. between DNE and ICE has stopped
36809		HLT: The specified print unit is currently offline
36810		HLT: No Subsystem has reported in yet
36811		HLT: The system/subsystem is starting up
36812		HLT: Subsystem shutdown is currently taking place
36813		HLT: HLT subsystem has not initialized
36814		HLT: Workstation is not detected
36815		HLT: Feature is not available yet
36816		HLT: Firmware resource is low
36817		HLT: Print unit is online, connection checking not done
36818		HLT: SCSI Disk has errors
36819		HLT: SCSI disk not detected
36820		HLT: End of list detected
36821		HLT: Board temperature is above threshold
36822		HLT: Board temperature is above maximum limit
36900		MCE: Insufficient Heap Memory - required for DF1 serial drivers
36901		MCE: WMD Subsystem RCON Incoming Command Register Failure
36902		MCE: SDRAM Operation Failure
37420		PHS: TH2 error [<error code>] <error string>
37701		DRS: software error
37702		DRS: Drum operation timed out
37703		DRS: Drum is reserved, command ignored
37704		DRS: Overflow in internal drum calculation
37705		DRS: Tach simulator preventing drum servo control
37706		DRS: The current drum command has been preempted
37707		DRS: Drum servo control missing interrupts
37708		DRS: Specified drum velocity out of range
37709		DRS: Drum Hardware Missing <Description of the faulted hardware component>
37710		DRS: Drum Position Counter Overflow
37711		DRS: Specified Drum Torque out of range
37712		DRS: Drum Position Not Settling
37713		DRS: Drum Velocity Exceeded 100 Rpm in Torque mode
37714		DRS: Drum Velocity Error Exceeded
37715		DRS: Drum can't move to position at zero velocity
37716		DRS: Drum failed to reach position
37717		DRS: Number of allowable drum callbacks exceeded
37718		DRS: Drum target velocity invalid for PLL calculations
37719		DRS: Drum parameter patch range error: <Name of the drum NVS parameter that can not be patched because>
37720		DRS: Drum command passed an invalid pointer parameter
37721		DRS: Drum cannot use an encoder resolution of 0
37722		DRS: Drum can't stop at position when not moving
37723		DRS: Operation blocked while drum is freewheeling
37801		LCA: Xilinx LCA program failed
37802		LCA: Xilinx LCA file not found
37803		LCA: Xilinx LCA file checksum error
37804		LCA: LCA interrupt failed to register callback properly
37805		LCA: Feature not supported by the Xilinx firmware
37806		LCA: Invalid Latch ID specified
37807		LCA: Xilinx configuration failed
37808		LCA: SDRAM operation failed
37809		LCA: Overwriting pattern verification failed
37810		LCA: Invalid Overwriting Pattern detected
37811		LCA: Hardware can't generate requested tach simulation velocity
37812		LCA: <Feature> requires at least Xilinx v<Major version number>.<Minor version number>, current Xilinx is v<Major version number2>.<Minor version number2>
37813		LCA: Overwriting pattern <PatternID> is not licensed on this device
38101		MPC: Plot has been aborted
38102		MPC: Plot Mode is out of range or not valid
38104		MPC: Not configured for <Mainscan resolution> by <Subscan resolution> DPI resolution
38105		MPC: Startscan delay <Startscan delay> sub-pixels must be at least zero
38106		MPC: Total startscan delay <Startscan delay> sub-pixels is too large
38107		MPC: Mainscan image size <Mainscan image size> pixels too large, maximum is <Maximum image size> pixels
38108		MPC: Could not find edge of media after <Search attempts> attempts
38109		MPC: Head not configured for '<Media name>/<Media colour>/' media
38110		MPC: The carriage start position <Carriage start position> mm is beyond the home tab
38111		MPC: Timeout waiting for image data
38113		MPC: No resolution modes configured
38115		MPC: Invalid plot parameter ('<Parameter name>' = <Parameter value>)
38116		MPC: No valid edge found, check edge detect strip
38117		MPC: Internal: Invalid parameter passed to function
38118		MPC: Internal: System resource unavailable
38119		MPC: Midpoint position <Midpoint position> um too small for subscan media size
38120		MPC: Phase Lock Loop losing lock
38121		MPC: Debris removal not running as expected
38122		MPC: The '<Sequence name>' sequence is currently being processed
38123		MPC: The Phase Lock Loop could not be started
38124		MPC: The Phase Lock Loop cannot accommodate <Mainscan resolution> DPI
38125		MPC: The drum speed is too high for imaging, maximum is <Maximum drum speed> RPM
38126		MPC: The Xilinx firmware must be upgraded
38127		MPC: Mainscan image size <Mainscan image size> pixels must equal gapless drum circumference <Drum circumference> pixels
38128		MPC: Mainscan shift <Mainscan image shift> um larger than gapless drum circumference
38129		MPC: The specified sequence is not supported
38130		MPC: The pattern stroke width (<Pattern stroke width>) must equal the head (<Head stroke width>)
38131		MPC: Registration pins <First pin> and <Second pin> are configured incorrectly
38132		MPC: Media not on <Registration pin> registration pin
38134		MPC: Multiple plates detected on drum
38136		MPC: Subscan output resolution of <Subscan output resolution> DPI must equal head resolution
38138		MPC: Invalid media stack identifier <Media Stack Identifier> specified
38139		MPC: Cancel ignored, no sequence in progress
38142		MPC: Subscan image size <Subscan image size> pixels too large, maximum is <Maximum image size> pixels
38143		MPC: Internal: Expected plot sequence is not active
38144		MPC: The carriage end position <End position> mm is beyond the maximum travel distance <Maximum carriage travel> mm
38145		MPC: The media is sensitive to retraces and one or more retraces occurred
38146		MPC: Forced failure
38147		MPC: Head is not yet initialized
38148		MPC: Xilinx version <Current major version>.<Current minor version> is invalid, must be at least <Minimum required major version>.<Minimum required minor version>
38149		MPC: The head model installed is incompatible with this machine
38150		MPC: Image data sent to the head was possibly corrupted. Check plate for artifacts
38151		MPC: Invalid media type (<Media type>) for this operation
38152		MPC: Total amount of clamp shadow is too large
38153		MPC: Slave head resolution: <Head resolution on the slave board> DPI does not match with the one on the master: <Head resolution on the master board> DPI
38154		MPC: Slave head swath width: <Head swath width on the slave board> does not match with the one on the master: <Head swath width on the master board>
38155		MPC: Overwriting not allowed with pixel replication
38158		MPC: Timed out waiting for plot engine to initialize
38159		MPC: Communication failed between master and slave MCE boards
38161		MPC: The Phase Lock Loop did not stabilize
38164		MPC: Not configured for <Subscan resolution> DPI subscan resolution
38165		MPC: Variable mainscan resolution is not supported
38166		MPC: Carriage position is wrong - carriage has probably stalled
38167		MPC: <Head name> image is outside of the head's range (position <The position that triggered the error> um)
38171		MPC: Raster image data received from workstation was possibly corrupted. Check plate for artifacts
38172		MPC: Timed out waiting for raster image data CRC from workstation
38173		MPC: All heads are currently disabled
38176		MPC: Swath width is invalid, extra scanlines <Extra scanlines for current media> >= stroke width <Head stroke width>
38177		MPC: Media subscan size <Media Subscan Size> um is too long for registration pin configuration
38180		MPC: Slave error buffer overflow, unable to read slave error
38181		MPC: Plotting speed <Calculated carriage speed> mm/sec (<Pixels advanced per drum rotation> PPR at <Drum speed> RPM) exceeds licensed limit of <Carriage speed limit>
38183		MPC: Drum speed <Target drum speed> is too fast for <Target resolution> DPI resolution, maximum is <Maximum drum speed> RPM
38184		MPC: The media type '<Media name>' is not currently allowed on this device
38185		MPC: Current stroke width of <Current Stroke Width> is greater than allowed maximum of <Maximum Licensed Stroke Width>
38186		MPC: Workstation Fault [<Image error code>] <Image error text>
38188		MPC: '<Sequence table>', sequence '<Sequence>' (<Sequence address>), failure action <Failure action> not found
38189		MPC: ExtraScanlines and StrokeWidth set incorrectly for the yaw test pattern
38190		MPC: Phase Lock Loop possibly losing lock, error = <Phase error microns> microns (<Phase error clock cycles> clock cycles)
38191		MPC: The head unexpectedly reset
38192		MPC: The <Plate identifier> is positioned <Error distance> mm too close to the <Error direction> side
