[00200] Section type is invalid
[00201] Section address is invalid
[00202] Directory does not exist
[00203] FCB checksum is invalid
[00204] File checksum is invalid
[00205] End of directory has been found
[00206] File not found
[00207] File is at EOF
[00208] The compressed file is corrupt
[00209] Unexpected software failure
[00400] Invalid function parameter
[00401] Invalid subsystem ID
[00402] Subsystem registration error
[00403] Invalid subsystem table
[00404] Duplicate error code found
[00405] Invalid error code
[00406] Error code was not found
[00407] The subsystem has not registered information
[00408] The search is complete
[00600] Boot level is invalid
[00601] Section type is invalid
[00602] Unexpected software failure
[00800] Flash type not recognized
[00801] Flash section invalid
[00802] Flash address invalid
[00803] Attempt to program failed
[00804] Attempt to erase failed
[00805] Attempt to program/erase timed out
[00806] The flash is in use by another task
[01000] Focus subsystem internal error
[01001] Invalid function parameter
[01002] Invalid command line argument
[01003] Failure opening a socket
[01004] Failure setting the socket options
[01005] Failure binding the socket
[01006] Failure listening to the socket
[01007] Failure accepting the socket
[01008] Failure sending the stream data
[01009] Failure receiving the stream data
[01010] End of stimulus data file reached
[01011] Stimulus table filled before download complete
[01012] Stimulus table is empty
[01013] LVDT primary offset out of range
[01014] LVDT primary amplitude out of range
[01015] LVDT primary phase out of range
[01016] LVDT secondary offset out of range
[01017] LVDT secondary amplitude out of range
[01018] Unsafe to execute command in the current state
[01019] The current focus mode is invalid
[01020] Timeout initializing focus lens tube
[01021] Excessive travel during focus lens tube init
[01022] Insufficient travel during focus lens tube init
[01023] Focus lens actuator offset current out of range
[01024] Focus drive system not initialized
[01025] Focus drive update timeout
[01026] Focus drive control signal out of range
[01027] LVDT sensor not calibrated
[01028] Timeout waiting to enter edge ISR state
[01029] Timeout waiting to learn focus
[01030] Focus Tracking Error
[01031] Timeout entering sine state in Bode analysis
[01032] Timeout entering park state in Bode analysis
[01033] Learn 2 not allowed twice in a row
[01034] Learn 1 must precede learn 2
[01035] Timeout waiting for fixed lens position
[01036] Timeout entring parked lens position
[01037] Total swaths exceeded: holding for remainder of image
[01038] LVDT primary gain out of range
[01039] Focus drive is over current
[01200] Unexpected software failure
[01201] FPGA programing: 'Init pin' asserted before config load done
[01202] FPGA programing: 'Done pin' not asserted after config loaded
[01203] FPGA programing: Timeout on 'Init pin deassert after 'Prg pin' deassert
[01204] FPGA programing: Timeout on 'Init init' assert after 'Pgm pin assert
[01205] FPGA programing: Timeout on PLL lock status after reset
[01206] SAT: Timeout on satellite register update
[01207] Invalid command line argument
[01208] Satellite not detected during system initialization
[01209] Polled read satellite interface read timeout
[01210] Polled read satellite interface received framing error
[01211] Polled read satellite interface received parity error
[01400] The JTAG device is invalid
[01401] The file version is invalid
[01402] The BSDL configuration is invalid
[01403] Failure verifying the BSDL data
[01404] Failure reading the program file
[01405] Unexpected software failure
[01600] Invalid function parameter
[01601] Invalid subsystem ID
[01602] Subsystem registration error
[01603] Invalid subsystem table
[01604] Invalid format string
[01605] Timeout entering the command line
[01606] Maximum command line length exceeded
[01607] Command not found
[01608] Monitor command access level insufficient
[01609] Command has too many tokens
[01610] Command characters are not available
