| 15002:autoloader operation timed out |
15050:in reset condition |
| 15051:ALE board not installed |
15052:autoloader operation timed out |
| 15053:Autoloader operation aborted |
15054:invalid ALE state |
| 15055:software error!! |
15056:Invalid media number in plate location %d |
| 15057:command already in progress |
15058:Plate size is out of range |
| 15059:Autoloader is not initialized, possibly due to an opened door |
15060:Position the %u mm tall plate into the leading edge clamp |
| 15061:Unload complete, please remove the plate from unload ramp |
15062:plate loaded incorrectly, remove plate from drum |
| 15063:LUE board incorrect version for recorder software |
15064:Leading edge clamp cylinder error, both sensors activated |
| 15065:Trailing edge clamp actuator bar cylinder error, both sensors activated |
15066:Drum roller cylinder error, both sensors activated |
| 15067:Trailing edge clamp lock/unlock cylinder error, both sensors activated |
15068:move clamps to park position, then select RESUME |
| 15069:load command in progress |
15070:unload command in progress |
| 15071:remove plate from drum |
15072:remove plate partially on drum |
| 15073:trailing edge clamp status conflict, setting te state flag to<0|1>. ( "1" indicates "on drum", "0" indicates "on tec backbone" ) |
15074:trailing edge clamps failed to unlock |
| 15075:trailing edge clamps failed to lock |
15076:trailing edge clamps not on actuator |
| 15077:trailing edge clamps already on actuator, possible sensor or software error. |
15078:no plate on drum |
| 15079:timeout moving leading edge cylinder |
15080:timeout moving trailing edge cylinder |
| 15081:timeout moving load ramp cylinder |
15082:timeout moving roller cylinder |
| 15083:remove plate detected on unload ramp |
15084:recorder exit flap not opening(/closing) |
| 15085:roller on drum |
15086:leading-edge actuator on drum |
| 15087:trailing-edge actuator on drum |
15088:remove plate from load ramp (wrong size) |
| 15150:picker command timed out |
15151:stepper drivers not initialized |
| 15152:picker busy |
15153:Autoloader Axis operation aborted |
| 15154:Y-axis travel limit detected |
15155:home switch unexpectedly activated |
| 15156:away switch unexpectedly activated |
15157:<axis number> axis stuck home. Timeout occured leaving home position |
| 15158:stuck away |
15159:couldn't open cassette lid in bay <bay number> |
| 15160:cassette bay <bay#> in use |
15161:cassette bay <bay#> open |
| 15162:timeout moving bay <bay#> shutter cylinder |
15163:Plate size in bay <bay#> is zero. Load bay to set size. |
| 15164:current fault, shutting down CB rollers |
15165:bay <bay#> still loading, please open and close this bay |
| 15166:bay <bay#> location not initialized in NVS |
15167:new bay number out of range |
| 15170:remove plate from picker |
15171:remove plate from unload table |
| 15172:plate lost after picking, check inside recorder |
15173:timeout moving unload cylinder |
| 15174:timeout moving table tilt cylinder |
15175:timeout moving table stow cylinder |
| 15176:no plate detected on unload vacuum cups |
15177:picker vacuum below threshold |
| 15178:no plate on picker |
15179:no plate on unload table |
| 15180:remove plate from picker (plate smaller than expected) |
15181:remove plate from picker (plate too large or slip sheet attached) |
| 15182:plate on picker, remove plate from unload ramp |
15183:remove plate not fully on unload table |
| 15184:plate not on picker, disabling vacuum |
15185:plate not on unload table, disabling vacuum |
| 15186:picker too low, can't tilt table |
15187:Picker vacuum threshold too low or sensing error |
| 15189:plate not found during initial seek |
15190:remove plate from picker (slip sheet attached or plate too large |
| 15191:Picker could not locate the bay detect tab in cassette bay %d |
15192:End of bay <bay#> detection tab not found, picker may be stuck. |
| 15193:Aluminum plate sensor disabled, ensure no cardboard in cassette! |
15194:plate picker vacuum did not release in time, check air lines |
| 15195:Unload table vacuum did not release in time, check air lines |
15196:Picker vacuum sensed plate before vacuum turned on, remove platefrom picker \ncheck Picker Vacuum Threshold |
| 15197:Unload vacuum sensed plate before vacuum turned on, check Unload Vacuum Threshold |
15198:Attempted to move PZ below limit while over engine, check that platesize is not smaller than minimum. |
| 15200:Invalid processor number in media number <#> |
15201:Invalid processor interface code in media number <#> |