38193		MPC: The <Plate identifier> is positioned too close to the <Error direction> side
38194		MPC: The write laser is stuck calibrating
38195		MPC: The gc mainscan shift is too small
38197		MPC: The head is over the media at the minimum edge search position
38200		MIC: Error message with no error code
38201		MIC: Software error
38202		MIC: No image tasks available
38203		MIC: Image task is not active
38204		MIC: Image task is busy
38205		MIC: Image task is not suspended
38206		MIC: Image parameter is missing
38207		MIC: Image parameter is invalid
38208		MIC: Currently not initialized, waiting for FLUSH
38209		MIC: Flush is not complete
38210		MIC: Image parameters already received
38211		MIC: Too many image tasks requested
38212		MIC: Already unloading media
38213		MIC: Image cancelled by flush
38214		MIC: Cannot free unreserved image task
38215		MIC: Invalid image task identifier
38216		MIC: Cannot free busy image task
38217		MIC: Cannot free busy image task
38218		MIC: Fatal error
38219		MIC: Software error: <Additional information on the software error>
38220		MIC: Command aborted
38221		MIC: Task specified is not a valid image task
38222		MIC: Task specified cannot be cancelled
38223		MIC: Task has error, but a second error has occurred
38224		MIC: Image task specified is not a valid image (or not currently running)
38225		MIC: Task specified could not be found (no matching state machine)
38226		MIC: Task cancelled
38227		MIC: Task has not completed
38228		MIC: Flush not currently active
38229		MIC: Group index not in valid range
38230		MIC: Group image index not in valid range
38231		MIC: Group not valid, no images
38232		MIC: Invalid callback supplied
38233		MIC: Invalid image status structure supplied
38234		MIC: Invalid flush status structure supplied
38235		MIC: Invalid task parameter structure
38236		MIC: Invalid image parameter structure
38237		MIC: Invalid image list array supplied
38238		MIC: Invalid state type received in message
38239		MIC: Invalid command ID in command msg
38240		MIC: No state machines available
38241		MIC: State machine not found (no magic number match)
38242		MIC: State machines pointer invalid
38243		MIC: Message invalid, cannot parse
38244		MIC: Conditional false - internal only
38245		MIC: Invalid media type structure
38246		MIC: Media instance not being used by MIC
38301		MDS: Software error
38302		MDS: Software error, unable to allocate sequence data structure
38303		MDS: Software error, the Scheduler is trying to use a NULL sequence data struct
38304		MDS: Software error, the Scheduler is trying to use a invalid sequence structure pool
38305		MDS: Software error, the Scheduler is trying to use a invalid sequence structure linked list
38306		MDS: Software error, the Scheduler could not remove the sequence structure from the linked list
38307		MDS: Software error, unable to allocate media data structure
38308		MDS: Software error, the Scheduler is trying to use a NULL media data structure
38309		MDS: Software error, the Scheduler is trying to use a invalid media structure pool
38310		MDS: Software error, the Scheduler is trying to use a invalid media structure linked list
38311		MDS: Software error, the Scheduler could not remove the media structure from the linked list
38312		MDS: Software error, unable to allocate arguments data structure
38313		MDS: Software error, the Scheduler is trying to use a NULL arguments data structure
38314		MDS: Software error, the Scheduler is trying to use a invalid arguments structure pool
38315		MDS: Cancel command failed, Scheduler not currently processing any operation with specified media instance
38316		MDS: Scheduler could not schedule command since it did not have a proper arguments
38317		MDS: Image type specified is not supported by this machine
38318		MDS: Scheduler monitor command failed
38319		MDS: Initialization failed use 'resume' to re-attempt initialization
38320		MDS: Scheduler command aborted
38321		MDS: Scheduler command cancelled
38322		MDS: Software error, suspend button not defined
38323		MDS: No <media name> on the drum to unload
38324		MDS: Scheduler cannot cancel unload commands
38325		MDS: Cannot cancel initialization commands
38326		MDS: Cannot eject during an unload
38327		MDS: Cannot eject media during initialization
38328		MDS: Scheduler sequence is in an unknown state
38329		MDS: The <Media name> on the drum is already being unloaded
38330		MDS: Scheduler has no tasks currently suspended
38331		MDS: Software error, Scheduler received a bad Media Hander task ID in it callback
38332		MDS: Software error, Scheduler received an invalid action type when setting up its arrays
38333		MDS: Invalid parameter sent to monitor command
38334		MDS: Media already on drum, cannot force new media on drum
38335		MDS: The parameter 'media stacks' is not used, only 1 stack available
38336		MDS: The parameter 'bay' is not used, no bays are available on this device
38337		MDS: The parameter 'punch' is not used, no punches are available on this device
38338		MDS: The parameter 'exit' is not used, only one exit on this device
38339		MDS: Attempt to load proofing media without carrier or receiver on drum
38340		MDS: Media scheduler fatal error
38341		MDS: Media type argument is invalid, media type = <Media type value that is invalid>
38342		MDS: Media stacks argument is <Current media stack value>, maximum = <Maximum media stack value>
38343		MDS: Media stacks argument cannot be 0, must be 1 or greater
38344		MDS: Bay argument cannot be 0 for an automatic job
38345		MDS: Bay argument is <current bay argument>, maximum is <maximum number of bays>
38346		MDS: Bay argument is <current bay argument>, but it is a manual job so it should be 0
38347		MDS: Punch argument is <current punch argument>, maximum is <maximum number of punches>
38348		MDS: Exit argument is <current exit argument>, maximum is <maximum number of exits>
38349		MDS: Rotate argument is <current rotate argument>, rotator is not supported
38350		MDS: Image side argument is invalid, must be set to a defined value for this media
38351		MDS: Image side argument is not valid for this media, must be set to Side A
38352		MDS: Image side argument is greater than expected, set to a valid value
38353		MDS: Default load arguments have been reset to valid values
38354		MDS: Default unload arguments have been reset to valid values
38355		MDS: Invalid media instance, 0 is not a valid media instance
38356		MDS: Invalid media instance, does not match media on the drum
38357		MDS: Requested media is not loaded
38358		MDS: Stack locations specified for <number of stack locations specified> stack(s), however <number of stacks being loaded> stack(s) are being loaded
38359		MDS: Cannot unload <media type> since it is still being loaded (possibly suspended)
38360		MDS: Cannot unload <media type> since <media being loaded on top> is being loaded on top
38361		MDS: Cannot unload <media type> since <media name(s) on top> is/are loaded on top
38362		MDS: Media Scheduler operation is undefined
38363		MDS: Media Scheduler <Operation Sequence Type> operation (<Media Instance ID>) cannot be run because the Media Handler is not initialized
38364		MDS: Media Scheduler <Operation Sequence Type> operation (<Media Instance ID>) is not allowed to be cancelled
38365		MDS: Media Scheduler <Operation Sequence Type> operation (<Media Instance ID>) could not schedule cycle testing operations (error:<Error code>)
38366		MDS: Media Scheduler operation <Media Instance ID> has an unknown sequence type <Sequence Type>
38367		MDS: Media Scheduler <Operation Sequence Type> operation (<Media Instance ID>) could not find a sequence to run
38368		MDS: Media Scheduler could not find step Id <Step Id> in sequence
38369		MDS: Media Scheduler <Operation Sequence Type> operation (<Media Instance ID>) could not find synchronization step Id <Step Id> in sequence (process Id:<Process Id>)
38370		MDS: Media Scheduler could not find end step in sequence
38371		MDS: Media Scheduler step tracking is undefined
38372		MDS: Media Scheduler <Operation Sequence Type> operation <Media Instance ID> has reached its maximum step count <Maximum Step Count> for step Id <Step Id> (process Id<Process Id>)
38373		MDS: Media Scheduler <Operation Sequence Type> operation <Media Instance ID> has an undefined process
38374		MDS: Media Scheduler <Operation Sequence Type> operation <Media Instance ID> could not start a new process (maximum of <Max process count>)