[01611] Command has no tokens
[01612] Timeout receiving characters
[01613] Confirmation has been denied
[01614] The confirmation character is invalid
[01615] Timeout entering the confirmation
[01616] The password is invalid
[01617] Timeout entering the password
[01618] The subsystem has not registered commands
[01619] The subsystem has not registered information
[01620] Command line parameter range error
[01621] Unexpected software failure
[01800] The string queue is empty
[01801] The string queue is full
[01802] The packet queue is empty
[01803] The packet queue is full
[01804] The packet length is invalid
[01805] The packet offset is invalid
[02000] Invalid function parameter
[02001] Invalid subsystem ID
[02002] Subsystem registration error
[02003] Invalid subsystem table
[02004] Duplicate parameter key found
[02005] Invalid parameter key
[02006] The buffer size is invalid
[02007] The parameter has not been found
[02008] Parameter access level insufficient
[02009] The parameter copy is invalid
[02010] The parameter element is invalid
[02011] The source / destination copy is invalid
[02012] The parameter syntax is invalid
[02013] The parameter range is invalid
[02014] The string parameter syntax is not supported
[02015] The string parameter length is invalid
[02016] The subsystem has not registered parameters
[02017] The subsystem has not registered information
[02018] The parameter division is invalid
[02019] Unexpected software failure
[02200] The registry is in use by another task
[02201] The registry is full, execute "Reg Optimize"
[02202] The search of the registry is complete
[02203] RCB checksum is invalid
[02204] Entry checksum is invalid
[02205] Entry size is invalid
[02206] A registry key was not found
[02207] A registry key already exists
[02208] The directory section is not erased
[02209] The directory sections are different
[02210] Both directory sections are corrupt
[02211] The primary directory section was recovered
[02212] The primary directory section is corrupt
[02213] The secondary directory section was recovered
[02214] The secondary directory section is corrupt
[02215] The baseline directory section is corrupt
[02216] The registry is invalid
[02400] A function parameter is invalid
[02401] The event flag(s) are not present
[02402] The partition pool is empty
[02403] The partition pool is full
[02404] The queue is empty
[02405] The queue is full
[02406] Timeout obtaining the semaphore
[02407] Unexpected software failure
[02600] Checksum invalid loading the firmware bundle
[02601] Section type is invalid
[03000] The serial port handle is invalid
[03001] The serial port state is invalid
[03002] The serial port notification is invalid
[03003] The serial port buffer is empty
[03004] The serial port buffer is full
[03005] Unexpected software failure
[03400] Verbose initialization failed
[03401] Invalid subsystem ID
[03402] Invalid verbose level
[03403] Unexpected software failure
[03600] Invalid function parameter
[03601] Invalid subsystem ID
[03602] Subsystem registration error
[03603] Invalid subsystem information
[03604] Invalid subsystem acronym
[03605] Invalid sorting option
[03800] The health subsystem has been shutdown
[03801] All metric faults have been cleared
[03802] The satellite is invalid
[03803] The command syntax is invalid
[03804] The mask state is invalid
[03805] The metric point is invalid
[03806] Unexpected software failure
[03810] Volt Range Error [mask 0]: HC Board (3.3V)
[03811] Volt Range Error [mask 1]: HC Board (1.8V)
[03812] Volt Range Error [mask 2]: HC Board (2.5V)
[03813] Volt Range Error [mask 3]: HC Board (2.5Vref)
[03814] Volt Range Error [mask 4]: HC Board (1.2V)
[03815] Volt Range Error [mask 5]: HC Board (1.25Vref)
[03816] Volt Range Error [mask 6]: HC Board (0.9Vref)
[03817] Volt Range Error [mask 7]: HC Board (VDDR)
[03818] Volt Range Error [mask 133]: HC Board (VDD8)
[03819] Volt Range Error [mask 9]: HC Board (GND)
[03820] Volt Range Error [mask 134]: HC Board (VSS12)
[03821] Volt Range Error [mask 11]: HC Board (IBV)
[03822] Volt Range Error [mask 12]: HC Board (VDD_FAD)