| 15202:continuing to send the previous plate to the processor |
15203:waiting for the previous plate to clear the conveyor |
| 15204:remove plate from conveyor or check sensor |
15205:no conveyor bridge or output cassette detected |
| 15206:timeout waiting for plate to enter processor #%d |
15207:processor #%d busy |
| 15208:processor #%d not ready |
15209:LUE power 24V low, possible conveyer motor over current fault. |
| 15210:plate didn't arrive in conveyor |
15211:plate conveyor lid open |
| 15212:processor #%d fault detected! Clear fault before continuing. |
15213:error occured on previous plate, check if processor is ready. |
| 15214:check for plate stuck in conveyor or processor #%d interface error |
15215:conveyor roller motor overcurrent detected |
| 15216:conveyor belt motor overcurrent detected |
15220:pick command in progress |
| 15221:process command in progress |
15222:remove plate from load ramp (wrong size) |
| 15223:picker stuck in cassette bay %d |
15224:picker microswitch activated before plate seek, check switch,cable and plate_jog_y |
| 15225:intermittent picker microswitch detected, cable and switch should be checked. |
15226:Has plate been removed from picker ?Yes,Resume - No,Clear |
| 15227:Has plate been removed from Unload table ?Yes,Resume - No,Clear |
15228:Has plate been removed from Drum ?'Resume'= Yes -*- 'Clear' = No |
| 15250:timeout waiting for load button to be pressed |
15251:plate not detected on load ramp |
| 15252:plate larger than expected |
15253:plate smaller than expected |
| 15254:remove plate detected on load ramp |
15255:timeout waiting for plate removal from load ramp |
| 15256:image cancelled by workstation during load |
15257:Software error: invalid lamp state %d selected in set_lamp_state() |
| 15258:Software error: invalid image task state %d selected in update_lamps() |
15259:load ramp is tilted into drum no-fly zone |
| 15260:Plate width under 559mm, load onto rightmost and middle pins |
15281:Please load plate |
| 15282:Please load carrier |
15283:Please unload plate |
| 15284:Please unload carrier |
15285:Plate smaller than expected. Device is unable to unload this plate safely. Pleaseremove plate from drum. |
| 15286:Plate larger than expected. To try another plate, press Resume. |
15287:Plate smaller than expected. To try another plate, press Resume. |
| 15300:Separator timed out moving out |
15301:Picker timed out moving |
| 15302:Separator obstructed by picker |
15303:Picker obstructed by separator|picker in |
| 15304:Unload Table timed out moving up|down |
15305:Unload cups rotated, can't move unload carriage |
| 15306:Unload carriage not in safe position to rotate cups |
15307:Load ramp timed out moving out |
| 15308:Unload Cups timed out moving in |
15309:Rotator move timed out moving to rotated|unrotated position |
| 15310:AL SW error: invalid parameter file <filename> line <line number> |
15311:Plate still on unload table, can't unload |
| 15312:Please remove plate from unload table |
15313:Please close plate cover |
| 15314:Please put plate cover in manual bypass position |
15315:Traveller rotate position sensor is already high (sensor may be broken) |
| 15316:Multiple plates on drum (or head out of alignment by %d microns). Cancelimage to unload plate. |
15317:Autoloader is suspended and cannot accept new commands. |
| 15318:Manual bypass loading is not supported on this machine. |
15319:Plates are sticking together. Please open the plate cover and separate the plates.Press RESUME to continue. |
| 15320:STEP : axis 2 communication error |
15321:STEP : axis 2 is busy |
| 15322:STEP : axis 2 initialization error |
15323:STEP : axis 2 not initialized |
| 15324:STEP : axis 2 SW error: invalid PARAMETER |
15325:STEP : axis 2 aborted while moving |
| 15326:STEP : axis 2 SW error: invalid STATE |
15327:STEP : axis 2 distance out of range |
| 15328:STEP : axis 2 timed out while aborting |
15329:STEP : axis 2 distance must be positive |
| 15330:STEP : axis 2 already moving |
15331:STEP : axis 2 HOME limit switch is active |
| 15332:STEP : axis 2 AWAY limit switch is active |
15333:STEP : axis 2 timed out while homing |
| 15334:STEP : axis 2 timed out while moving |
15335:Please close access door |
| 15336:Timeout waiting for QSPI system to initialize, stepper drive task startup failed |
15340:Punch communication error: error sending dataPunch communication error: Timeout waiting for punch responsePunch communication error: Timeout waiting for punch status informationPunch communication error: unknown information messagePunch communication error: Timeout waiting for punch error messagePunch communication error: unknown error informationPunch communication error: unexpected status signal |