38375		MDS: Media Scheduler <Operation Sequence Type> operation <Media Instance ID> could not find process <Process Id>
38376		MDS: Media Scheduler could not finish sequence scan, too many steps (maximum <Maximum number of scan steps>)
38377		MDS: Media Scheduler could not schedule bay close since the bay is not open
38378		MDS: Media Scheduler could not schedule bay close since one was already scheduled
38379		MDS: Media Scheduler decision type is not supported for step type
38380		MDS: Too many alternate bays, maximum is <Maximum number of alternative bays>
38381		MDS: The media type '<Media name>' is not currently allowed on this device
38400		NET: TRECK TCP/IP Stack is reporting a Fatal Error condition
38401		NET: Failure to activate SLIP link-layer protocol
38402		NET: Failure to activate PPP Server link-layer protocol
38403		NET: Failure to activate PPP Client link-layer protocol
38404		NET: Failure to activate EtherNet link-layer protocol
38405		NET: Failure to allocate internal memory - FATAL
38406		NET: Failure to add a device driver to TRECK TCP/IP Stack - FATAL
38407		NET: Failure to open a device driver for the TRECK TCP/IP Stack - FATAL
38408		NET: Interface device driver for the TRECK TCP/IP Stack is not open
38409		NET: Failure to query information about a h/w interface in the TRECK TCP/IP Stack - FATAL
38410		NET: Warning in TRECK function <Function name>: <Warning description>\n
38601		STP: Unable to write velocity, not in Host Velocity Control Mode
38602		STP: Attempt to read or write an invalid parameter
38603		STP: Attempt to write an invalid configuration flag
38604		STP: Attempt to write an invalid configuration mode
38605		STP: Attempt to write a stepper motor parameter that is out of range
38606		STP: Attempt to change the parameters of the system while the motor is moving
38607		STP: Trajectory queue address out of range
38608		STP: Motor does not exist on this board
38609		STP: Stepper hardware status check has failed
38610		STP: The Stepper Firmware has not been properly initialized
38611		STP: Stepper controller is awaiting an unsolicited message acknowledge
38800		WMD: Out of command/prompt/stream handles
38801		WMD: Invalid handle
38802		WMD: Internal error detected
38803		WMD: Solicitor number is currently used
38804		WMD: Command Table Full
38805		WMD: Prompt Descriptor Table Full
38806		WMD: Too many buttons for prompt
38807		WMD: An invalid button code was used
38808		WMD: An invalid prompt ID was used
38809		WMD: Illegal attempt to access prompt object
38810		WMD: Unsupported Workstation protocol
38811		WMD: Device is running\nUNSUPPORTED\nEngineering Firmware
38812		WMD: Invalid Command Code detected
38813		WMD: socket() call has failed
38814		WMD: bind() call has failed
38815		WMD: listen() call has failed
38816		WMD: accept() call has failed
38817		WMD: recv() call has failed
38818		WMD: send() call has failed
38819		WMD: WSAStartup() call has failed
38820		WMD: ioctlsocket() call has failed
38821		WMD: Command is rejected because of service lockout
38822		WMD: Service lockout
38823		WMD: No socket connection with workstation.
38824		WMD: Invalid data unit size RCON parameter in Read Memory or Write Memory command
38825		WMD: Too many workstation status change callbacks have been registered
38826		WMD: The RCON connection to the workstation has been lost
38827		WMD: Workstation is not detected
38828		WMD: Too many workstation command received callbacks have been registered
39000		SAT: The board type is unknown
39101		SIF: SIF/SCON General Failure
39102		SIF: Received an SCON NAK reply
39103		SIF: SCON Operation timed out
39104		SIF: No Free CAN Transmit Buffers available
39105		SIF: The SIF Subsystem has detected a reentrancy attempt
39106		SIF: The SIF Subsystem has not been initialized properly
39107		SIF: The SIF Subsystem has run out of queue buffers
39108		SIF: SIF Serial port Open has failed due to not being activated for SIF serial support
39301		SIO: SIO General Failure
39302		SIO: Failure to Register with SIF
39303		SIO: SAT I/O Node does not exist
39304		SIO: The Unsolicited Callback Information Block has Become Corrupted
39305		SIO: The Call Back Function Specified is Invalid
39306		SIO: Attempt to register too many callbacks with the SIO subsystem
39307		SIO: All SCON Connection resources are in use - no more left
39400		GIM: Invalid Image ID
39402		GIM: Internal firmware error
39403		GIM: Invalid Image Parameter
39404		GIM: Please load a new plate
39405		GIM: Please unload the ejected media
39406		GIM: Required data was locked by another subsystem
39407		GIM: Not ready for Flush End command
39408		GIM: No flush active that can be ended.
39409		GIM: Invalid Flush state detected
39410		GIM: Device is unlocked
39411		GIM: Head not initialized: not ready for query
39412		GIM: Unrecoverable Flush Failure. Device must be reset.
39413		GIM: Invalid Image Task ID detected
39414		GIM: Invalid bay number detected
39415		GIM: WARNING: Bypassed functionality detected
39417		GIM: Carriage command received while carriage is busy
39418		GIM: Invalid carriage velocity value attempted
39419		GIM: Invalid carriage position value attempted
39420		GIM: Invalid latch number
39421		GIM: Invalid sensor number
39422		GIM: Invalid latch value code
39424		GIM: Unexpected Command
39427		GIM: Flush is required before operation permitted.
39430		GIM: Invalid Group ID
39432		GIM: Too many images in Group
39433		GIM: No group available
39434		GIM: The device cannot support the number of stacks queried
39435		GIM: Suspend queue is full, cannot handle any more suspends
39436		GIM: Suspend could not be found, not removed
39437		GIM: Please load carrier
39438		GIM: Please unload the ejected carrier
39439		GIM: Invalid group parameter
39440		GIM: Please load receiver
39441		GIM: Please load donor
39442		GIM: RCON command is missing argument '<Name of the missing parameter name>'
39443		GIM: Invalid RCON variable argument specified '<Name of the invalid argument name>'
39444		GIM: Unknown or invalid property ID specified
39445		GIM: Invalid operation attempted on property '<Name of the DCAPI property could not be manipulated>'
39448		GIM: RCON media instance is unknown or invalid
39449		GIM: The system is attempting to simultaneously access too many media instances
39450		GIM: No media is available. Requested media operation cannot be performed.
39451		GIM: Property Not supported
39452		GIM: Invalid arguments specified in Set Seam Geometry request
39453		GIM: Prompt array full, cannot make new prompt
39454		GIM: Could not find prompt
39455		GIM: Workstation command locked out
39457		GIM: Invalid or unsupported combination of arguments
39458		GIM: Service move command received while device is processing a previous move command
39459		GIM: The imaged area is not yet available for reading
39461		GIM: Please load a new plate on the home side
39462		GIM: Please load a new plate on the away side
39463		GIM: Please load a new plate in the center
39464		GIM: Please load two new plates
39465		GIM: Status Handler table full
39466		GIM: Workstation watchdog timed out. Shutting down all systems.
39469		GIM: Bay media configurations must match for transfer
39471		GIM: Invalid arguments specified in Set Punch Regions request
39472		GIM: Not enough free Media Handler descriptors to start a new Media Handler operation
39473		GIM: Media Handler operation specified could not be found
39501		IOS: software error
39502		IOS: Insufficient memory to create IO scanner tables
39503		IOS: I/O Bit not found in product table
39504		IOS: I/O Group not found in product table
39505		IOS: Event group pointer is null
39506		IOS: Can't assign non-input bit to event group
39507		IOS: IO values are not initialized
39508		IOS: Bypass not allowed on this I/O
39509		IOS: No remote address for requested bit
39510		IOS: No remote address for requested bit
39511		IOS: Invalid IOS mode
39512		IOS: IO Name Identifier too long
39513		IOS: Incorrect number of IO Data bytes
39514		IOS: Workstation command locked out
39515		IOS: Conversion function not available
39516		IOS: Callback table full
39517		IOS: Bit handle already has an event registered
39518		IOS: Satellite board address <The satellite board ID that is not responding> register <The register address being accessed> not responding
39519		IOS: TCP/IP failure
39800		SST: Invalid API Function Parameter Detected
39801		SST: Internal SST error
39802		SST: Invalid SST handle
39803		SST: Status group not registered
39804		SST: Invalid SST I/O type
39805		SST: Specified I/O not found
39806		SST: Invalid upper and lower thresholds for analog I/O
39807		SST: Invalid digital target value
39808		SST: Invalid I/O failure priority level
39809		SST: System is not in initialization mode
39900		MBT: Fatal Error - Fell out of Monitor code
39901		MBT: Fatal Error - Boot Code is Corrupt
39902		MBT: Fatal Error - Insufficient Heap Memory available
40001		SMC: Software error
40002		SMC: CAN communication error
40003		SMC: Cannot issue command, motor is moving [<Name of the stepper motor>]
40004		SMC: Cannot issue command, motor is being controlled by another process and is reserved [<Name of the stepper motor>]
40005		SMC: Motor number out of range or the motor is not configured on this device
40006		SMC: Invalid trajectory queue address specified [<Name of the stepper motor>]
40007		SMC: Invalid parameter specified [<Name of the stepper motor>]
40008		SMC: Invalid velocity value specified [<Name of the stepper motor>]
40009		SMC: Invalid acceleration value specified [<Name of the stepper motor>]
40010		SMC: Invalid micro step rate specified [<Name of the stepper motor>]
40011		SMC: Invalid current specified [<Name of the stepper motor>]
40012		SMC: Invalid direction mode parameter specified [<Name of the stepper motor>]
40013		SMC: Remote hardware is not processing motor commands [<Name of the stepper motor>]
40014		SMC: Stepper motor name not found
40015		SMC: Motor unexpectedly hit the home sensor [<Name of the stepper motor>]
40016		SMC: Motor unexpectedly hit the away sensor [<Name of the stepper motor>]
40017		SMC: Stepper command timed out [<Name of the stepper motor>]
40018		SMC: The remote board hardware status check has failed [<Name of the stepper motor>]
40019		SMC: Invalid motor gain parameter specified [<Name of the stepper motor>]
40020		SMC: Motor initialization has failed [<Name of the stepper motor>]
40021		SMC: Remote motor has not been initialized [<Name of the stepper motor>]
40022		SMC: Invalid update mode parameter specified [<Name of the stepper motor>]
40023		SMC: Invalid position specified [<Name of the stepper motor>]
40024		SMC: Invalid steps per real unit specified [<Name of the stepper motor>]
40025		SMC: Invalid distance specified [<Name of the stepper motor>]
40026		SMC: Invalid initialization parameters specified [<Name of the stepper motor>]
40027		SMC: Command failed, the shared motor is using all the remote bandwidth [<Name of the stepper motor>]
40028		SMC: Invalid initialization dual stepper mode specified [<Name of the stepper motor>]
40029		SMC: Move command preempted
40030		SMC: Failed to detect 48V [<Name of the stepper motor>]
40031		SMC: Failed to detect alternate sensor cable [<Name of the stepper motor>]
40032		SMC: Failed to detect home and away cable [<Name of the stepper motor>]
40033		SMC: Failed to detect power cable [<Name of the stepper motor>]
40034		SMC: Failed to detect data cable [<Name of the stepper motor>]
40035		SMC: Over current fault detected [<Name of the stepper motor>]
40036		SMC: Over temperature fault detected [<Name of the stepper motor>]
40037		SMC: Under voltage fault detected [<Name of the stepper motor>]
40038		SMC: Driver fault detected [<Name of the stepper motor>]
40039		SMC: Failed to detect the cable [<Name of the stepper motor>]
40040		SMC: Brake override detected [<Name of the stepper motor>]
40041		SMC: Invalid maximum jerk value specified [<Name of the stepper motor>]
40042		SMC: Input value is outside the limits [<Name of the stepper motor>]
40043		SMC: Satellite board has reset, stepper control has failed [<Name of the stepper motor>]
40044		SMC: Velocity of <Velocity specified in real units/s> units/s [<Velocity specified in steps/s> steps/s] is too high, max is <Maximum velocity allowed in real units/s> units/s [<Maximum velocity allowed in steps/s> steps/s] [<Name of the stepper motor>]
40045		SMC: Velocity of <Velocity specified in real units/s> units/s [<Velocity specified in steps/s> steps/s]is too low, min is <Minimum velocity allowed in real units/s> units/s [<Minimum velocity allowed in steps/s> steps/s] [<Name of the stepper motor>]