[03823] Volt Range Error [mask 13]: ACT Board (3.3V)
[03824] Volt Range Error [mask 14]: ACT Board (2.5V)
[03825] Volt Range Error [mask 15]: ACT Board (VDD12)
[03826] Volt Range Error [mask 16]: ACT Board (VDDR)
[03827] Volt Range Error [mask 17]: ACT Board (VSS12)
[03828] Volt Range Error [mask 18]: ACT Board (VSSR)
[03829] Volt Range Error [mask 19]: ACT Board (SHUT2Volt)
[03830] Volt Range Error [mask 20]: ACT Board (VBUS)
[03831] Volt Range Error [mask 135]: HC Board (VSS8)
[03832] Volt Range Error [mask 136]: HC Board (SHUT2Volt)
[03833] Temp Range Error [mask 23]: ACT Board (BoardTemp)
[03834] Volt Range Error [mask 137]: HC Board (VBUS_TR)
[03835] Volt Range Error [mask 25]: ACT Board (1.25Vref)
[03836] Pres Range Error [mask 26]: ACT Board (AirPress)
[03837] Volt Range Error [mask 140]: HC Board (VBUS_FAD)
[03838] Temp Range Error [mask 28]: NPE Board (BoardTmp)
[03839] Curr Range Error [mask 145]: WLC Board (OCTrip)
[03840] Volt Range Error [mask 146]: HC Board (VPPCTRL)
[03841] Temp Range Error [mask 31]: RFE Board (BoardTmp)
[03842] Humi Range Error [mask 32]: IBS Board (Humidity)
[03843] Volt Range Error [mask 33]: WLC Board (3.3V)
[03844] Volt Range Error [mask 34]: WLC Board (2.5V)
[03845] Volt Range Error [mask 35]: WLC Board (VDD12)
[03847] Volt Range Error [mask 37]: WLC Board (VSS12)
[03848] Temp Range Error [mask 38]: WLC Board (BoardTmp)
[03849] Volt Range Error [mask 39]: WLC Board (VBUS)
[03850] Curr Range Error [mask 40]: WLC Board (IDOCTRIP)
[03852] Volt Range Error [mask 42]: WLC Board (GND)
[03854] Temp Range Error [mask 44]: WLC Board (Laser 1)
[03855] Temp Range Error [mask 45]: WLC Board (Laser 2)
[03856] Temp Range Error [mask 46]: LVDL Board (PulseAmp)
[03857] Temp Range Error [mask 47]: LVDL Board (StrokeAmp)
[03858] Temp Range Error [mask 48]: LVDL Board (VPP3Reg)
[03859] Volt Range Error [mask 49]: LVDL Board (VPP1-80)
[03860] Volt Range Error [mask 50]: LVDL Board (VPP2-40)
[03861] Volt Range Error [mask 51]: LVDL Board (A+5V)
[03862] Volt Range Error [mask 52]: LVDL Board (A-5V)
[03863] Volt Range Error [mask 53]: LVDL Board (+2.5V)
[03864] Volt Range Error [mask 54]: LVDL Board (+1.8V)
[03865] Volt Range Error [mask 55]: LVDL Board (VPP3-25)
[03866] Temp Range Error [mask 56]: PDB Board (Module A)
[03867] Temp Range Error [mask 57]: PDB Board (Module B)
[03868] Temp Range Error [mask 58]: PDB Board (Module C)
[03869] Temp Range Error [mask 59]: PDB Board (Module D)
[03870] Temp Range Error [mask 60]: PDB Board (Module E)
[03871] Temp Range Error [mask 61]: PDB Board (Module F)
[03872] Temp Range Error [mask 62]: PDB Board (Module G)
[03873] Temp Range Error [mask 63]: PDB Board (Module H)
[03874] Volt Range Error [mask 64]: LVDU Board (+2.5V)
[03875] Volt Range Error [mask 65]: LVDU Board (+1.8V)
[03876] Volt Range Error [mask 66]: LVDU Board (VPP3-25)
[03877] Volt Range Error [mask 67]: LVDU Board (3.3V)
[03878] Volt Range Error [mask 109]: HC Board (1.25Vref)
[03879] Temp Range Error [mask 110]: HC Board (Laser 1)
[03880] Temp Range Error [mask 111]: HC Board (Laser 2)
[03881] Volt Range Error [mask 126]: HC Board (5VA)
[03882] Temp Range Error [mask 127]: HC Board (FPGATemp)
[03883] Temp Range Error [mask 128]: HC Board (FocusTemp)
[03884] Temp Range Error [mask 129]: HC Board (BoardTemp)
[03885] Curr Range Error [mask 130]: HC Board (VBUSCur)
[03886] Volt Range Error [mask 131]: HC Board (ACT2.5V)
[03887] Volt Range Error [mask 132]: HC Board (VDD12)
[03888] Humi Range Error [mask 88]: PBP2 Board (Humidity)
[03889] Volt Range Error [mask 89]: PBP2 Board (3.3V)
[03890] Curr Range Error [mask 90/91/92/93/94]: Backplane (48VCur)
[03891] Temp Range Error [mask 91/99]: LVD1 Board (BoardTmp)
[03892] Temp Range Error [mask 92/100]: LVD2 Board (BoardTmp)
[03893] Temp Range Error [mask 93/101]: LVD3 Board (BoardTmp)
[03893] Volt Range Error [mask 95]: Backplane (WLC 48V)
[03894] Temp Range Error [mask 94/102]: LVD4 Board (BoardTmp)
[03894] Volt Range Error [mask 96]: Backplane (PDB 48V)
[03895] Volt Range Error [mask 97]: Backplane (3.3V)
[03900] NPE board interface timeout