| 15341:Error: request to rotate plate when rotator not properly installed |
15342:Error: request to punch plate when punch not properly installed |
| 15343:Punch reported status error: punch chip drawer requires emptyingPunch reported status error: punch heads require oilingPunch reported status error: low air pressurePunch reported status error: punch not in automatic mode, check keypad if present |
15344:Punch reported mechanical error: plate still in punchPunch reported mechanical error: problem moving punch inlayPunch reported mechanical error: problem moving punch stopPunch reported mechanical error: problem raising or lowering punch inlayPunch reported mechanical error: problem with punch plate sensorPunch reported mechanical error: punch could not find plate edge |
| 15345:Punching error: plate did not register on punchPunching error: plate not free of punchPunching error: Timeout waiting for plate to passPunching error: Timeout waiting for punch to be readyPunching error: Timeout waiting for side registrationPunching error: Timeout waiting for punching to completePunching error: Timeout waiting for inlay to move downPunching error: Timeout waiting for plate to registerPunching error: Plate still touching stops |
15346:Punch status is okay |
| 15347:The punch is still waiting for the last plate to leave. |
15348:Picker wrist sensor isn't working |
| 15349:Picker wrist cylinder is faulty |
15350:STEP : axis 1 communication error |
| 15351:STEP : axis 1 is busy |
15352:STEP : axis 1 initialization error |
| 15353:STEP : axis 1 not initialized |
15354:STEP : axis 1 SW error: invalid PARAMETER |
| 15355:STEP : axis 1 aborted while moving |
15356:STEP : axis 1 SW error: invalid STATE |
| 15357:STEP : axis 1 distance out of range |
15358:STEP : axis 1 timed out while aborting |
| 15359:STEP : axis 1 distance must be positive |
15360:STEP : axis 1 HOME limit switch is active |
| 15362:STEP : axis 1 AWAY limit switch is active |
15363:STEP : axis 1 timed out while homing |
| 15364:STEP : axis 1 timed out while moving |
15365:please close access door |
| 15366:invalid axis number |
15367:unload sensor not detected during stepper jog |
| 15368:Timeout waiting for QSPI system to initialize, stepper drive task startup failed |
15369:Proof type #<n> is invalid or not set up correctly |
| 15370:Timeout moving the cr from drum to homeTimeout moving the cr from vr to homeTimeout moving the cr, it is lost!!!Timeout moving the cr from home to vrTimeout moving the cr from home to drumTimeout moving the VR to NeutralTimeout moving the VR to DrumTimeout moving the VR to TrayTimeout moving the tape roller upTimeout moving the tape roller down |
15371:Media detected on unload ramp, please removeMedia detected on drum, please remove |
| 15372:No media detected on unload ramp, check inside machine |
15373:Drum vacuum level too low, threshold = <n>, current level = <n> (index word) |
| 15374:Drum vacuum level too high, threshold = <n>, current level = <n> (index word) |
15375:timeout waiting for Roller 4-Up suction to build up, threshold = <n>, current level = <n> (index word)timeout waiting for Roller 4-Up suction to release, threshold = <n>, current level = <n> (index word)timeout waiting for Roller 8-Up suction to build up, threshold = <n>, current level = <n> (index word)timeout waiting for Roller 8-Up suction to release, threshold = <n>, current level = <n> (index word) |
| 15376:Carrier required to do this proofing command |
15377:donor on drum |
| 15378:Due to previous job error, please verify that the next media in the cassette is a |
15379:cassette not installed correctly |
| 15380:expected 4-page cassetteexpected 8-page cassette |
15381:vacuum roller on drumcleaning roller on drum |
| 15382:receiver on drum |
15383:Media partially on drum. Remove carrier from drum.Media partially on drum. Remove receiver from drum.Media partially on drum. Remove donor and receiver from drum.Media partially on drum. Remove media other than carrier from drum. |
| 15384:Wrong sized or invalid carrier loaded |
15385:No media detected or media jammed in cassette, check cassette tray or reseat media. |
| 15386:Mis-loaded carrier detected (dvac).Click RESUME and wait 1 min before reload. |
15387:Media loaded incorrectly due to fly-off, remove donor and receiver from drumMedia loaded incorrectly due to fly-off, remove receiver from drum |