40046		SMC: Motor already has a reset callback [<Name of the stepper motor>]
40047		SMC: Satellite board does not support quarter current mode [<Name of the stepper motor>]
40048		SMC: The motor has been stopped before the motor has started [<Name of the stepper motor>]
40049		SMC: Remote motor is waiting for an acknowledge [<Name of the stepper motor>]
40050		SMC: Remote motor has failed with an undefined error <The undefined error> [<Name of the stepper motor>]
40100		SBT: Fatal Error - Fell out of Monitor code
40101		SBT: Fatal Error - Boot Code is Corrupt
40102		SBT: Fatal Error - Insufficient Heap Memory available
40103		SBT: Fatal Error - Failure Registering VR Handler with SIF
40104		SBT: Fatal Error - Failure Registering Broadcast Handler with SIF
40105		SBT: Warning - Failure to Erase a Flash Sector
40200		MDH: <motor name> stepper motor has already started the command, cannot start it again
40201		MDH: Software error. Media Handler error occurred, but error has no error code.
40202		MDH: Software error. Suspend received a invalid suspend button type.
40203		MDH: Software error. Media Handler received an unrecognized command.
40206		MDH: Command Failed. Media Handler already running another task.
40207		MDH: Cannot cancel command. Media Handler task is not currently executing any commands.
40208		MDH: Media handler task is currently suspended.
40209		MDH: Media handler is not currently suspended.
40212		MDH: Media Handler task cancelled
40213		MDH: Media released from the drum and removed from the machine.
40214		MDH: Forced failure.
40216		MDH: Cannot enable/disable cycletest mode when machine not idle.
40217		MDH: Cannot enable/disable 'plateless' operation when machine not idle.
40228		MDH: Media Handler task aborted
40230		MDH: Invalid actuator timeout (must be non-zero)
40231		MDH: <motor name> stepper motor cannot search for a sensor [<I/O name>] if waiting is not specified
40237		MDH: <motor name> stepper motor recieved an invalid setup parameter
40238		MDH: <motor name> stepper motor has not started a command, cannot wait for it to complete
40239		MDH: Software Error. The error code contains the wrong number of parameters
40240		MDH: Fatal error
40242		MDH: Could not set the media on the drum
40243		MDH: <motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]
40244		MDH: Stepper motor cannot search for a sensor that has been disabled [<I/O name>]
40245		MDH: Command cannot be cancelled
40246		MDH: Media released, remove media and use MEDIA REMOVED to continue
40251		MDH: Media Handler does not support simulation option <Option>
40254		MDH: Media handler sequence attempted to use auto-retry on step that pointed to a different step
40257		MDH: Software error. Wrong or invalid argument supplied
40258		MDH: Could not find step '<Step description>' in sequence
40259		MDH: <Motor name> stepper motor did not reach the sensor it was searching for [<I/O name>]
40267		MDH: <Motor name> stepper motor unexpectedly hit the home sensor
40275		MDH: <Motor name> stepper motor unexpectedly hit the away sensor
40283		MDH: <Motor name> stepper motor failed to respond
40292		MDH: The Media Handler experienced an internal error, restart the device
40293		MDH: <motor name> stepper motor has not completed previous command
40294		MDH: <motor name> stepper motor sensor mask(s) are setup but motor is not setup to wait for completion
40295		MDH: Operation failed, but no error setup (device actuate)
40296		MDH: <motor name> stepper motor waited for <timeout in seconds> seconds, but setup command did not complete
40297		MDH: <sequence type> (<sequence id>) sequence is not available with these arguments
40298		MDH: <sequence type> (<sequence id>) sequence is not supported on this device
40301		MDH: Invalid bay number (bay #<Bay number>) selected
40302		MDH: No plates detected in bay <Bay number>
40303		MDH: No plates detected on plate buffer table
40341		MDH: Bay <loader bay number> is not accessible because the preloader is docked
40342		MDH: Cannot move the bay hardware, it has not been initialized
40343		MDH: The plate cover must be open for the preloader
40344		MDH: Undock the preloader and remove the plate(s) from the bay, then dock the preloader again
40345		MDH: Please remove plate(s) from the outer bay [<I/O name>]
40346		MDH: The plate stack is too high to deploy the outer bay arms
40401		MDH: Picker up/down timeout: Failed to <Action> sensor. [<I/O name>]
40402		MDH: Picker in/out timeout: Failed to <Action> sensor. [<I/O name>]
40403		MDH: Picker wrist timeout: Failed to <Action> sensor. [<I/O name>]
40404		MDH: Picker vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]
40405		MDH: Cannot move the picker, it has not been initialized
40406		MDH: Plate not detected on picker
40407		MDH: Please remove plate detected on picker
40408		MDH: Please close plate cover
40409		MDH: Cannot move picker <Direction> because <Obstruction>
40410		MDH: Plates are sticking together. Please open the plate cover and separate the plates. Press RESUME to continue.
40411		MDH: Timeout waiting for plate cover to be opened/closed. Command cancelled
40412		MDH: Device ready. Close plate cover to continue.
40413		MDH: Picker wrist sensor is not working
40414		MDH: Picker wrist cylinder is faulty
40415		MDH: Separator arm timeout: Failed to <Action> sensor. [<I/O name>]
40416		MDH: Cannot move separators <Direction> because <Obstruction>
40417		MDH: Please close plate cover, or put the preloader into position
40420		MDH: The Preloader is in a faulted state. Please check the Preloader display for more information
40421		MDH: The Preloader is not ready. It may be out of position, open, or not fully powered on
40423		MDH: The Preloader is not powered on. Please check the Preloader connections
40424		MDH: The Preloader is in the bay. Please check the Preloader display for more information
40425		MDH: The Preloader is not loading plates properly into the Trendsetter bay. Please check the Preloader display for more information
40426		MDH: No plates detected in the bay. The plate may not have been properly loaded by the Preloader
40428		MDH: Loader exit door timeout: Failed to <Action> sensor. [<I/O name>]
40429		MDH: Picker cups in/out timeout: Failed to <Action> sensor. [<I/O name>]
40430		MDH: Cannot open exit door because an unpicked plate is detected. Please remove all plates from the plate buffer load table.
40450		MDH: Picker up/down timeout: Failed to <Action> sensor. [<I/O name>]
40466		MDH: Picker was expected to be down and out but was not
40467		MDH: Exit door was expected to be closed but was not
40607		MDH: Clamps expected to be on the trailing edge backbone, but they were not detected
40608		MDH: Clamps detected on the trailing edge backbone, but they were not expected
40616		MDH: Roller timeout: Failed to <Action> sensor. [<I/O name>]
40622		MDH: LEC down preventing roller move down
40624		MDH: Media being loaded has been measured to have an unexpected main scan length
40625		MDH: Media being loaded has an invalid mainscan length, min=<Minimum mainscan length in mm> mm, max=<Maximum mainscan length in mm> mm
40626		MDH: Media being loaded has an invalid subscan length, min=<Minimum mainscan length in mm> mm, max=<Maximum mainscan length in mm> mm
40629		MDH: Media partially loaded on drum, use RELEASE then remove the media
40630		MDH: Media fully on drum
40632		MDH: Media flyoff detected, please open panel and remove media
40634		MDH: Media is expected on the drum, but no media was found
40635		MDH: Cannot execute command because the drum is moving
40636		MDH: Drum not at the expected position, position may have shifted because of outside interaction
40638		MDH: Drum not initialized, use 'drum init' to initialize
40652		MDH: Cannot calibrate (media size measurement sensor bypassed)
40663		MDH: Leading edge clamp timeout: Failed to <Action> sensor. [<I/O name>]
40664		MDH: Trailing edge backbone timeout: Failed to <Action> sensor. [<I/O name>]
40665		MDH: Trailing edge clamp lock/unlock timeout: Failed to <Action> sensor. [<I/O name>]
40666		MDH: Exit door timeout: Failed to <Action> sensor. [<I/O name>]
40667		MDH: Load ramp timeout: Failed to <Action> sensor. [<I/O name>]
40668		MDH: Please remove media detected on load ramp
40669		MDH: Media not detected on load ramp
40670		MDH: Please move clamps to park position, then select RESUME
40684		MDH: Roller is down, cannot move LEC
40692		MDH: Engine is currently busy, cannot change drum state
40712		MDH: Cannot execute command because LEC is not down
40713		MDH: Cannot execute command because TEC is not down and locked to clamps
40722		MDH: Stack locations (<Bit-field of the locations>) are not valid media positions
40725		MDH: Invalid stack count and rotate flag combination
40728		MDH: Media is too <Limit type> to rotate, limit is <Limit amount> mm
40740		MDH: TEC adjust <Current TEC adjust> is too small for this plate size, should be at least <Recommended TEC adjust>
40741		MDH: Trailing edge clamp position invalid - load calibration required
40742		MDH: Media has invalid main scan length <MeasuredLength> mm, it is smaller than expected <ExpectedLength> mm
40743		MDH: Media has invalid main scan length <MeasuredLength> mm, it is larger than expected <ExpectedLength> mm
40744		MDH: Media has invalid main scan length, it is larger than expected <ExpectedLength> mm
40745		MDH: Media with a subscan size of <SubscanSize> cannot be loaded at location '<Location>'
40801		MDH: Unload table up/down timeout: Failed to <Action> sensor. [<I/O name>]
40802		MDH: Unload table cups up/down timeout: Failed to <Action> sensor. [<I/O name>]
40803		MDH: Unload table vacuum timeout: Failed to achieve vacuum threshold (<Threshold>) within <Timeout> ms (only reached <ActualValue>). [<I/O name>]
40804		MDH: Cannot move the unload table, it has not been initialized
40805		MDH: Timeout waiting for plate to leave unload table
40806		MDH: Unload cups rotated, cannot move unload table cups
40807		MDH: Unload stepper motor not in safe position to rotate cups
40809		MDH: Please remove plate detected on unload table [<I/O name>]
40810		MDH: Rotator timeout: Failed to <Action> sensor. [<I/O name>]
40811		MDH: Unable to pull media out of engine. Media still detected at entry sensor [<I/O name>]
40812		MDH: Media not detected at unload table entry [<I/O name>]
40813		MDH: Invalid exit number (exit #<Exit number>) selected
40814		MDH: The processor is not ready to accept plates
40815		MDH: The processor is in a faulted state
40816		MDH: The processor is still busy with the previous plate, so is unable to accept another
40822		MDH: The rotate option is not available on this device
40825		MDH: Workstation cannot connect to the PMI.\nPress RESUME when the processor is ready to accept the next plate
40936		MDH: Drum vacuum timeout: Failed to fall below vacuum threshold (<Threshold> kPa) within <Timeout> sec (only reached <ActualValue> kPa). [<I/O name>]