[03901] ACT board interface timeout
[03902] PBP board interface timeout
[03903] IBS board interface timeout
[03904] DBP board interface timeout
[03905] WLC board interface timeout
[03906] RFE board interface timeout
[03907] LVDU board interface timeout
[03908] LVDL board interface timeout
[03909] NPE board interface framing error
[03910] ACT board interface framing error
[03911] PBP board interface framing error
[03912] IBS board interface framing error
[03913] DBP board interface framing error
[03914] WLC board interface framing error
[03915] RFE board interface framing error
[03916] LVDU board interface framing error
[03917] LVDL board interface framing error
[03918] NPE board interface parity error
[03919] ACT board interface parity error
[03920] PBP board interface parity error
[03921] IBS board interface parity error
[03922] DBP board interface parity error
[03923] WLC board interface parity error
[03924] RFE board interface parity error
[03925] LVDU board interface parity error
[03926] LVDL board interface parity error
[03927] NPE board interface fifo overflow
[03928] ACT board interface fifo overflow
[03929] PBP board interface fifo overflow
[03930] IBS board interface fifo overflow
[03931] DBP board interface fifo overflow
[03932] WLC board interface fifo overflow
[03933] RFE board interface fifo overflow
[03934] LVDU board interface fifo overflow
[03935] LVDL board interface fifo overflow
[03936] Satellite missed interrupt
[03937] PBP2 board interface timeout
[03938] PBP2 board interface fifo overflow
[03939] LVDP board interface timeout
[03940] LVDN board interface timeout
[03941] LVDP board interface framing error
[03942] LVDN board interface framing error
[03943] LVDP board interface parity error
[03944] LVDN board interface parity error
[03945] LVDP board interface fifo overflow
[03946] LVDN board interface fifo overflow
[04000] Unexpected software failure
[04001] Invalid command line argument
[04002] No existing servo handler
[04003] Hardware / firmware interrupt counts differ
[04004] Satellite timer stopped
[04005] Satellite not installed
[04006] Satellite board is wrong type
[04007] Satellite version not supported
[04008] Satellite configuration incorrect
[04009] Satellite version reads inconsistent
[04010] All status faults have been cleared
[04011] RFE power relay frozen 'on'
[04012] RFE power relay frozen 'off'
[04013] RFE power relay may be frozen 'on'
[04014] RFE power relay may be frozen 'off'
[04015] Use command that specifies board number
[04016] Satellite version incorrect
[04017] Could not set Satellite ID register
[04020] NPE: IO disabled
[04021] NPE: parity error
[04022] NPE: framing error
[04023] NPE: VDD undervoltage
[04024] NPE: VSS undervoltage
[04025] NPE: pcb temp no ack
[04026] NPE: power monitor fault
[04027] ACT: IO disabled
[04028] ACT: parity error
[04029] ACT: framing error
[04030] ACT: dac fifo overflow
[04033] ACT: power supply fault
[04034] ACT: shutter2 fault
[04035] PBP: IO disabled
[04036] PBP: parity error
[04037] PBP: framing error
[04038] PBP: VDD undervoltage
[04039] PBP: VSS undervoltage
[04041] IBS: IO disabled
[04042] IBS: parity error
[04043] IBS: framing error
[04044] IBS: VDD undervoltage
[04045] IBS: VSS undervoltage
[04046] DBP: IO disabled
[04047] DBP: parity error
[04048] DBP: framing error
[04049] DBP: VDD undervoltage
[04050] DBP: VSS undervoltage
[04051] DBP: power monitor fault
[04052] WLC: IO disabled
[04053] WLC: parity error
[04054] WLC: framing error
[04055] WLC: laser1 over current
[04056] WLC: laser2 over current
[04057] RFE: IO disabled
[04058] RFE: power monitor fault
[04059] RFE: parity error
[04060] RFE: framing error
[04061] RFE: VDD undervoltage
[04062] RFE: VSS undervoltage
[04063] RFE: PCB temp no ACK fault
[04064] RFE: LD flex not detected
[04065] RFE: PSD flex not detected
[04066] LVDU: IO disabled
[04067] LVDU: parity error
[04068] LVDU: framing error
[04070] LVDU: power supply fault
[04071] LVDU: datapath CRC error
[04072] LVDL: IO disabled
[04073] LVDL: parity error
[04074] LVDL: framing error
[04076] LVDL: power supply fault