| 15388:Carrier loaded incorrectly due to fly-off, remove carrier from drum |
15389:carrier not detected on load ramp |
| 15390:carrier larger than expected. Please remove carrier. |
15391:carrier smaller than expected. Please remove carrier. |
| 15392:No carrier on drum. Possible software error. |
15393:Invalid or mis-loaded carrier (optical).Expecting <proof-type name> carrier.Click RESUME and wait 1 min before reload. |
| 15394:carrier on drum |
15395:Media loaded incorrectly due to drum vacuum detected fly-off. Removedonor and receiver from drum. |
| 15396:Dvac generator unable to maintain the vacuum level. Switch to Dvac pump. |
15397:Vacuum ADC calibration required (sensor type) |
| 15398:Important!Visually inspect the drum.If drum is EMPTY, click MEDIA CLEAR.Otherwise, click RESUME. |
15399:Replace Drum Vacuum with next service.Resume to continue |
| 15400:Drum Vacuum turned off unexpectingly.Resume to continue |
15501:invalid state |
| 15502:software error!! |
15503:ALE board still in reset |
| 15504:ALE board not responding |
15505:%s %d invalid MODE |
| 15506:command already in progress |
15507:Autoloader operation aborted |
| 15508:Autoloader not initialized |
15509:System air pressure too low! |
| 15510:Processor channel %d is invalid |
15511:not implemented yet |
| 15512:satellite board address out of range |
15520:%s %d communication error |
| 15521:%s %d is busy |
15522:%s %d initialization error |
| 15523:%s %d not initialized |
15524:%s %d SW error: invalid PARAMETER |
| 15525:%s %d aborted while moving |
15526:%s %d SW error: invalid STATE |
| 15527:%s %d distance out of range |
15528:%s %d timed out while aborting |
| 15529:%s %d distance must be positive |
15530:%s %d already moving |
| 15531:%s %d HOME limit switch is active |
15532:%s %d AWAY limit switch is active |
| 15533:%s %d timed out while homing |
15534:%s %d timed out while moving |
| 15535:please close access door |
15539:engine mount lock cylinders didn't move |
| 15540:move clamps to park position, then select RESUME |
15542:trailing edge clamps failed to unlock |
| 15543:trailing edge clamps failed to lock |
15544:trailing edge clamps not on actuator |
| 15545:trailing edge clamps on actuator |
15546:trailing-edge actuator on drum |
| 15547:timeout moving trailing edge cylinder |
15548:timeout moving air cylinder |
| 15549:leading-edge actuator on drum |
15550:timeout moving leading edge cylinder |
| 15551:timeout moving roller cylinder |
15552:roller on drum |
| 15553:balance weight actuators extended |
15554:timeout moving balance weight actuator |
| 15555:unable to detect balance weight %d |
15556:timeout moving load/unload table |
| 15557:load/unload table is in the UP position |
15558:load/unload table is in the DOWN position |
| 15559:timeout moving unload table |
15560:unload table cow-catcher is extended, can't move drum |
| 15561:timeout moving unload table cow-catcher |
15562:timeout moving exit flap |
| 15563:cannot move the bay %d tissue compactor, the box lid is in the way |
15564:please pull the plate carrier out of bay %d |
| 15565:busy with bay %d, cannot process new message code %04Xh |
15566:bay %d safety interlock is open |
| 15567:timeout loading bay %d |
15568:bay %d is disabled and turned offline |
| 15569:please close the door on bay %d |
15570:please push the carrier in bay %d all the way in |
| 15571:bay %d in use |
15572:bay %d is open |
| 15573:bay %d location not initialized in NVS |
15574:new bay number out of range |
| 15575:picker inside bay %d, not safe to move |
15576:plate box carrier in bay %d is not in the home position |
| 15577:bay %d box lid not open |
15578:timeout moving bay %d cassette lid |
| 15579:missing bay %d cassette lid |
15580:bay %d cassette lid already on grippers |
| 15581:timeout moving bay %d cassette lid grippers |
15582:timeout moving bay %d shutter cylinder |
| 15583:bay %d failed to lock |
15584:bay %d tab not found |
| 15585:stuck on bay %d tab |
15590:picker plate-detect microswitch stuck on |
| 15593:timeout homing bay %d paper sweeper |
15594:timeout while crushing slip-sheets in bay %d |
| 15595:bay %d paper sweeper is skewed, please move home |
15596:bay %d paper sweeper not responding |
| 15597:bay %d paper sweeper blocking action, not home or away |
15598:sensors indicate bay %d paper sweeper both home and away |
| 15599:Please move the bay %d paper sweeper home or away |
15600:plate in bay %d is not metal |
| 15601:plate in bay %d is metal |
15602:plate not found, check picker suction cup adjustment |