41500		OWB: Internal Error - 1-Wire-Bus response buffer became full
41501		OWB: OWB General Failure
41502		OWB: The 1-Wire-Bus appears to be shorted.
41503		OWB: An Alarm presence pulse was found on the 1-Wire-Bus.
41504		OWB: No node presence pulse was found on the 1-Wire-Bus.
41505		OWB: The 1-Wire-Bus adapter (DS1411) is not responding.
41506		OWB: Bad CRC received from a Node ID on the 1-Wire-Bus.
41507		OWB: Write Data failed to verify from a Node on the 1-Wire-Bus.
41514		OWB: No more Nodes on the 1-Wire-Bus.
41800		IBM: General Failure
41801		IBM: Invalid iButton Scanner data point handle
41802		IBM: Cannot write to an iButton handle that is a READ value
41803		IBM: Could not find the requested iButton handle
41804		IBM: iButton Manager (IBM) is not initialized
41805		IBM: The requested iButton handle is not available
42900		PST: POST: <Test Code> - <Test Description>
42901		PST: No response received from <Satellite Board>
42902		PST: Unknown satellite board (ID=<Satellite ID>) found
42903		PST: Invalid mode parameter in RCON command Get Post Result
42999		PST: Machine Electronics FAILED Power On Self-Tests
43001		DEB: Debris removal software error: <Software error>
43002		DEB: Particulate Only Collection (POC) debris removal is not enabled on this device
43003		DEB: Particulate and Chemical Collection (PACC) debris removal is not enabled on this device
43004		DEB: The air jet is enabled, but not turned on
43005		DEB: The blower is not turned on
43006		DEB: The flow rate is below the minimum required
43007		DEB: The cabinet has lost power
43008		DEB: The particulate filter is not present or upside down, the lid is not closed, or the data cable is disconnected
43009		DEB: The particulate filter is almost full. Please ensure a replacement filter is on hand
43010		DEB: The particulate filter is full. You must replace the particulate filter to continue imaging
43011		DEB: The debris collection nozzle is blocked
43012		DEB: The debris hose is disconnected
43013		DEB: There is a problem with one or more of the pressure sensors in the debris removal cabinet
43014		DEB: The debris hose is disconnected, the cabinet has lost power, or the cabinet lid is not latched properly
43015		DEB: There may be a partial blockage of the collection nozzle, or a leak, but the flow rate is still above minimum
43016		DEB: There is a partial blockage of the collection nozzle, or a leak, and the flow rate is below minimum
43017		DEB: The media being imaged releases potentially harmful emissions. See the Operator Manual for more information
43018		DEB: The debris removal chemical filter is not present
43019		DEB: The chemical filter has almost expired. Please ensure a replacement filter is on hand
43020		DEB: The chemical filter has expired. You must replace the chemical filter and reset the output device to continue imaging
43021		DEB: The chemical filter usage sensor is corrupt or the chemical filter was changed and the output device was not reset
43022		DEB: Unable to communicate with the chemical filter. See the Operator Manual for more information
43023		DEB: The chemical filter usage calculated is negative
43024		DEB: Unable to calibrate <Sensor Name> pressure sensor
43025		DEB: Unable to communicate with the chemical filter during initialization. See the Operator Manual for more information
43026		DEB: Timeout: the pressure sensor output failed to stabilize
43027		DEB: No debris removal options are enabled on this device
43028		DEB: There is a problem with the nozzle pressure sensor in the output device
43029		DEB: Command failed: cannot run more than one PACC option at a time
43030		DEB: Cannot start new debris option while another is in an error condition
43031		DEB: The chemical filter installed is not suitable for the selected media
43032		DEB: The particulate filter is almost full AND the chemical filter has almost expired
43033		DEB: Cannot setup ibutton: <IButton Parameter>
43034		DEB: Chemical filter iButton already has valid usage information, did not reprogram
43035		DEB: Conversion failed.
43301		CRG: software error
43302		CRG: Carriage initialization timed out <Initialization operation>
43303		CRG: Carriage is reserved, command ignored
43304		CRG: The current carriage command has been preempted
43305		CRG: Carriage Hardware Fault: <Description of the faulted hardware component>
43306		CRG: Requested carriage velocity too high, recommended max = <Recommended maximum carriage velocity> mm/sec
43307		CRG: Carriage Accel requires Ispeed, Mspeed or velocity in range +/- <Maximum carriage velocity using current acceleration value> mm/s