[04077] LVDL: datapath CRC error
[04078] PBP2: power supply fault
[04079] PBP2: input voltage fault
[04080] PBP2: unexpected reset
[04081] LVD: DVS Timeout on Board 0
[04082] LVD: DVS Timeout on Board 1
[04083] LVD: DVS Timeout on Board 2
[04084] LVD: DVS Timeout on Board 3
[04085] LVD: DVS Timeout on Board 4
[04086] LVD: DVS Timeout on Board 5
[04087] LVD: DVS Timeout on Board 6
[04088] LVD: DVS Timeout on Board 7
[04089] LVD: parity error on Board 0
[04090] LVD: parity error on Board 1
[04091] LVD: parity error on Board 2
[04092] LVD: parity error on Board 3
[04093] LVD: parity error on Board 4
[04094] LVD: parity error on Board 5
[04095] LVD: parity error on Board 6
[04096] LVD: parity error on Board 7
[04100] NPE: Retrying the satellite configuration
[04101] ACT: Retrying the satellite configuration
[04102] PBP: Retrying the satellite configuration
[04103] IBS: Retrying the satellite configuration
[04104] DBP: Retrying the satellite configuration
[04105] WLC: Retrying the satellite configuration
[04106] RFE: Retrying the satellite configuration
[04107] LVDU: Retrying the satellite configuration
[04108] LVDL: Retrying the satellite configuration
[04109] PBP2: Retrying the satellite configuration
[04110] LVDP: Retrying the satellite configuration
[04111] LVDN: Retrying the satellite configuration
[04150] LVD: framing error on Board 0
[04151] LVD: framing error on Board 1
[04152] LVD: framing error on Board 2
[04153] LVD: framing error on Board 3
[04154] LVD: framing error on Board 4
[04155] LVD: framing error on Board 5
[04156] LVD: framing error on Board 6
[04157] LVD: framing error on Board 7
[04158] HC: laser1 over current
[04159] HC: laser2 over current
[04160] HC: shutter2 fault
[04200] Network initialization failed
[04201] Failure initializing the Turbo Treck TCP/IP stack
[04202] The network address is invalid
[04203] The network interface is invalid
[04204] Failure initializing the network interface
[04205] The network interface loopback test is invalid
[04206] Failure retrieving diagnostics from the network interface
[04207] The telnet session handle is invalid
[04208] The telnet session state is invalid
[04209] The telnet session notification is invalid
[04210] The telnet session buffer is empty
[04211] The telnet session buffer is full
[04212] Failure opening a socket
[04213] Failure sending the BOOTP request
[04214] The file does not support reads
[04215] The file does not support writes
[04216] The file is unknown
[04217] The autoboot algorithm prevents erasing the file
[04218] The flags are invalid
[04219] The buffer is invalid
[04220] The network interface loopback test has failed
[04221] Unexpected software failure
[04400] The BPD is in use by another task
[04401] Beam-pointing initialization failed
[04402] The control mode is invalid
[04403] The laser mode is invalid
[04404] The sensor mode is invalid
[04405] The DBPS configuration is invalid
[04406] The DBPS configuration is unknown
[04407] Timeout waiting for the sample acquisition
[04408] The beam-pointing controller is invalid
[04409] The beam-pointing actuator is invalid
[04410] Invalid function parameter
[04411] The sample data is preventing a linear fit
[04412] The calibrated values are out-of-range
[04413] The beam-pointing signal level is invalid
[04414] The beam-pointing actuator is saturated
[04415] The beam-pointing controller is unstable
[04416] The configuration is not supported
[04417] Unexpected software failure
[04600] The data logger is in use by another task
[04601] Data logger initialization failed
[04602] The control mode is invalid
[04603] The sample configuration is invalid
[04604] Invalid function parameter
[04605] The sample point is invalid
[04606] Point registration error
[04607] Invalid field table
[04608] The sample state is invalid
[04609] The trigger event is invalid
[04610] The trigger delay is invalid
[04611] Unexpected software failure
[04800] The diagnostic stream is in use by another task
[04801] Failure opening a socket
[04802] Failure setting the socket options
[04803] Failure binding the socket