| 15603:plate loaded incorrectly, remove plate from drum |
15604:plate too small, remove from load ramp |
| 15605:plate too large or slip sheet attached, remove from load ramp |
15606:plate lost after picking, check inside recorder |
| 15607:plate on picker, please remove |
15608:no plate on picker or low vac, can't continue |
| 15609:plate on turtle, please remove |
15610:no plate on turtle or low vac, can't continue |
| 15611:plate on load ramp, please remove |
15612:no plate on load ramp or low vac, can't continue |
| 15613:plate on unload ramp, please remove |
15614:no plate on unload ramp or low vac, can't continue |
| 15615:plate stuck on unload ramp |
15616:plate on bridge, please remove |
| 15617:no plate on bridge, can't continue |
15618:plate on drum, please remove |
| 15619:no plate on drum, can't continue |
15621:no plate on unload X-axis or low vac, can't continue |
| 15622:PICK command already in progress |
15623:FETCH command already in progress |
| 15624:LOAD command already in progress |
15625:UNLOAD command already in progress |
| 15626:EJECT command already in progress |
15627:EJECT command timed out |
| 15628:no plate on push-bar or plate size wrong, can't continue |
15630:trailing edge clamp status unknown,\\ possible software or sensor error #%d. |
| 15631:Picker board not responding or wrong version |
15632:Turtle board not responding or wrong version |
| 15633:Engine board not responding or wrong version |
15634:Unload Ramp board not responding or wrong version |
| 15636:Cassette Bay 1 & 2 board not responding or wrong version |
15637:Cassette Bay 3 & 4 board not responding or wrong version |
| 15638:Cassette Bay 5 & 6 board not responding or wrong version |
15640:picker Z-axis not in handoff position |
| 15641:turtle W-axis not in position for plate hand-off |
15642:picker Z-axis not HOME |
| 15643:picker Z-axis not in position for plate grab |
15644:engine_is_installed flag is set to 0! |
| 15646:Load ramp lid is open, please close and RESUME |
15647:picker Y-axis not AWAY |
| 15648:turtle Y-axis not AWAY |
15660:Waiting for the bay %d door to close |
| 15661:Waiting for the bay %d carrier to get home |
15662:Crushing the tissues in bay %d |
| 15663:Closing the cassette lid in bay %d |
15664:Opening the cassette lid in bay %d |
| 15665:processor number is invalid, check process[] NVS setting |
15666:ejector motor %d stalled, check for plate in bridge |
| 15667:timeout moving ejector %d rollers, check hall sensors |
15668:timeout waiting for plate to leave ejector %d |
| 15669:bridge motor %d stalled, check for plate in bridge |
15670:timeout moving bridge %d rollers |
| 15671:timeout waiting for plate to leave bridge %d |
15672:PROCESS command aborted, check for plate in bridge |
| 15673:please lower processor bridge |
15674:please close bridge lid |
| 15675:please close cassette-bay side access door |
15676:please close front access door |
| 15677:please close roof access door |
15678:picker in bay %d, select RESUME |
| 15679:counter balance weights shifted |
15680:pick could not complete because table is up |
| 15681:timeout moving tec backbone up or down |
15682:attempt to move backbone with tec locked |
| 15683:plate expected to cover lower load sensor |
15684:plate expected to be sensed in ejector |
| 15685:attempt to move table while plate in ejector %d |
15686:calculated balance weight offset too large |
| 15687:balance weights not detected. Confirm position |
15688:plate length wrong. Remove plate from load table and configure bay |
| 15690:timeout waiting for vacuum to release. |
15693:forced failure. Type 'ale step fail clear' to continue |
| 15694:Config picker command in progress, select RESUME when complete |
15695:picker Y-axis not HOME |
| 15696:turtle W-axis not HOME |
15697:turtle Y-axis not HOME |
| 15800:operation timed out |
15801:invalid state |
| 15802:software error!! |
15803:ALE board still in reset |
| 15804:ALE board not responding |
15805:%s %d invalid MODE |
| 15806:command already in progress |
15807:Autoloader operation aborted |
| 15808:Autoloader not initialized |
15809:System air pressure too low! |
| 15810:not implemented yet |
15811:satellite board address out of range |
| 15812:Autoloader operation aborted because a door is open |
15813:Plate under 762 mm, load onto leftmost and third pin from the left. |
| 15814:Plate under 559 mm, load onto leftmost two pins. |
15820:move clamps to park position, then select RESUME |
| 15821:Select RESUME to recover clamps from drum or CLEAR to cancel |
15822:trailing edge clamps failed to unlock |