43308		CRG: Carriage travel limit (<Text string describing which limits signals are active as follows>) unexpectedly hit
43309		CRG: Carriage velocity exceeds register size
43310		CRG: Carriage has aborted plotting
43311		CRG: Carriage can not reach requested position
43312		CRG: Carriage Amplifier fault: <Text string describing specific amplifier fault>
43313		CRG: Carriage currently initializing
43314		CRG: Carriage not initialized
43500		DF1: internal memory allocation error - DF1 Driver
43501		DF1: failure to open to the URT Subsystem - DF1 Driver
43601		MOP: MOP Initialization failed
43602		MOP: Argument name not found or used token in place of argument
43603		MOP: MOP API() function can only be used with optional tokens
43604		MOP: Internal MOP firmware error
43605		MOP: Unregistered MOP commands or MOP commands registered twice
43606		MOP: An invalid MOP access level was selected
43701		ZAD: Could not read the Z-Drive parameters
43702		ZAD: Command not expected at this time
43703		ZAD: Internal firmware error
43704		ZAD: Command was aborted
43705		ZAD: Error sending SMC motor command
43706		ZAD: Zdrive stopped by external command
43707		ZAD: Zdrive not initialized, position is unknown
43708		ZAD: Zdrive motor could not be initialized, zdrive cannot be used
43709		ZAD: Zdrive is busy
43710		ZAD: Zdrive is busy trying to abort
43711		ZAD: Zdrive is busy trying to stop
43712		ZAD: Zdrive is in invalid state
43713		ZAD: Zdrive received an invalid message
43714		ZAD: Zdrive invalid internal structure
43715		ZAD: Zdrive received an invalid state message
43716		ZAD: Zdrive received an invalid message type
43717		ZAD: Zdrive received an invalid message code
43718		ZAD: Zdrive requires SMC version <SMC Version major>.<SMC Version minor>
43802		ZAC: Another z axis sequence is currently being processed
43803		ZAC: Internal: Invalid parameter passed to function
43804		ZAC: Internal: System resource unavailable
43805		ZAC: Focus Error value requested while focus out of range or saturated
43806		ZAC: Z Axis Focus routine aborted by monitor command
43807		ZAC: Media not found by Z axis, confirm dimensions
43808		ZAC: Media not found by Z axis, confirm dimensions
43809		ZAC: Head operation timed out
43810		ZAC: Media not found by Z axis due to head collision, confirm dimensions
43811		ZAC: Eccentric media surface: Probable cause out-of-round cylinder / bad mount
43900		CTP: CTP Engine Component is not present - internal firmware error
43901		CTP: CTP Processor Connected to Device
43902		CTP: CTP Processor Not Enabled
43903		CTP: Load or unload method not supported
43904		CTP: Lost communication with the slave board
43905		CTP: Master/slave operation timed out
44201		DTL: Non-head type message sent to DTL Driver
44202		DTL: DTL Driver unable to determine message type
44203		DTL: DTL Driver: invalid logical channel number
44204		DTL: DTL head communication sync lost
44205		DTL: DTL communication port not open
44206		DTL: Timeout attempting to close communication port
44207		DTL: DTL Server received a packet bigger than allowed
44208		DTL: DTL Server received a packet containing an illegal command
44209		DTL: DTL server or client failed to establish a TCP/IP connection
44210		DTL: TCP socket is shut down locally or remotely
44211		DTL: Internal error of TCP protocol
44212		DTL: TCP socket create failure
44213		DTL: TCP socket connect failure
44214		DTL: TCP protocol received an invalid packet
44215		DTL: TCP protocol link is not ready
44300		CEH: Error Code [<Error code>] <Error string>
44301		CEH: Warning Fault [<Error code>] <Error string>
44302		CEH: Fatal Fault [<Error code>] <Error string>
44303		CEH: The write laser request is in progress
44304		CEH: The stroke calibration is in progress
44305		CEH: The focus request is in progress
44306		CEH: The requested media is not supported by the exposure head
44307		CEH: An upgrade of the host firmware is recommended
44308		CEH: An upgrade of the exposure head firmware is recommended
44309		CEH: An upgrade of the host firmware is required
44310		CEH: An upgrade of the exposure head firmware is required
44311		CEH: The requested functionality is not supported by the exposure head
44401		BOS: BOS subsystem not initialized - cannot proceed.
44402		BOS: The requested update rate for the BOS subsystem is less than 50 ms
44403		BOS: Error creating BOS group: Output bit already used elsewhere
44404		BOS: Error creating BOS group: Too many outputs in group, max is 15
44405		BOS: BOS Handle specified is invalid, cannot process action
44406		BOS: New state for BOS group is invalid, cannot update group state.
44407		BOS: BOS has run out of empty groups and so cannot create a new one.
44408		BOS: BOS timed out trying to find a handle for a new group.
44500		EHI: The exposure head is offline
44501		EHI: The exposure head is being initialized
44502		EHI: The exposure head has failed
44503		EHI: The exposure head is in programming mode
44504		EHI: The exposure head has been disabled
44505		EHI: Head command transporter is not open
44506		EHI: Head command transporter failure
44507		EHI: The response / unsolicited packet is invalid
44508		EHI: The response / unsolicited packet length is invalid
44509		EHI: The response / unsolicited packet protocol is invalid
44510		EHI: The unsolicited packet is not supported
44511		EHI: The exposure head control mode is invalid
44512		EHI: The exposure head type is invalid
44513		EHI: The exposure head control mode transition is invalid
44514		EHI: The exposure head has unexpectedly reset
44515		EHI: The baud rate negotiation algorithm has failed
44516		EHI: The application protocol negotiation algorithm has failed
44517		EHI: The command packet is not supported
44518		EHI: The exposure head is not supported
44519		EHI: Baud rate negotiation is not supported by the exposure head
44520		EHI: Application protocol negotiation is not supported by the exposure head
44521		EHI: The error string cannot be determined; the exposure head type is unknown
44522		EHI: The error string could not be retrieved from the exposure head
44523		EHI: The functionality is not supported
44524		EHI: Monitor redirection is not supported
44525		EHI: A parameter is invalid
44526		EHI: EHI port closed before head commands complete
44527		EHI: Command response from exposure head took too long
44528		EHI: Response from head incorrectly sequenced
44529		EHI: Parameter load already in progress
44530		EHI: Specified parameter group unknown
44531		EHI: Changed parameter unknown in thermal head
44532		EHI: The monitor command requires the exposure head to be online
44533		EHI: The monitor command requires application protocol 0
44534		EHI: The monitor command requires a Thermal 1.0 or Thermal 1.7x exposure head
44535		EHI: The monitor command requires a Tfx or Thermal 2 exposure head
44536		EHI: The Thermal 1.0 or Thermal 1.7x exposure head was unable to learn focus
44537		EHI: Timeout waiting for the focus
44538		EHI: Timeout waiting for the write laser
44539		EHI: The firmware version of the exposure head is not supported
44540		EHI: Unexpected software failure
44541		EHI: Head Command Transaction Buffer Overflow
44542		EHI: Head Media Data Block format is unsupported
44543		EHI: Timeout during head redirection access attempt