[04804] Failure listening to the socket
[04805] Failure accepting the socket
[04806] Failure sending the stream data
[04807] Unexpected software failure
[05000] The event logger is in use by another task
[05001] Event logger initialization failed
[05002] The event point is invalid
[05003] The cache state is invalid
[05004] Invalid function parameter
[05005] Unexpected software failure
[05200] The LDD is in use by another task
[05201] Laser diode initialization failed
[05202] The control mode is invalid
[05203] The laser mode is invalid
[05204] The command setpoint is invalid
[05205] The drive mode is invalid
[05206] The laser diode is invalid
[05207] The control mode transition is invalid
[05208] Failure controlling the WLC
[05209] Timeout waiting for the sample acquisition
[05210] The calibrated values are out-of-range
[05211] Timeout waiting for the write laser to be detected
[05212] Timeout waiting for the laser current to be ramped
[05213] The beam-pointing mode is invalid
[05214] The light valve mode is invalid
[05215] The laser power signal level is invalid
[05216] The laser current exceeds the current limits
[05217] The laser power is unstable
[05218] The write laser has been disabled
[05219] The write laser is over-temperature
[05220] Unexpected software failure
[05400] Insufficient cycles for Bode analysis
[05401] The step response is invalid
[05402] The step response has failed
[05403] Unexpected software failure
[05600] The system is in use by another task
[05601] The firmware upgrade is complete
[05602] The firmware upgrade has failed
[05603] The functionality is not supported
[05604] The command sequence is invalid
[05605] The head / plot command is invalid
[05606] The head / plot command is not supported
[05607] The control mode is invalid
[05608] The shutter type / control is invalid
[05609] Failure opening / closing the internal shutter
[05610] Failure determining the edge detect information
[05611] The edge detect state is invalid ( on / off plate )
[05612] Failure resetting the edge detect
[05613] The media is not supported
[05614] Failure accessing the media
[05615] The series / system / NVS parameter is invalid
[05616] The series / system / NVS parameter length is invalid
[05617] Failure creating the system parameter
[05618] Failure reading the system parameter
[05619] The system parameter syntax is invalid
[05620] Failure verifying the system parameters
[05621] System parameter(s) have been disabled
[05622] Failure configuring the focus driver
[05623] Failure configuring the plot subsystem
[05624] Failure determining the head position
[05625] Failure of the focus learn
[05626] Failure accessing the beam-balance sensor
[05627] Failure accessing the focus driver
[05628] Failure accessing the laser diode driver
[05629] Failure accessing the light valve driver
[05630] Failure accessing the media subsystem
[05631] Failure accessing the plot subsystem
[05632] The write laser control mode is in progress
[05633] The stroke calibration is in progress
[05634] The focus control mode is in progress
[05635] Timeout waiting for the write laser
[05636] Timeout waiting for the stroke calibration
[05637] Timeout waiting for the focus learn
[05638] The write laser control mode has been aborted
[05639] The stroke calibration has been aborted
[05640] The focus control mode has been aborted
[05641] Failure determining the head information
[05642] Warning fault(s) have been discarded
[05643] Fatal fault(s) have been discarded
[05644] A warning fault has been generated for testing
[05645] A shutdown fault has been generated for testing
[05646] A fatal fault has been generated for testing
[05647] The command syntax is invalid
[05648] The stroke clock frequency is too high ( > 1520 kHz )
[05649] The beam-balance has failed
[05650] Health metric(s) have faulted
[05651] Health metric(s) have been masked
[05652] Satellite fault(s) have been detected
[05653] Satellite fault(s) have been masked
[05654] The exposure head has been disabled
[05655] The host has specified an invalid plot setup