| 15823:trailing edge clamps failed to lock |
15824:trailing edge clamps not detected on actuator |
| 15825:trailing edge clamps detected on actuator |
15826:trailing-edge actuator on drum |
| 15827:timeout moving trailing edge cylinder |
15828:timeout moving air cylinder |
| 15829:leading-edge actuator on drum |
15830:timeout moving leading edge cylinder |
| 15841:timeout moving roller cylinder |
15842:roller on drum |
| 15843:balance weight actuators extended |
15844:timeout moving balance weight actuator |
| 15845:unable to detect balance weight %d |
15846:counter balance weights shifted |
| 15847:balance weights are not detected near detent 0 |
15848:timeout moving tec backbone up or down |
| 15849:attempt to move backbone with tec locked |
15859:unloading plate from drum, wrong size for current image |
| 15860:plate load failed, remove from drum and select \"Plate Removed\". |
15861:plate (%lu mm) smaller than expected (%lu mm), remove from load table or correct the size |
| 15862:plate (%lu mm) larger than expected (%lu mm), remove from load table or correct the size |
15863:plate on drum, please remove |
| 15864:no plate on drum, can't continue |
15865:LOAD command already in progress |
| 15866:UNLOAD command already in progress |
15867:trailing edge clamp status unknown,\\ possible software or sensor error #%d. |
| 15868:Engine board not responding or wrong version |
15869:engine_is_installed flag is set to 0! |
| 15877:The table took too long to move up. |
15878:The table took too long to move down. |
| 15879:It took too long for the table to be lifted up. |
15880:It took too long for the table to be lowered down. |
| 15881:It's taking too long for the button to be pressed. |
15882:It's taking too long for the plate to be removed. |
| 15883:Load command has been cancelled. |
15884:The plate door is taking too long to open. |
| 15885:The plate door is taking too long to close. |
15886:The plate door is taking too long to close on the table. |
| 15887:Plate not grabbed by the table vacuum. |
15888:Plate not detected by the table's plate sensor. |
| 15889:Remove the plate from the load/unload table then select \"Resume\". |
15890:A door is open, please check that all doors are securely closed. |
| 15892:Press the start button when you are ready to continue. |
15893:Please lift the table to the upright position to continue. |
| 15894:Please lower the table all the way down to continue. |
15957:Software error: invalid lamp state %d in set_lamp_state() |
| 15958:Software error: invalid image task state %d in update_lamps() |
15959:The sensor_to_plate length (%lu mm) is larger than the plate_height (%lu mm)! |
| 15960:The roller_pos (%lu ticks) is past the trailing edge of the plate (%lu ticks)! |
15961:Balance weights not detected. Confirm position |
| 15968:Plate registration not detected, adjust plate |
15969:Plate size too small, plate mainscan verification disabled |
| 15970:Timeout waiting for the ADC pressure to settle |
15971:System air pressure fell below threshold required for PCUPS during operation |
| 15972:System air pressure fell below threshold required for Picker Vacuum during operation |
15973:System air pressure fell below threshold required for Table Vacuum during operation |
| 15974:System air pressure fell below threshold required for Slipsheet Vacuum during operation |
15975:System air pressure fell below threshold required for Separators during operation |
| 15976:System air pressure fell below threshold required for Picker Deck float during operation |
15977:System air pressure fell below threshold required for Slipsheet picker blower during operation |
| 15978:System air pressure fell below threshold required for Table Plate Holder during operation |
15979:System air pressure fell below threshold required for Table Cup Blower, during operation |
| 15980:System air pressure fell below threshold required for Table Load vacuum during operation |
15987:Pdoor was not fully open when trying to lower/raise table - check pdoor sensors |
| 15988:Table vacuum is above threshold (tvt) before unloading plate. |
15989:Vacuum sensor %d offset too large during sensor null calibrating. |
| 15990:Cannot move table because state is unknown, check sensors. |
15991:System pressure sensor offset is not calibrated. Run cal pressure |
| 15992:plate may be partly on drum, please remove |
15993:Sensor offset too large ,%s |
| 15994:Pressure Sensor Cal invalid, %d; (range: min %d, max %d) |
15995:Pressure Sensor Cal invalid |
| 15996:WARNING: Inadequate air supply |