44544		EHI: Parameter access buffer overrun attempted
44545		EHI: The redirected command to the head failed
44546		EHI: The Media Data Block is missing data
44547		EHI: The head has requested to be powered down
44600		MPI: Carrier not loaded or specified Proof Index is out of range
44601		MPI: Invalid proof type
44602		MPI: Invalid proof border types
44603		MPI: No more media supported
44604		MPI: Media Image Mode ID out of range: <MIMID>
44605		MPI: Media matching MIMID not found
44606		MPI: Corrupted internal value detected
44607		MPI: Internal firmware failure
44608		MPI: MPI subsystem not initialized.
44609		MPI: Exposure head not available.
44610		MPI: Media name is blank or invalid
44611		MPI: Head operation timed out
44612		MPI: Invalid or unrecognized Media Data Block
44613		MPI: Media index out of range: <Media index>
44614		MPI: Buffer overflow
44615		MPI: MIMID <MIMID> already in use by slot <Slot Number>
44800		EHI: no error
44801		EHI: temperature out of range
44802		EHI: value out of range
44803		EHI: missing laser on parameters
44804		EHI: attempted write blocked
44805		EHI: failure to write to memory
44806		EHI: unsupported message
44807		EHI: message length incorrect
44808		EHI: invalid control message
44809		EHI: operation was aborted
44832		EHI: no more room in mailbox
44833		EHI: ran out of buffers
44834		EHI: all retries failed on chnl 0
44835		EHI: all retries failed on chnl 1
44836		EHI: sync lost on chnl 0
44837		EHI: sync lost on chnl 1
44848		EHI: CONFIG register incorrect
44849		EHI: flash memory checksum error
44850		EHI: LCA won't init for reprogram
44851		EHI: LCA won't admit being loaded
44852		EHI: SRAM memory check failure
44896		EHI: software error
44897		EHI: LCA config unavailable
44898		EHI: LCA not found
44899		EHI: hardware timeout
44946		EHI: WLC PCB overheated, reset head
44947		EHI: Laser drive current limit
44948		EHI: Laser safety interlock is open
44949		EHI: DTD laser diode over temperature
44950		EHI: DTD laser diode over voltage
44951		EHI: DTD laser diode over current
44952		EHI: DTD +24V supply low
44953		EHI: DTD +24V supply high
44954		EHI: DTD +15V supply low
44955		EHI: DTD temperature sensor open circuit
44956		EHI: DTD software timeout
44957		EHI: DTD reset asserted
44958		EHI: DTD temperature below set point
44959		EHI: DTD temperature above set point
44960		EHI: shutter disabled
44961		EHI: reset detected
44962		EHI: laser disabled
44963		EHI: focus not initialized: Execute 'focus init'
44964		EHI: focus error detected at <Subscan location> mm <Relative location> while imaging, check plate for artifacts
44965		EHI: laser shutdown detected
44966		EHI: head case over temperature, <Case temperature> C
44967		EHI: head ambient over temperature, <Ambient temperature> C
44968		EHI: media <Media number> not found in HDM nvs subsystem
44969		EHI: crash detected, error code = 0x<Error code>
44970		EHI: Warning - head temperature high, <Case temperature> C
44971		EHI: SCORR out of range
44972		EHI: checksum error in <NVS subsystem> calibration block
44973		EHI: checksum error in <NVS subsystem> configuration block
44974		EHI: newline error, check drum encoder and LC-BP cable
44975		EHI: media thickness out of range
44976		EHI: EH-PHI cbl. (hotlink fault)
44977		EHI: LV 24V not in range (unipolar)
44978		EHI: LV 24V or High voltage fault
44979		EHI: LV Over temperature
44980		EHI: LV Too much stray light for beam balance
44981		EHI: LV Negative 12V fault (unipolar)
44982		EHI: LV Bias current fault (unipolar)
44983		EHI: Recalibration is on
44984		EHI: Recalibration fault
44985		EHI: checksum error in stroke correction download
44986		EHI: LV Not enough light for beam balance
44987		EHI: stroke clock frequency invalid, aborting download
44988		EHI: DTD status unstable
44989		EHI: Laser sampling disabled (wsample == 0)
44990		EHI: Beam position sampling disabled (bsample == 0)
44991		EHI: Focus sampling disabled (fsample == 0)
44992		EHI: Light level too low for Beam Pointing
44993		EHI: Timeout waiting for LASER OK
44994		EHI: Light valve high voltage fault
44995		EHI: LV Positive 12V fault (bipolar)
44996		EHI: Stroke Clock or Imaging signal fault, check LC-BP cable
44997		EHI: Focus sensor fails linearity test, check head position
44998		EHI: Laser safety loop has just been closed
44999		EHI: Laser safety loop has just opened
45000		EHI: Only the safety loop detected by the head has closed
45001		EHI: Only the safety loop detected by the laser has closed
45008		EHI: executive call tsk_create() failed
45009		EHI: all tasks suspended
45010		EHI: executive call mbx_create() failed
45011		EHI: executive call mbx_send() failed
45012		EHI: executive call buf_alloc() failed
45013		EHI: executive call tmr_create() failed
45014		EHI: Task received message that was not sent
45015		EHI: Task sending message owned by another task
45016		EHI: Task sending unreserved message
45017		EHI: message buffer request failed
45018		EHI: Reserved message in message pool
45019		EHI: Task releasing message owned by another task
45020		EHI: Task releasing unreserved message
45021		EHI: message buffer release failed
45022		EHI: Unexpected message in mailbox
45023		EHI: Command parameter error
45024		EHI: Laser beam positioning not stable yet
45025		EHI: LV serial communications TX timeout
45026		EHI: timeout waiting for A/D output
45027		EHI: LV LCA not initialized
45028		EHI: LV LCA not done
45029		EHI: LV serial communications RX timeout
45030		EHI: LV board not connected
45031		EHI: incorrect light level at start of edge detection - check if plate loaded is too large
45032		EHI: Unable to balance stroke to better than head bpmaxerr percent
45033		EHI: library call failed
45034		EHI: the thermal head requires an upgrade
45035		EHI: case temperature high alarm, <Case temperature> C
45036		EHI: case temperature high warning, <Case temperature> C
45037		EHI: case temperature low alarm, <Case temperature> C
45038		EHI: case temperature low warning, <Case temperature> C
45039		EHI: ambient temperature high alarm, <Ambient temperature> C
45040		EHI: ambient temperature high warning, <Ambient temperature> C
45041		EHI: case and ambient temperature normal
45042		EHI: shutdown of thermal head due to temperature or humidity alarm
45043		EHI: thermal head humidity alarm, <Humidity> percent
45044		EHI: unable to learn focus, change focus mode or shift plot
45045		EHI: unable to find exposure power, set to 0 W
45100		STA: Internal: bad parameter
45101		STA: Statistic identifier <Statistic identifier> was not registered
45102		STA: Statistic identifier <Statistic identifier> has already been registered
45103		STA: System resource unavailable
45104		STA: Invalid statistic type for attempted operation
45105		STA: Statistic data type description index out of range
45204		PRD: WARNING: The device is currently running in simulation mode - for testing purposes only!
45205		PRD: Invalid limit tag specified
45206		PRD: Option '<Option name>' could not be enabled because option '<Option name>' is already enabled, only one is allowed
45207		PRD: Option '<Option name>' could not be enabled because it is not allowed in this configuration
45213		PRD: Chiller flow is too low
45232		PRD: Safety override switch is on, cannot plot with override on