[05656] The light valve annealing is in progress
[05657] The light valve annealing is not required
[05658] The write laser standby is in progress
[05659] The write laser standby is not required
[05660] Failure accessing the beam-pointing driver
[05661] The laser diode control mode is invalid
[05662] The rated power has been exceeded
[05663] Unexpected software failure
[05664] The firmware downgrade is complete
[05667] The command sequence is invalid. Write laser in use.
[05668] The command sequence is invalid. Focus in use.
[05669] The command sequence is invalid. Write laser and Focus in use.
[05800] The LVD is in use by another task
[05801] Light valve initialization failed
[05802] The hardware version(s) are invalid
[05803] Insufficient configuration access level
[05804] The stroke offset and / or width is invalid
[05805] The control mode is invalid
[05806] The polarity type is invalid
[05807] The spot index is invalid
[05808] The spot state is invalid
[05809] The polarity state is invalid
[05810] The spot level is invalid
[05811] The pattern string has invalid characters
[05812] The length of the pattern string is invalid
[05813] The diagnostic command is invalid
[05814] The diagnostic function is not supported
[05815] The diagnostic function has failed
[05816] Unexpected software failure
[06000] The media is in use by another task
[06001] The media index is invalid
[06002] Failure writing the media key
[06003] Failure reading the media key
[06004] The media key is invalid
[06005] The media is not supported
[06006] Unexpected software failure
[06200] The plot is in use by another task
[06201] Plot initialization failed
[06202] The control mode is invalid
[06203] The image configuration is invalid
[06204] The synthesizer configuration is invalid
[06205] The TPG configuration is invalid
[06206] The TPG label is invalid
[06207] The pattern data is invalid
[06208] The combination data is invalid
[06209] Invalid function parameter
[06210] The command packet is invalid
[06211] The protocol version is unsupported
[06212] The sequence number is invalid
[06213] Failure opening a socket
[06214] Failure binding the socket
[06215] Failure receiving from the socket
[06216] Failure sending to the socket
[06217] Failure getting the ARP entry
[06218] A partial swath is still buffered, the image may be corrupt
[06219] The plot has been aborted due to multiple hosts
[06220] The plot has been aborted prematurely
[06221] The mainscan image size is mismatched, the image may be corrupt
[06222] FIFO underrun error, the image may be corrupt
[06223] FIFO overflow error, the image may be corrupt
[06224] SCLK overrun error, the image may be corrupt
[06225] Swath buffer overflow error, the image may be corrupt
[06226] The TPG pattern has not been found
[06227] Unexpected software failure
[06228] The plot has been aborted because the datapath isn't ready
[06400] The BBS is in use by another task
[06401] Beam-balance initialization failed
[06402] Failure opening the media
[06403] Failure closing the media
[06404] The mode / state of the laser diode is invalid
[06405] The mode / state of the beam-pointing is invalid
[06406] The mode of the light valve is invalid
[06407] The control mode is invalid
[06408] The head power mode is invalid
[06409] The shutter control is invalid
[06410] The spot increment is invalid
[06411] The specified spots could not be configured
[06412] The polarity could not be configured
[06413] A beam-balance is in progress
[06414] The beam-balance has been aborted
[06415] Beam-balance prevented by the range of pulse heights
[06416] Beam-balance prevented by drift errors
[06417] Beam-balance error exceeds the maximum error
[06418] Insufficient signal for the beam-balance
[06419] The beam-balance sensor samples are saturated
[06420] Timeout waiting for the sample acquisition
[06421] The polarity state is invalid
[06422] The beam piston is invalid
[06424] Imaging may be affected by a dead pixel
[06425] Unexpected software failure
[06600] The trace mode is invalid
[06601] The trace buffer is invalid
[06602] The memory test buffer specification is invalid
[06603] The memory test failed
[06604] The Ethernet controller data bit walk test failed
[06605] The address bus bit walk test failed
[06606] The relative clock frequency test failed
[06800] The logic analyzer is in use by another task
[06801] The logic analyzer is invalid
[06802] The control mode is invalid
[06803] The trigger configuration is invalid
[06804] The hardware configuration is not supported
[06805] Unexpected software failure
[07000] The DTL is in use by another task
[07001] The datalink port state is invalid
[07002] The logical channel is invalid
[07003] The datalink has lost synchronization
[07004] The datalink port is not idle
[07005] The datalink has been corrupted
[07006] Failure opening a socket
[07007] Failure setting the socket options
[07008] Failure binding the socket
[07009] Failure listening to the socket
[07010] Failure accepting the socket
[07011] Failure receiving the character(s)
[07012] Failure sending the character(s)
[07013] Unexpected software failure
[07400] The shutter control is invalid
[07401] The control mode is invalid
[07402] The command packet is invalid
[07403] The command packet length is invalid
[07404] The command code is not supported
[07405] The command parameter is invalid
[07406] Timeout waiting for the write laser
[07407] Timeout waiting for the focus
[07408] Timeout waiting for the stroke calibration
[07409] The NVS parameter is not supported
[07410] Failure reading the NVS parameter
[07411] Failure writing the NVS parameter
[07412] Failure constructing the media specifier
[07413] Failure translating the error information
[07414] The error information is invalid
[07415] The requested baud rate is not supported
[07416] The requested baud rate is too low
[07417] The unsolicited packet has been blocked
[07418] The requested application protocol is not supported
[07419] Unexpected software failure
[07600] The IBS is in use by another task
[07601] Internal balance initialization failed
[07602] The internal beam-balance sensor calibration is invalid
[07603] Failure opening the media
[07604] Failure closing the media
[07605] The mode / state of the laser diode is invalid
[07606] The mode / state of the beam-pointing is invalid
[07607] The mode of the light valve is invalid
[07608] The control mode is invalid
[07609] The spot increment is invalid
[07610] The specified spots could not be configured
[07611] The polarity could not be configured
[07612] Failure configuring the internal beam-balance sensor
[07613] Failure calibrating the internal beam-balance sensor
[07614] An internal balance is in progress
[07615] The internal balance has been aborted
[07616] Internal balance prevented by the range of pulse heights
[07617] Internal balance prevented by drift errors
[07618] Internal balance error exceeds the maximum error
[07619] Insufficient signal at maximum gain
[07620] The internal beam-balance sensor samples are saturated
[07621] Timeout waiting for the sample acquisition
[07622] The board version does not support the functionality
[07623] Unexpected software failure
[07800] The registry is in use by another task
[07801] A registry key was not found
[07802] A registry key already exists
[07803] Entry size is invalid
[07804] Unexpected software failure
[08000] The ACT is in use by another task
[08001] Actuator initialization failed
[08002] The board version is not supported
[08003] The shutter control is invalid
[08004] The stepper driver is invalid
[08005] The number of steps is invalid
[08006] The shutter state is unknown
[08007] The stepper driver is active
[08008] Timeout actuating the stepper driver
[08009] The fast shutter was not open for imaging
[08010] Unexpected software failure
[08200] The cache is in use by another task
[08201] Cache initialization failed
[08202] The search of the cache is complete
[08203] CCB checksum is invalid
[08204] Entry checksum is invalid
[08205] Entry length is invalid
[08206] The direction is invalid
[08207] The cache is invalid
[08208] Invalid function parameter
[08209] Unexpected software failure