45234		PRD: Warning: System Pressure Low
45235		PRD: Safety loop is not enabled (<I/OName>)
45236		PRD: Head Input Fault: <Input bit description> (<Input bit name>) In Unexpected State
45238		PRD: Temperature conversion failed
45242		PRD: Chiller flow is too low (<bit description>)
45244		PRD: The safety override keyswitch is activated
45245		PRD: Option '<Option name>' could not be enabled because option '<Option name>' needs to be enabled first.
45247		PRD: License is invalid, product family is '<License Product Family>', it is required to be '<Product Family>'
45248		PRD: License is invalid, option '<Option>' needs to be <Require state>
45249		PRD: The write laser power is not being detected
45250		PRD: License is invalid, unrecognized speed designator '<License Speed Designator>'
45251		PRD: Option '<Option>' has changed due to licensing, device must be reset
45263		PRD: Component not available to set offline or online
45265		PRD: Media dropped while drum spinning
45283		PRD: <Board name> (<Board ID>) <Relay name> relay contacts welded, replace board
45400		_405: PPC 405 General Failure
45401		_405: reset induced by software watchdog
45700		GMCEX: Bad Memory Address specified in monitor command
45701		GMCEX: GMCE board memory erase failure has occured
45702		GMCEX: Failure reading eeprom or flash memory
45703		GMCEX: Failure writing to eeprom or flash memory
45704		GMCEX: An Un-Supported CPU Interrupt has occured.
45705		GMCEX: RCON File Burn Status Query With Invalid File ID
45706		GMCEX: Invalid format type
45707		GMCEX: Invalid engineering units
45708		GMCEX: Failure creating or configuring TCP/IP socket
45709		GMCEX: Invalid IP address received for TH3 head
45710		GMCEX: A calculated file checksum is invlaid
46201		FWD: Empty firmware directory sector
46202		FWD: FWD Entry Not Found
46203		FWD: FWD handle is invalid
46204		FWD: FWD entry table integrity error
46205		FWD: Component ID is invalid
46206		FWD: Invalid function parameter
46207		FWD: Firmware directory entry table is full
46208		FWD: Invalid firmware directory entry or component check sum
46209		FWD: Directory table synchronization failure
46210		FWD: Directory table contains duplicated entries
46211		FWD: Directory table need to be validated
46212		FWD: End of directory table reached
46213		FWD: Firmware directory system is locked
46214		FWD: Failed to lock firmware directory system
46501		CFS: Invalid Path
46502		CFS: No More File/Dir Entry In Subdirectory
46503		CFS: API Function Not Supported
46504		CFS: File or Directory Already Exist
46505		CFS: File Or Directory Not Found
46506		CFS: Path Not Found
46507		CFS: Invalid File Attribute
46508		CFS: Invalid Handle
46509		CFS: Invalid Directory Tree
46510		CFS: File or Subdirectory Deletion Is Not Allowed
46511		CFS: No More Directory_Entry Is Available
46512		CFS: End Of File Reached
46513		CFS: File Write Is Not Allowed
46514		CFS: Media Is Full
46515		CFS: File Allocation Table Integrity Error
46516		CFS: Subdirectory Can Not Be Deleted
46517		CFS: Exclusive File Open Failure
46518		CFS: File/Dir Rename Failure
46519		CFS: Firmware Binary File Deletion Refused
46701		HIM: A parameter to an internal function is invalid
46702		HIM: Attempt to register too many notification callbacks
46703		HIM: Attempt to clear callback that was not previously established
46704		HIM: Head command currently in progress has been preempted
46705		HIM: The head programming operation could not be started
46706		HIM: Head programming state machine integrity violated
46707		HIM: File download state machine integrity violated
46708		HIM: No response from the head while downloading bootloader
46709		HIM: Protocol violation while downloading bootloader to the head
46710		HIM: Head does not support this version of bootloader
46711		HIM: No response from the head while programming
46712		HIM: Protocol violation while programming the head
46713		HIM: Head bootloader failed to program
46714		HIM: Serial port overflow while programming the head
46715		HIM: No data received from the workstation while programming the head
46716		HIM: 'S' expected (received <Received character>) at start of record <Line number> in S-record file
46717		HIM: Invalid record type found at record <Line number> in S-record file
46718		HIM: Invalid data byte <Invalid byte> found at offset <Record offset> of record <Line number> in S-record file
46719		HIM: Checksum failed on record <Line number> in S-record file
46720		HIM: Extra character(s) found at end of record <Line number> in S-record file
46721		HIM: Multiple head interface failures - check interface cable
46722		HIM: No head detected on fiber link - check cable and BOOTP server
46723		HIM: No head detected on serial link - check cable
46724		HIM: Thermal head FTP download file has an invalid checksum
46725		HIM: Thermal head FTP download file name is invalid
46801		CFL: Not connected to the Feature Licensing Server
46802		CFL: XML Parser Overflow
46803		CFL: XML Unknown escape sequence
46804		CFL: Illegal character in XML message
46806		CFL: Invalid State in XML parser
46807		CFL: Malformed XML message detected
46808		CFL: XML Parser memory allocation failure
46809		CFL: XML Parser does not support more than 8 bit characters
46810		CFL: Feature Licensing detected encryption memory corruption
46811		CFL: Feature Licensing detected a failure with a socket operation
46812		CFL: Communication timeout with the Feature Licensing Server
46813		CFL: XML Node Not found
46814		CFL: Feature licensing authentication failure
46815		CFL: Feature Licensing integrity check failed
46816		CFL: Licensing feature is not supported
46817		CFL: Feature value for "<Limit Name - This is the name of the feature value that is being verified>" (<Limit ID - The numeric representation (Limit Tag value>) is outside of it's licensed range
46818		CFL: Feature Licensing subsystem is not initialized
46819		CFL: Invalid limit tag <Tag - The parameter is the numeric value of the internally used limit tag> used.
46820		CFL: No more Feature Licensing connections available
46821		CFL: Invalid Feature Licensing connection ID
46822		CFL: Feature Licensing connection has been disconnected
46823		CFL: Feature Licensing connection failed
46824		CFL: Feature Licensing Server had an internal error
46825		CFL: Feature Licensing Server communication failed
46826		CFL: Feature Licensing Server cannot detect a service dongle
46827		CFL: Feature Licensing Server was requested information about a invalid service component
46828		CFL: Feature Licensing Server cannot find the appropriate license
46829		CFL: Feature Licensing Server cannot detect a customer dongle
46830		CFL: Invalid IP address used when communicating with the Feature Licensing Server
46831		CFL: Feature Licensing Server detects an invalid customer dongle
46832		CFL: Feature Licensing Server does not support this version of firmware
46833		CFL: Feature Licensing Server could not find requested feature
46834		CFL: Feature Licensing Server could not find requested tag
46835		CFL: Feature Licensing Server could not find requested value
46901		DCC: Just a placeholder error
47807		MDH: <motor name> stepper motor did not reach or remain on the sensor it was searching for [<I/O name>]
47904		MDH: Slip sheet bin is full, empty slip sheet bin